battery NISSAN TEANA 2003 Service Manual

GW-38
POWER WINDOW SYSTEM

2. CHECK REAR POWER WINDOW SWITCH
1. Turn ignition switch OFF.
2. Disconnect rear power window switch LH connector.
3. Check continuity between rear power window switch LH terminal
1, 2, 3 and 4, 5.
OK or NG
OK >> GO TO 3.
NG >> Replace rear power window switch LH.
3. CHECK HARNESS CONTINUITY 1
1. Check continuity between rear power window switch LH connec-
tor D54 terminal 4, 5 and rear power window motor LH connec-
tor D55 terminal 1, 2.
2. Check continuity between rear power window switch LH connec-
tor D54 terminal 4, 5 and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace harness.
4. CHECK REAR POWER WINDOW SWITCH POWER SUPPLY
1. Turn ignition switch ON.
2. Check voltage between rear power window switch LH connector
D54 terminal 1 and ground.
OK or NG
OK >> GO TO 6.
NG >> GO TO 5.
Terminals Condition of switch Continuity
15 UP
Ye s 14 DOWN
2 5 No operation
3 4 No operation
PIIA4186E
4 (L/B) – 1 (L/B) : Continuity should exist.
5 (L/R) – 2 (L/R) : Continuity should exist.
4 (L/B) – Ground : Continuity should not exist.
5 (L/R) – Ground : Continuity should not exist.
PIIB0618E
1 (L/W) – Ground : Battery voltage
PIIB0615E

POWER WINDOW SYSTEM
GW-39
C
D
E
F
G
H
J
K
L
MA
B
GW

5. CHECK HARNESS CONTINUITY 2
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM connector M4 terminal 53 and
rear power window switch LH connector D54 terminal 1.
4. Check continuity between BCM connector M4 terminal 53 and
ground.
OK or NG
OK >> Check condition of harness and connector.
NG >> Repair or replace harness.
6. CHECK HARNESS CONTINUITY 3
1. Disconnect power window main switch connector.
2. Check continuity between power window main switch connector
D6 terminal 1, 3 and rear power window switch LH terminal 2, 3.
3. Check continuity between power window main switch connector
D6 terminal 1, 3 and ground.
OK or NG
OK >> GO TO 7.
NG >> Repair or replace harness.
7. CHECK POWER WINDOW MAIN SWITCH OUTPUT SIGNAL
1. Connect power window main switch connector.
2. Turn ignition switch ON.
3. Check voltage between power window main switch connector
and ground when operating rear LH switch in power window
main switch.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace power window main switch.53 (L/W) – 1 (L/W) : Continuity should exist.
53 (L/W) – Ground : Continuity should not exist.
PIIA6284E
1 (G/Y) – 2 (G/Y) : Continuity should exist.
3 (G/O) – 3 (G/O) : Continuity should exist.
1 (G/Y) – Ground : Continuity should not exist.
3 (G/O) – Ground : Continuity should not exist.
PIIB0616E
ConnectorTerminals (Wire color)
Condition of
switchVoltage [V]
(Approx.)
(+) (-)
D61 (GY)
GroundUP Battery voltage
DOWN 0
3 (G/O)UP 0
DOWN Battery voltage
PIIA4187E

GW-44
POWER WINDOW SYSTEM

7. CHECK HARNESS CONTINUITY 3
1. Disconnect power window main switch connector.
2. Check continuity between power window main switch connector
D6 terminal 2 and front power window motor (driver side) con-
nector D8 terminal 3.
OK or NG
OK >> Replace power window main switch.
NG >> Repair or replace harness.
Check Door Switch BIS000ZN
1. CHECK DOOR SWITCH INPUT SIGNAL
With CONSULT-II
Check “DOOR SW-DR ” in “DATA MONITOR” mode with CONSULT-II.
Without CONSULT-II
Check voltage between BCM connector M5 terminal 62 and ground.
OK or NG
OK >> Door switch circuit is OK.
NG >> GO TO 2.2 (W/B) – 3 (W/B) : Continuity should exist.
PIIB0627E
Monitor item Condition of driver side door
DOOR SW-DROPEN : ON
CLOSE : OFF
PIIB0629E
ConnectorTerminals (Wire color) Condition of
driver side
doorVoltage [V]
(Approx.)
(+) (–)
M5 62 (SB) GroundOPEN 0
CLOSE Battery voltage
PIIB0630E

POWER WINDOW SYSTEM
GW-45
C
D
E
F
G
H
J
K
L
MA
B
GW

2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect front door switch (driver side) and BCM connector.
3. Check continuity between BCM connector M5 terminal 62 and
front door switch (driver side) connector B10 terminal 2.
4. Check continuity between BCM connector M5 terminal 62 and
ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR SWITCH
Check continuity between front door switch (driver side) terminal 2
and ground part of door switch.
OK or NG
OK >> GO TO 4.
NG >> Replace door switch.
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Check voltage between BCM connector M5 terminal 62 and
ground.
OK or NG
OK >> Check condition of harness and connector.
NG >> Replace BCM.
Check Power Window Lock Switch BIS000ZO
1. CHECK POWER WINDOW LOCK SIGNAL
Exchanges for a normal power window main switch, and check operation.
Does power window lock operate?
YES >> Replace power window main switch.
NG >> Check condition of harness and connector.62 (SB) – 2 (SB) : Continuity should exist.
62 (SB) – Ground : Continuity should not exist.
PIIB1327E
TerminalCondition of door
switchContinuity
2Ground part of
door switchPushed No
Released Yes
PIIB1328E
62 (W) – Ground : Battery voltage
PIIB0630E

GW-62
REAR WINDOW DEFOGGER

Terminal and Reference Value for BCMBIS00102
Terminal and Reference Value for IPDM E/RBIS00103
Work FlowBIS00104
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to GW-54, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction.
Refer to GW-63, "
Trouble Diagnoses Symptom Chart" .
4. Does rear window defogger operate normally?
YES: GO TO 5.
NO: GO TO 3.
5. INSPECTION END
Te r m i -
nalWire
colorItemSignal
Input/
OutputConditionVoltage [V]
(Approx.)
9GR/LRear window defogger
switch signalInputWhen rear window defogger switch is pressed. 0
When rear window defogger switch is OFF. 5
38 R Ignition switch ON or START Input Ignition switch (ON or START position) Battery voltage
39 L CAN− HInput/
Output——
40 P CAN− LInput/
Output——
42 Y/R Power source (Fuse) Input — Battery voltage
52 B Ground — — 0
55 W/B Power source (Fusible link) Input — Battery voltage
Te r m i -
nalWire
colorItemSignal
Input/
OutputConditionVoltage [V]
(Approx.)
6 L Battery power supply Output — Battery voltage
38 B Ground (Power) Output — 0
48 L CAN− HInput/
Output——
49 P CAN− LInput/
Output——
52 G/RRear window defogger relay
control signalInputWhen rear window defogger switch is ON. 0
When rear window defogger switch is OFF. Battery voltage
60 B Ground (Signal) — — 0

GW-64
REAR WINDOW DEFOGGER

Check BCM Power Supply and Ground Circuit BIS00107
First perform the “SELF-DIAG RESULTS” in “BCM” with CONSULT-II, when perform the each trouble
diagnosis. Refer to BCS-14, "
CAN Communication Inspection Using CONSULT-II (Self-Diagnosis)" .
1. CHECK FUSE

10A fuse [No.1, located in fuse block (J/B)]

15A fuse [No.17, located in fuse block (J/B)]

50A fusible link (letter M, located in the fuse and fusible link box).
NOTE:
Refer to GW-54, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse. Refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
Check voltage between BCM connector and ground.
OK or NG
OK >> GO TO 3.
NG >> Check BCM power supply circuit for open or short.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM connector.
3. Check continuity between BCM connector M4 terminal 52 and
ground.
OK or NG
OK >> Power supply and ground circuit are OK.
NG >> Check BCM ground circuit for open.
ConnectorTerminal
Condition of ignition
switchVoltage [V]
(Approx.)
(+) (-)
M338 (R)
GroundON
Battery voltage 42 (LG)
OFF
M4 55 (W/B)
PIIB1097E
52 (B) – Ground : Continuity should exist.
PIIB1099E

GW-66
REAR WINDOW DEFOGGER

3. CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M3 terminal 9 and
ground.
OK or NG
OK >> Replace A/C and AV switch.
NG >> Replace BCM.
Check Rear Window Defogger Power Supply Circuit BIS00109
1. CHECK FUSE

10A fuse [No.12, located in fuse block (J/B)]

20A fuse (No.75, located in the IPDM E/R)
NOTE:
Refer to GW-54, "
Component Parts and Harness Connector Location" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown out, be sure to eliminate cause of malfunction before installing new fuse, refer to
PG-3, "
POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Remove rear window defogger relay.
2. Turn ignition switch ON.
3. Check voltage between rear window defogger relay connector
and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness between fuse block (J/B) and
rear window defogger relay.
3. CHECK REAR WINDOW DEFOGGER RELAY
Check continuity between rear window defogger terminals 3 and 5.
OK or NG
OK >> GO TO 4.
NG >> Replace rear window defogger relay.9 (GR/L) – Ground : Approx. 5V
PIIA6208E
1 (G) – Ground : Battery voltage
3 (L) – Ground : Battery voltage
PIIB1098E
Terminal Condition Continuity
3512V direct current supply
between terminals 1 and 2Ye s
No current supply No
SEC202B

REAR WINDOW DEFOGGER
GW-67
C
D
E
F
G
H
J
K
L
MA
B
GW

4. CHECK REAR WINDOW DEFOGGER RELAY GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Install rear window defogger relay.
3. Turn ignition switch ON.
4. Check voltage between rear defogger relay connector and
ground.
OK or NG
OK >> Rear window defogger power supply circuit is OK.
NG >> GO TO 5.
5. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and rear window defogger relay.
3. Check continuity between IPDM E/R connector E9 terminal 52
and rear window defogger relay connector B203 terminal 2.
OK or NG
OK >> Check harness connection.

If it is OK, replace IPDM E/R.

If it is NG, repair or replace malfunction part.
NG >> Repair or replace harness.
Check Rear Window Defogger Circuit BIS0010A
1. CHECK POWER SUPPLY CIRCUIT 1
1. Turn ignition switch OFF.
2. Disconnect rear window defogger connector.
3. Turn ignition switch ON.
4. Check voltage between rear window defogger connector and
ground.
OK or NG
OK >> GO TO 2.
NG >> GO TO 3.
ConnectorTerminals (Wire color)
ConditionVoltage [V]
(Approx.)
(+) (-)
B203 2 (G/R) GroundRear window defogger
switch ON0
Rear window defogger
switch OFFBattery
voltage
PIIB1282E
52 (G/R) – 2 (G/R) : Continuity should exist.
PIIA6211E
ConnectorTerminal (Wire color)
ConditionVoltage [V]
(Approx.)
(+) (–)
B251 1(G) GroundRear window defogger
switch ON Battery voltage
Rear window defogger
switch OFF0
PIIA4234E

REAR WINDOW DEFOGGER
GW-69
C
D
E
F
G
H
J
K
L
MA
B
GW

2. CHECH REAR WINDOW DOFOGGER RELAY POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Remove rear window defogger relay.
3. Turn ignition switch ON.
4. Check voltage between rear window defogger relay harness
connector B203 terminal 6 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK REAR WINDOW DEFOGGER RELAY
Check continuity between rear window defogger relay terminal 6 and 7.
OK or NG
OK >> GO TO 4.
NG >> Replace rear window defogger relay.
4. CHECK HARENSS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect door mirror connector.
3. Check continuity between door mirror D3 (driver side), D33
(passenger side) terminal 2 and rear window defogger relay
connector B203 terminal 7.
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> Repair or replace harness.6 (W) - Ground : Battery voltage
PIIA9561E
Terminal Condition Continuity
6712V direct current supply
between terminals 1 and 2Ye s
No current supply No
SEC202B
2 (L/B) - 7 (L/B) : Continuity should exist.
PIIB2181E

GW-70
REAR WINDOW DEFOGGER

Check Driver Side Door Mirror Defogger Circuit BIS0010C
1. CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door mirror (driver side) connector.
3. Turn ignition switch ON.
4. Check voltage between door mirror (driver side) connector and
ground.
OK or NG
OK >> GO TO 2.
NG >> Repair or replace harness.
2. CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between door mirror (driver side) connector D3
terminal 3 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair or replace harness.
3. CHECK DOOR MIRROR DEFOGGER
Check continuity between door mirror (driver side) terminal 2 and 3.
OK or NG
OK >> Check the condition of the harness and the connector.
NG >> Replace door mirror (driver side).
ConnectorTerminal (Wire color)
Condition of rear win-
dow defogger switchVoltage (V)
(Approx.)
(+) (–)
D3 2 (L/B) GroundON Battery voltage
OFF 0
PIIB2182E
3 (B) – Ground : Continuity should exist.
PIIB2183E
2 – 3 : Continuity should exist.
PIIB2184E