Timing chain NISSAN TEANA 2003 Workshop Manual

TIMING CHAIN
EM-175
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

12. Obtain No. 1 cylinder at TDC of its compression stroke as follows:
a. Rotate crankshaft pulley clockwise to align timing mark (grooved
line without color) with timing indicator.
b. Make sure that intake and exhaust cam noses on No. 1 cylinder
(engine front side of right bank) are located as shown in the fig-
ure.

If not, turn crankshaft one revolution (360 degrees) and align
as shown in the figure.
13. Remove crankshaft pulley as follows:
a. Fix crankshaft with pulley holder (SST).
b. Loosen crankshaft pulley bolt and locate bolt seating surface at
10 mm (0.39 in) from its original position.
CAUTION:
Do not remove crankshaft pulley bolt as it will be used as a
supporting point for suitable puller.
c. Place suitable puller tab on holes of crankshaft pulley, and pull
crankshaft pulley through.
CAUTION:
Do not put suitable puller tab on crankshaft pulley periph-
ery, as this will damage internal damper.
14. Remove front timing chain case as follows:
SEM918G
SEM418G
PBIC2475E
SEM915E

EM-176
[VQ]
TIMING CHAIN

a. Loosen mounting bolts in the reverse order as shown in the fig-
ure.
b. Insert suitable tool into the notch at the top of front timing chain
case as shown (1).
c. Pry off case by moving tool as shown (2).

U s e s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] t o c u t l i q u i d g a s k e t f o r
removal.
CAUTION:

Do not use screwdrivers or something similar.

After removal, handle front timing chain case carefully so
it does not tilt, cant, or warp under a load.
15. Remove O-rings from rear timing chain case.
16. Remove water pump cover and chain tensioner cover from front timing chain case.

Use seal cutter [SST: KV10111100] to cut liquid gasket for removal.
17. Remove front oil seal from front timing chain case using suitable
tool.

Use screwdriver for removal.
CAUTION:
Be careful not to damage front timing chain case.
18. Remove timing chain tensioner (primary) as follows:
SEM730G
SEM156F
PBIC2548E
EMQ0032D

TIMING CHAIN
EM-177
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

a. Remove lower mounting bolt.
b. Loosen upper mounting bolt slowly, and then turn timing chain
tensioner (primary) on the mounting bolt so that plunger is fully
expanded.
NOTE:
Even if plunger is fully expanded, it is not dropped from the body
of timing chain tensioner (primary).
c. Remove upper mounting bolt, and then remove timing chain ten-
sioner (primary).
19. Remove internal chain guide, tension guide and slack guide.
NOTE:
Tension guide can be removed after removing timing chain (pri-
mary).
20. Remove timing chain (primary) and crankshaft sprocket.
CAUTION:
After removing timing chain (primary), do not turn crankshaft and camshaft separately, or valves
will strike the piston heads.
21. Remove timing chain (secondary) and camshaft sprockets as follows:
a. Attach suitable stopper pin to the right and left timing chain ten-
sioners (secondary).
NOTE:

Use approximately 0.5 mm (0.02 in) dia. hard metal pin as a
stopper pin.

For removal of timing chain tensioner (secondary), refer to
EM-192, "
CAMSHAFT" . [Removing camshaft bracket (No. 1)
is required.]
PBIC3562E
PBIC2266E
PBIC2047E

EM-178
[VQ]
TIMING CHAIN

b. Remove camshaft sprockets (INT and EXH) mounting bolts.

Secure the hexagonal portion of camshaft using wrench to
loosen mounting bolts.
CAUTION:
Do not loosen mounting bolts with securing anything
other than the camshaft hexagonal portion or with ten-
sioning the timing chain.
c. Remove timing chain (secondary) together with camshaft sprockets.

Turn camshaft slightly to secure slackness of timing chain on timing chain tensioner (secondary) side.

Insert 0.5 mm (0.020 in)-thick metal or resin plate between
timing chain and timing chain tensioner plunger (guide).
Remove timing chain (secondary) together with camshaft
sprockets with timing chain loose from guide groove.
CAUTION:
Be careful of plunger coming-off when removing timing
chain (secondary). This is because plunger of timing
chain tensioner (secondary) moves during operation,
leading to coming-off of fixed stopper pin.
NOTE:
Camshaft sprocket (INT) is two-for-one structure of sprockets
for timing chain (primary) and for timing chain (secondary).

When handling camshaft sprocket (INT), be careful of the fol-
lowing caution:
CAUTION:

Handle carefully to avoid any shock to camshaft
sprocket.

Do not disassemble. (Do not loosen bolts “A” as
shown in the figure).
22. Remove water pump. Refer to CO-46, "
WATER PUMP" .
23. Remove rear timing chain case as follows:
a. Loosen and remove mounting bolts in the reverse order as
shown in the figure.
b . C u t l i q u i d g a s k e t u s i n g s e a l c u t t e r [ S S T: K V 1 0 1111 0 0 ] a n d
remove rear timing chain case.
KBIA1698J
PBIC1978E
PBIC2980E
SEM735G

TIMING CHAIN
EM-179
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

CAUTION:

Do not remove plate metal cover of oil passage.

After removal, handle rear timing chain case carefully so
it does not tilt, cant, or warp under a load.
24. Remove O-rings from cylinder head.
25. Remove O-rings from cylinder block.
26. Remove timing chain tensioners (secondary) from cylinder head as follows, if necessary.
a. Remove camshaft brackets (No. 1). Refer to EM-192, "
REMOVAL" .
b. Remove timing chain tensioners (secondary) with stopper pin attached.
27. Use scraper to remove all traces of old liquid gasket from front
and rear timing chain cases, and opposite mating surfaces.
KBIA1307E
SBIA0496E
PBIC0788E
SEM737G

EM-180
[VQ]
TIMING CHAIN


Remove old liquid gasket from bolt hole and thread.
28. Use scraper to remove all traces of old liquid gasket from water
pump cover, chain tensioner cover and intake valve timing con-
trol covers.
INSPECTION AFTER REMOVAL
Timing Chain
Check for cracks and any excessive wear at link plates and roller
links of timing chain. Replace timing chain as necessary.
PBIC2084E
SEM926E
PBIC0282E

TIMING CHAIN
EM-181
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

INSTALLATION
NOTE:
The below figure shows the relationship between the mating mark on each timing chain and that on the corre-
sponding sprocket, with the components installed.
1. Install timing chain tensioners (secondary) to cylinder head as follows if removed. Refer to EM-197,
"INSTALLATION" .
a. Install timing chain tensioners (secondary) with stopper pin attached and new O-ring.
b. Install camshaft brackets (No. 1). Refer to EM-197, "
INSTALLATION" .
2. Install rear timing chain case as follows:
a. Install new O-rings onto cylinder block.
PBIC3590E
PBIC0788E

EM-182
[VQ]
TIMING CHAIN

b. Install new O-rings to cylinder head.
c. Apply liquid gasket with tube presser [SST: WS39930000] to rear timing chain case back side as shown in
the figure.
Use Genuine Liquid Gasket or equivalent.
CAUTION:

For “A” in the figure, completely wipe out liquid gasket extended on a portion touching at
engine coolant.

Apply liquid gasket on installation position of water pump and cylinder head very completely.
d. Align rear timing chain case and water pump assembly with dowel pins (right and left) on cylinder block
and install rear timing chain case.

Make sure O-rings stay in place during installation to cylinder block and cylinder head.
SBIA0496E
PBIC2616E

TIMING CHAIN
EM-183
[VQ]
C
D
E
F
G
H
I
J
K
L
MA
EM

e. Tighten mounting bolts in numerical order as shown in the fig-
ure.

There are two types of mounting bolt. Refer to the following
for locating bolts.
f. After all bolts tightening, retighten them to the specified in
numerical order as shown in the figure.

If liquid gasket protrudes, wipe it off immediately.
g. After installing rear timing chain case, check surface height dif-
ference between the following parts on the oil pan (upper)
mounting surface.

If not within standard, repeat the installation procedure.
3. Install water pump with new O-rings. Refer to CO-46, "
WATER PUMP" .
4. Make sure that dowel pin hole, dowel pin and crankshaft key are
located as shown in the figure. (No. 1 cylinder at compression
TDC)
NOTE:
Though camshaft does not stop at the position as shown in the
figure, for the placement of cam nose, it is generally accepted
camshaft is placed for the same direction of the figure.
CAUTION:
Hole on small dia. side must be used for intake side dowel pin hole. Do not misidentify (ignore big
dia. side).
5. Install timing chain (secondary) and camshaft sprockets (INT and EXH) as follows:
CAUTION:
Mating marks between timing chain and sprockets slip easily. Confirm all mating mark positions
repeatedly during the installation process.Bolt length: Bolt position
20 mm (0.79 in) : 1, 2, 3, 6, 7, 8, 9, 10
16 mm (0.63 in) : Except the above
: 12.7 N·m (1.3 kg-m, 9 ft-lb)
SEM735G
Standard
Rear timing chain case to cylinder block:
−0.24 to 0.14 mm (−0.009 to 0.006 in)
SEM943G
Camshaft dowel pin hole (intake side)
: At cylinder head upper face side in each bank
Camshaft dowel pin (exhaust side)
: At cylinder head upper face side in each bank
Crankshaft key
: At cylinder head side of right bank
KBIA1073E

EM-184
[VQ]
TIMING CHAIN

a. Push plunger of chain tensioner (secondary) and keep it
pressed in with stopper pin.
b. Install timing chain (secondary) and camshaft sprockets (INT
and EXH).

Align the mating marks on timing chain (secondary) (gold link)
with the ones on camshaft sprockets (INT and EXH)
(punched), and install them.
NOTE:

Mating marks for camshaft sprocket (INT) are on the back
side of camshaft sprocket (secondary).

There are two types of mating mark, circle and oval types.
They should be used for the right and left banks, respec-
tively.

Align dowel pin and pin hole on camshafts with the groove
and dowel pin on sprockets, and install them.

On the intake side, align pin hole on the small diameter side of
the camshaft front end with dowel pin on the back side of
camshaft sprocket, and install them.

On the exhaust side, align dowel pin on camshaft front end
with pin groove on camshaft sprocket, and install them.

In case that positions of each mating mark and each dowel
pin are not fit on mating parts, make fine adjustment to the position holding the hexagonal portion on
camshaft with wrench or equivalent.

Mounting bolts for camshaft sprockets must be tightened in the next step. Tightening them by hand is
enough to prevent the dislocation of dowel pins.

It may be difficult to visually check the dislocation of mating
marks during and after installation. To make the matching
easier, make a mating mark on the top of sprocket teeth and
its extended line in advance with paint.
SEM430G
Right bank : Use circle type.
Left bank : Use oval type.
PBIC2981E
PBIC0891E