wheel NISSAN TEANA 2003 Workshop Manual

TROUBLE DIAGNOSIS
BRC-55
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

Control Unit Input/Output Signal SpecificationsBFS000E1
REFERENCE VALUE FROM CONSULT-II
CAUTION:
The monitor displays the control unit calculation data. The normal values will be displayed even in the
event that the output circuit (harness) is open or shorted.
Monitor item Display itemDATA MONITOR
ConditionReference values for
normal operation
WHEEL SENSORVehicle speed calculated using sig-
nals from all four wheel sensorsVehicle stopped 0 [km/h (MPH)]
Vehicle running (Note 1)Almost in accordance
with speedometer dis-
play (within ± 10 %)
DECEL G SENSOR Decel G detected by decel G sensorWhen stopped -0.11 to +0.11 G
During acceleration Negative value
During deceleration Positive value
IN ABS S/V
OUT ABS S/VOperation condition of all solenoid
valvesWhen the actuator solenoid operates ON
When the actuator relay operates and
the actuator solenoid does not operateOFF
EBD WARN LAMP
(Note 2)Brake warning lamp ON/OFF condi-
tionWhen brake warning lamp is ON ON
When brake warning lamp is OFF OFF
STOP LAMP SW Brake pedal operation conditionBrake pedal depressed ON
Brake pedal not depressed OFF
MOTOR RELAYMotor and motor relay operation con-
ditionWhen motor relay and motor are
operatingON
When motor relay and motor are not
operatingOFF
ACTUATOR RLY Actuator relay operation conditionActuator relay activated ON
Actuator relay not activated OFF
ABS WARN LAMPABS warning lamp ON/OFF condition
(Note 3)When ABS warning lamp is ON ON
When ABS warning lamp is OFF OFF
OFF LAMPVDC OFF indicator lamp ON/OFF
condition (Note 4)When VDC OFF indicator lamp is ON ON
When VDC OFF indicator lamp is OFF OFF
OFF SW VDC OFF switch ON/OFF conditionWhen VDC OFF switch ON
(When the VDC OFF indicator lamp is
ON)ON
When VDC OFF switch OFF
(When the VDC OFF indicator lamp is
OFF)OFF
SLIP LAMPSLIP indicator lamp ON/OFF condi-
tion (Note 5)When SLIP indicator lamp is ON ON
When SLIP indicator lamp is OFF OFF
BATTERY VOLTBattery voltage supplied to ABS actu-
ator and electric unit (control unit)Ignition switch ON 10 - 16 V
GEARDetermined gearshift position from
the A/T switch signalAlways1: 1st gear
2: 2nd gear
3: 3rd gear
4: 4th gear
ENGINE SPEED Engine runningWith engine stopped 0 rpm
Engine runningAlmost in accordance
with tachometer display
YAW RATE SEN Yaw rate detected by yaw rate sensor When stopped−7.0 to +7.0 d/s

BRC-56
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS

Note 1: Confirm tire pressure is the standard value.
Note 2: Warning lamp can be used as both EBD warning lamp and brake warning.N POSI SIGShift position determined by the A/T
switch signalWhen in N position ON
Other than N position OFF
P POSI SIGShift position determined by the A/T
switch signalWhen in P position ON
Other than P position OFF
FR LH IN SOL
FR LH OUT SOL
FR RH IN SOL
FR RH OUT SOL
RR LH IN SOL
RR LH OUT SOL
RR RH IN SOL
RR RH OUT SOLOperation condition of all solenoid
valvesActuator (solenoid) is active (“ACTIVE
TEST” with CONSULT-II) and actuator
relay is active (ignition switch ON)ON
When actuator (solenoid) is not active
or actuator relay is not active (in fail-
safe mode)OFF
STOP LAMP SW2 Brake pedal operation conditionBrake pedal depressed ON
Brake pedal not depressed OFF
ACCEL POS SIGAccelerator open/close condition
(linked to the accelerator pedal)Do not step on the accelerator pedal
(When ignition switch is on)0 %
Step on the accelerator pedal
(When ignition switch is on)0 - 100 %
SIDE G SENSOR Side G detected by side G sensorWhen stopped
−1.1 to +1.1 m/s
2
Right turn Negative value
Left turn Positive value
STR ANGLE SIGSteering angle detected by steering
angle sensorStraight-ahead position -3.5° to 3.5°
Steering wheel turned right 0° to 756°
Steering wheel turned left 0° to -756°
EBD SIGNAL EBD operation conditionEBD activated ON
EBD not activated OFF
ABS SIGNAL ABS operation conditionABS activated ON
ABS not activated OFF
TCS SIGNAL TCS operation conditionTCS activated ON
TCS not activated OFF
VDC SIGNAL VDC operation conditionVDC activated ON
VDC not activated OFF
EBD FAIL SIG EBD fail-safe signal conditionIn EBD fail-safe ON
EBD is normal OFF
ABS FAIL SIG ABS fail-safe signal conditionIn ABS fail-safe ON
ABS is normal OFF
TCS FAIL SIG TCS fail-safe signal conditionIn TCS fail-safe ON
TCS is normal OFF
VDC FAIL SIG VDC fail-safe signal conditionIn VDC fail-safe ON
VDC is normal OFF
CRANKING SIG Cranking conditionAt cranking ON
Other than at cranking OFF
FLUID LEV SWBrake fluid level switch ON/OFF con-
ditionWhen brake fluid level switch is ON ON
When brake fluid level switch is OFF OFF Monitor item Display itemDATA MONITOR
ConditionReference values for
normal operation

BRC-58
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS

Self-DiagnosisBFS000E3
DESCRIPTION

If an error is detected in the system, ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp
on the combination meter turn on. In this case, perform self-diagnosis as follows:

While CONSULT-II is used, ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp may be
turned on in a case of no malfunctioning.
OPERATION PROCEDURE
1. Turn ignition switch OFF.
2. Perform CONSULT-II Starting Procedure. Refer to GI-34, "
CONSULT-II Start Procedure" .
3. Turn ignition switch ON.
4. Start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately 1 minute.
5. After stopping vehicle, with the engine running, touch “ABS”, “SELF-DIAG RESULTS” in order on the
CONSULT-II screen.
CAUTION:
If “START (NISSAN BASED VHCL)” is touched immediately after starting engine or turning on the
ignition switch, “ABS” might not be displayed in the System Selection screen. In this case, repeat
the operation from step 1. If it cannot be shown after several attempts, ABS actuator and electric
unit (control unit) may have malfunctioned.
6. The self-diagnostic results are displayed. (Touch “PRINT” to print out self-diagnostic results, if necessary.)

Check ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp if “NO FAILURE” is dis-
played.
7. Perform the appropriate inspection from the display item list, and repair or replace the malfunctioning
component.
8. Start engine and drive vehicle at 30 km/h (19 MPH) or more for approximately 1 minute.
CAUTION:
When the wheel sensor malfunctions, after inspecting the wheel sensor system, the ABS warning
lamp, VDC OFF indicator lamp and SLIP indicator lamp will not turn off even when the system is
normal unless the vehicle is driving at 30 km/h (19MPH) or more for approximately 1 minute.
ERASE MEMORY
1. Turn ignition switch OFF.
2. Start engine and touch “ABS”, “SELF-DIAG RESULTS”, “ERASE MEMORY” in order on the CONSULT-II
screen to erase the DTC memory.
CAUTION:
If the error memory is not erased, re-perform the operation from step 4.
3. Perform self-diagnosis again, and make sure that diagnostic memory is erased.
4. Drive vehicle at 30 km/h (19 MPH) or more for approximately 1 minute as the final inspection, and make
sure that the ABS warning lamp, VDC OFF indicator lamp and SLIP indicator lamp turn off.
CAUTION:
VDC OFF switch should not stay in the “ON” position.

TROUBLE DIAGNOSIS
BRC-59
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

DISPLAY ITEM LIST
Diagnostic item Diagnostic item is detected when... Reference
RR RH SENSOR−1
[C1101]When the circuit in the rear right wheel sensor is open.
BRC-68, "
Wheel Sensor
System"
(Note 1) RR LH SENSOR−1
[C1102]When the circuit in the rear left wheel sensor is open.
FR RH SENSOR−1
[C1103]When the circuit in the front right wheel sensor is open.
FR LH SENSOR−1
[C1104]When the circuit in the front left wheel sensor is open.
RR RH SENSOR−2
[C1105]When the circuit in the rear right wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
RR LH SENSOR−2
[C1106]When the circuit in the rear left wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
FR RH SENSOR−2
[C1107]When the circuit in the front right wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
FR LH SENSOR−2
[C1108]When the circuit in the front left wheel sensor is shorted. Or when
the sensor power voltage is outside the standard. When the dis-
tance between the wheel sensor and sensor rotor is too large and
the sensor pulse cannot be recognized by the control unit.
BATTERY VOLTAGE
[ABNORMAL]
[C1109]Battery voltage of control unit is too low.BRC-78, "
ABS Actuator
and Electric Unit (Control
Unit) Power Supply and
Ground System"
CONTROLLER FAILURE
[C1110]When there is an internal malfunction in the control unit.BRC-70, "ABS Actuator
and Electric Unit (Control
Unit) 1"
PUMP MOTOR
[ C 1111 ]This is displayed when the control unit detects a malfunction in the
motor or motor relay.BRC-74, "Pump Motor,
Motor Relay System"
G-SENSOR
[C1113]Longitudinal G-sensor is malfunctioning, or signal line of longitudi-
nal G-sensor is open or shorted.BRC-72, "Yaw Rate/Side/
Decel G Sensor System"
STOP LAMP SW
[C1116]Stop lamp switch circuit is open.BRC-77, "Stop Lamp
Switch System"

BRC-60
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS

Note 1: After completing repairs of the shorted sensor circuit, when ignition switch is turned ON, ABS warning lamp turns on. Make sure
that ABS warning lamp turns off while driving the vehicle at 30 km/h (19 MPH) or more for approximately 1 minute according to self-diag- FR LH IN ABS SOL
[C1120]This is displayed when the control unit detects a malfunction in the
front left wheel inlet solenoid circuit.
BRC-76, "
Solenoid and
VDC Change-Over Valve,
Actuator Relay System"
FR LH OUT ABS SOL
[C1121]This is displayed when the control unit detects a malfunction in the
front left wheel outlet solenoid circuit.
FR RH IN ABS SOL
[C1122]This is displayed when the control unit detects a malfunction in the
front right wheel inlet solenoid circuit.
FR RH OUT ABS SOL
[C1123]This is displayed when the control unit detects a malfunction in the
front right wheel outlet solenoid circuit.
RR LH IN ABS SOL
[C1124]This is displayed when the control unit detects a malfunction in the
rear left wheel inlet solenoid circuit.
RR LH OUT ABS SOL
[C1125]This is displayed when the control unit detects a malfunction in the
rear left wheel outlet solenoid circuit.
RR RH IN ABS SOL
[C1126]This is displayed when the control unit detects a malfunction in the
rear right wheel inlet solenoid circuit.
RR RH OUT ABS SOL
[C1127]This is displayed when the control unit detects a malfunction in the
rear right wheel outlet solenoid circuit.
CV 1
[C1164]When cut valve 1 circuit is open or shorted.
CV 2
[C1165]When cut valve 2 circuit is open or shorted.
SV 1
[C1166]When suction valve 1 circuit is open or shorted.
SV 2
[C1167]When suction valve 2 circuit is open or shorted.
ACTUATOR RLY
[C1140]This is displayed when the control unit detects a malfunction in
actuator relay circuit.
ENGINE SIGNAL 1- 6
[C1130, C1131, C1132, C1133,
C1134, C1136]When there is a malfunction in an engine system main
component.BRC-70, "
Engine Sys-
tem"
ST ANGLE SIG CIRCUIT
[C1143]When the steering angle sensor neutral position has deviated. Or
when a steering angle sensor malfunction is detected.BRC-71, "Steering Angle
Sensor System"
ST ANG SEN SIGNAL
[C1144]Neutral position correction of steering angle sensor is not finished.BRC-40, "Adjustment of
Steering Angle Sensor
Neutral Position"
YAW RATE SENSOR
[C1145]When yaw rate sensor malfunction is detected. Or when a yaw rate
sensor circuit open or short circuit is detected.
BRC-72, "
Yaw Rate/Side/
Decel G Sensor System"SIDE G-SEN CIRCUIT
[C1146]When a side G sensor malfunction is detected. Or the circuit of side
G sensor is open or shorted.
PNP POSI SIG
[C1154]TCS or ABS actuator and electric unit (control unit) internal mal-
function.BRC-75, "
Park/Neutral
Position (PNP) Switch
Circuit"
BR FLUID LEVEL LOW
[C1155]Brake fluid level drops. Or, when there is a short to ground in the
circuit between the ABS actuator and electric unit (control unit) and
the brake fluid level switch.BRC-80, "Brake Fluid
Level Switch System"
ST ANG SEN COM CIR
[C1156]CAN communication system or steering angle sensor has gener-
ated a malfunction.BRC-81, "CAN Communi-
cation System"
STOP LAMP SW2
[C1176]ASCD brake switch or circuit malfunction.EC-602, "DTC P1572
ASCD BRAKE SWITCH"
CAN COMM CIRCUIT
[U1000]When there is a malfunction in the CAN communication system.BRC-81, "CAN Communi-
cation System"
(Note 2) Diagnostic item Diagnostic item is detected when... Reference

TROUBLE DIAGNOSIS
BRC-61
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

nosis procedure. In addition, if wheel sensor 2 is displayed for the wheels, check the wheel sensor circuit and also check the control unit
power voltage.
Note 2: When malfunctions are detected in several systems, including the CAN communication system [U1000], perform trouble diagno-
sis on the CAN communication system.
Data MonitorBFS000E4
OPERATION PROCEDURE
1. Turn ignition switch OFF.
2. Perform “CONSULT-II Starting Procedure”. Refer to GI-34, "
CONSULT-II Start Procedure" .
3. Turn ignition switch ON.
4. At the monitor item selection screen, touch one of the items “ECU INPUT SIGNALS”, “MAIN SIGNALS” or
“SELECTION FROM MENU”.
5. Touch “START” to proceed to the data monitor screen.
DISPLAY ITEM LIST
Item (Unit)Monitor item selection
Remarks
ECU INPUT
SIGNALSMAIN SIGNALSSELECTION
FROM MENU
FR LH SENSOR
[km/h (MPH)]×××Condition of wheel speed calculated by front left
wheel sensor signal is displayed.
FR RH SENSOR
[km/h (MPH)]×××Condition of wheel speed calculated by front right
wheel sensor signal is displayed.
RR LH SENSOR
[km/h (MPH)]×××Condition of wheel speed calculated by rear left wheel
sensor signal is displayed.
RR RH SENSOR
[km/h (MPH)]×××Condition of wheel sensor calculated by rear right
wheel sensor signal is displayed.
DECEL G SEN
(G)×××Condition of decel G detected by the decel G sensor
is displayed.
FR LH IN SOL
(ON/OFF)—××Condition of front left wheel ABS inlet solenoid valve
(ON/OFF) is displayed.
FR LH OUT SOL
(ON/OFF)—××Condition of front left wheel ABS outlet solenoid valve
(ON/OFF) is displayed.
RR RH IN SOL
(ON/OFF)—××Condition of rear right wheel ABS inlet solenoid valve
(ON/OFF) is displayed.
RR RH OUT SOL
(ON/OFF)—××Condition of rear right wheel ABS outlet solenoid
valve (ON/OFF) is displayed.
FR RH IN SOL
(ON/OFF)—××Condition of front right wheel ABS inlet solenoid valve
(ON/OFF) is displayed.
FR RH OUT SOL
(ON/OFF)—××Condition of front right wheel ABS outlet solenoid
valve (ON/OFF) is displayed.
RR LH IN SOL
(ON/OFF)—××Condition of rear left wheel ABS inlet solenoid valve
(ON/OFF) is displayed.
RR LH OUT SOL
(ON/OFF)—××Condition of rear left wheel ABS outlet solenoid valve
(ON/OFF) is displayed.
EBD WARN LAMP
(ON/OFF) (Note)——×Condition of brake warning lamp (ON/OFF) is dis-
played.
STOP LAMP SW
(ON/OFF)×××Condition of stop lamp switch (ON/OFF) is displayed.
MOTOR RELAY
(ON/OFF)—××Condition of ABS motor relay (ON/OFF) is displayed.
ACTUATOR RLY
(ON/OFF)—××Condition of ABS actuator relay (ON/OFF) is dis-
played.
ABS WARN LAMP
(ON/OFF)—××Condition of ABS warning lamp (ON/OFF) is dis-
played.

BRC-64
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS

TEST ITEM
Solenoid Valve
NOTE:
The example shown is for the front right wheel. The procedure for the other wheels is the same as given
below.

When performing an active test of the ABS function, select the main item for each test item. In addition,
when performing an active test of the VDC/TCS function, select the item menu for each test item.

For the ABS solenoid valve, touch “UP” “KEEP” “DOWN”, and
for the ABS solenoid valve (ACT), touch “UP” “ACTUATOR UP”
“ACTUATOR KEEP”, and make sure that all solenoid valves (in,
out) are operating as given in the chart.
CAUTION:
Operate rear wheel valve when selecting front wheel and
operate front wheel valve when selecting rear wheel for
ABS solenoid valve (ACT).
Solenoid Valve Operation Chart
*: ON for 1 to 2 seconds after the touch, and then OFF
ABS Motor
Touch “ON ” and “OFF” on the screen, and check if ABS motor relay
and ABS actuator relay are operating as given in the following table.
SFIA2097E
OperationABS solenoid valve ABS solenoid valve (ACT)
UP KEEP DOWN UPACTUATOR
UPACTUATOR
KEEP
FR RH IN SOL OFF ON ON OFF OFF OFF
FR RH OUT SOL OFF OFF ON* OFF OFF OFF
SV 1 OFF OFF OFF OFF OFF* OFF
CV 1 OFF OFF OFF OFF OFF ON
Operation ON OFF
MOTOR RELAY ON OFF
ACTUATOR RLY ON ON
SFIA0593E

TROUBLE DIAGNOSIS
BRC-65
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

For Fast and Accurate DiagnosisBFS000E6
PRECAUTIONS FOR DIAGNOSIS

Be sure to check the procedures of “How to Perform Trouble Diagnosis” in advance. Refer to GI-4, "Gen-
eral Precautions" .

Always adjust the neutral position of steering angle sensor before driving when removing and installing
ABS actuator and electric unit (control unit), steering angle sensor, suspension parts and adjusting align-
ment. Refer to BRC-40, "
Adjustment of Steering Angle Sensor Neutral Position" .

Always erase memory after completing trouble diagnosis. Refer to BRC-58, "ERASE MEMORY" .

When inspection of the continuity or voltage between modules or units is performed, check connector ter-
minals for disconnection, looseness, bend, or collapse. Repair or replace applicable part if any non-stan-
dard condition is detected.

Intermittent malfunctions may be caused by a poor connection in the harness, connectors, and terminals.
Move harnesses, harness connectors, and terminals by hand to make sure all connections are solid and
undamaged.

Do not to forcibly extend any connector terminal if a circuit tester is used for the check.

The symptom shown in the table may occur, but the system is operating normally.
Symptom Symptom description Result
Motor operation soundThis is the operation sound of the motor in the actuator and electric unit.Slight
sound may occur during VDC, TCS and ABS operation.
Normal
Just after the engine starts, the motor operating noise may be heard. This is a
normal status of the system operation check.
System operation check soundWhen engine starts, “click” sound may be heard from engine room. This is nor-
mal status of system operation check.Normal
VDC/TCS operation
(SLIP indicator lamp ON)TCS may activate momentarily if wheel speed changes when driving over
location where friction coefficient varies, when downshifting, or when fully
depressing accelerator pedal.
Normal
Cancel the VDC/
TCS function for
the inspection on
a chassis dyna-
mometer. Before the speed meter inspection, push VDC OFF switch to cancel the VDC/
TCS function.
When accelerator pedal is depressed on a chassis dynamometer (front wheel
fixing type), the vehicle speed will not increase. This is normal. It is result of
TCS being activated by stationary front wheels. The warning lamp may also
turn on to show “sensor system malfunction” in this case. This is also normal,
and is the result of the stationary front wheels being detected. Restart engine,
and drive the vehicle at 30 km/h (19 MPH) or more to make sure that the warn-
ing lamp no longer turns on.
ABS operation
(Longer stopping distance)When driving on roads with a low coefficient of friction, such as snowy roads or
gravel roads, the stopping distance is sometimes longer for vehicles equipped
with ABS. Therefore, when driving on such roads, drive at a sufficiently
reduced speed to be safe.Normal
Sluggish feelDepending on road conditions, the driver may have a sluggish feel. This is
because traction control, which controls engine and brakes to achieve optimal
traction, has the highest priority (for safety). As a result sometimes the driver
has a less slight sluggish feel in response than usual acceleration feel.Normal

BRC-68
[VDC/TCS/ABS]
TROUBLE DIAGNOSIS FOR SYSTEM

TROUBLE DIAGNOSIS FOR SYSTEMPFP:00000
Wheel Sensor SystemBFS000E8
Check each part according to CONSULT-II self-diagnostic results, and then identify the parts to be replaced.
CAUTION:
Do not check between wheel sensor terminals.
INSPECTION PROCEDURE
1. CHECK TIRE
Check air pressure, wear and size.
Are air pressure, wear and size within the standards?
YES >> GO TO 2.
NO >> Adjust air pressure, or replace tire.
2. CHECK SENSOR AND SENSOR ROTOR

Check sensor and sensor rotor.

Check sensor rotor rubber for damage.

Check sensor for disconnection or looseness.
OK or NG
OK >> GO TO 3.
NG >> Repair sensor mount or replace sensor rotor.
3. CHECK SELF-DIAGNOSTIC RESULTS
Check self-diagnostic results.
Is above displayed on self-diagnosis display?
YES >> GO TO 4.
NO >> INSPECTION END
4. CHECK CONNECTOR
1. Disconnect ABS actuator and electric unit (control unit) connector and malfunctioning wheel sensor con-
nector. Check terminal for deformation, open circuit, pooh contact, etc., and repair or replace if any mal-
function is found.
2. Reconnect connectors, drive vehicle at 30 km/h (19 MPH) or more for approximately 1 minute, and then
perform self-diagnosis.
OK or NG
OK >> Connector terminal contact is loose, damaged, open or shorted.
NG >> GO TO 5.
Self-diagnostic results
FR RH SENSOR-1, -2
FR LH SENSOR -1, -2
RR RH SENSOR-1, -2
RR LH SENSOR-1, -2

TROUBLE DIAGNOSIS FOR SYSTEM
BRC-69
[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC

5. CHECK WHEEL SENSOR HARNESS
1. Turn ignition switch OFF and disconnect malfunctioning wheel
sensor connector E10 (FR-RH), E38 (FR-LH), C2 (RR-RH), C3
(RR-LH) and ABS actuator and electric unit (control unit) con-
nector E241.
2. Check continuity between terminals. (Also check continuity
when the steering wheel is turned right and left and when the
sensor harness inside the wheel house is moved.)
OK or NG
OK >> GO TO 6.
NG >> Repair or replace harness and connector that have malfunction.
6. CHECK WHEEL SENSOR POWER SUPPLY CIRCUIT
1. Disconnect malfunctioning wheel sensor connector.
2. Turn ignition switch ON and check voltage between wheel sen-
sor harness connector power supply terminal and ground.
OK or NG
OK >> Replace wheel sensor.
NG >> Replace ABS actuator and electric unit (control unit).
SFIA2098E
Power supply circuit Signal circuit Ground circuit
WheelABS actuator
and electric unit
(control unit)Wheel sensorABS actuator
and electric unit
(control unit)Wheel sensorABS actuator
and electric unit
(control unit)
(Signal)ABS actuator
and electric unit
(control unit)
(Ground)
Front RH 26 1 27 2 26, 27
31, 46 Front LH 14 1 13 2 14, 13
Rear RH 12 1 11 2 11, 12
Rear LH 28 1 29 2 28, 29
Power supply circuit : Continuity should exist.
Signal circuit : Continuity should exist.
Ground circuit : Continuity should not exist.
Wheel Wheel sensor Ground Voltage
Front RH
1—8 V or more Front LH
Rear RH
Rear LH
SFIA3339E