k electrical NISSAN TEANA 2003 Repair Manual

CVT-30
TROUBLE DIAGNOSIS

CVT Electrical Parts LocationBCS001GH
SCIA7849E

CVT-48
TROUBLE DIAGNOSIS

A/T TCC S/V FNCTN

There is a big difference engine speed and primary speed when
TCM lock-up signal is on

CVT cannot perform lock-up even if electrical circuit is good

TCM detects as irregular by comparing difference value with slip
rotationP0744CVT-94
L/PRESS SOL/CIRC

Normal voltage not applied to solenoid due to open or short cir-
cuit

TCM detects as irregular by comparing target value with monitor
valueP0745CVT-97
PRS CNT SOL/A FCTNUnexpected gear ratio was detected in the LOW side due to exces-
sively low line pressureP0746CVT-102
PRS CNT SOL/B FCTNSecondary pressure is too high or too low compared with the com-
manded value while drivingP0776CVT-105
PRS CNT SOL/B CIRC

Normal voltage not applied to solenoid due to cut line, short, or
the like

TCM detects as irregular by comparing target value with monitor
valueP0778CVT-108
MANUAL MODE SWITCHWhen an impossible pattern of switch signals is detected, a mal-
function is detectedP0826CVT-113
TR PRS SENS/A CIRCSignal voltage of the transmission fluid pressure sensor A (second-
ary pressure sensor) is too high or too low while drivingP0840CVT-118
PRESS SEN/FNCTNCorrelation between the values of the transmission fluid pressure
sensor A (secondary pressure sensor) and the transmission fluid
pressure sensor B (primary pressure sensor) is out of specificationP0841CVT-123
TR PRS SENS/B CIRCSignal voltage of the transmission fluid pressure sensor B (primary
pressure sensor) is too high or too low while drivingP0845CVT-126
SEC/PRESS DOWNSecondary fluid pressure is too low compared with the commanded
value while drivingP0868CVT-131
TCM-POWER SUPPLY

When the power supply to the TCM is cut OFF, for example
because the battery is removed, and the self-diagnosis memory
function stops

This is not a malfunction message (Whenever shutting OFF a
power supply to the TCM, this message appears on the screen)P1701CVT-134
TP SEN/CIRC A/TTCM does not receive the proper accelerator pedal position signals
(input by CAN communication) from ECMP1705CVT-139
ESTM VEH SPD SIG

CAN communication with the ABS actuator and the electric unit
(control unit) is malfunctioning

There is a great difference between the vehicle speed signal from
the ABS actuator and the electric unit (control unit), and the vehi-
cle speed sensor signalP1722CVT-141
CVT SPD SEN/FNCTNA rotation sensor error is detected because the gear does not
change in accordance with the position of the stepping motor
CAUTION:
One of the “P0720 VEH SPD SEN/CIR AT”, the “P0715 INPUT
SPD SEN/CIRC” or the “P0725 ENGINE SPEED SIG” is dis-
played with the DTC at the same timeP1723CVT-143
ELEC TH CONTROL The electronically controlled throttle for ECM is malfunctioning P1726CVT-145
LU-SLCT SOL/CIRC

Normal voltage not applied to solenoid due to cut line, short, or
the like

TCM detects as irregular by comparing target value with monitor
valueP1740CVT-147
L/PRESS CONTROL TCM detects the unexpected line pressure P1745CVT-152
Items
(CONSULT-II screen terms)Malfunction is detected when...TCM self-
diagnosisReference
page
DTC

CVT-94
DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)

DTC P0744 A/T TCC S/V FUNCTION (LOCK-UP)PFP:31940
DescriptionBCS001IP
This malfunction is detected when the torque converter clutch does not lock-up as instructed by the TCM. This
is not only caused by electrical malfunction (circuits open or shorted), but also by mechanical malfunction such
as control valve sticking, improper solenoid valve operation, etc.
CONSULT-II Reference ValueBCS001IQ
Remarks: Specification data are reference values.
On Board Diagnosis LogicBCS001IR
Diagnostic trouble code “P0744 A/T TCC S/V FNCTN” with CONSULT-II is detected under the following condi-
tions.

When CVT cannot perform lock-up even if electrical circuit is good.

When TCM compares difference value with slip revolution and detects an irregularity.
Possible CauseBCS001IS

Torque converter clutch solenoid valve

Hydraulic control circuit
DTC Confirmation ProcedureBCS001IT
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, touch “ERASE” on “SELF-DIAG RESULTS” and then perform the following procedure to con-
firm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON. (Do not start engine.)
2. Select “DATA MONITOR” mode for “TRANSMISSION” with
CONSULT-II.
3. Start engine and maintain the following condition for at least 30
seconds.
ACC PEDAL OPEN: More than 1.0/8
RANGE: “D” position
[Vehicle speed: Constant speed of more than 40 km/h (25
MPH)]
4. If DTC is detected go to CVT-95, "
Diagnostic Procedure" .
Item name Condition Display value
ENG SPEED SIG Engine running Closely matches the tachometer reading
PRI SPEED SEN During driving (lock-up ON) Approximately matches the engine speed
BCIA0031E

CVT-108
DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRES-
SURE SOLENOID VALVE)

DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRESSURE
SOLENOID VALVE)
PFP:31941
DescriptionBCS001JF
The pressure control solenoid valve B (secondary pressure solenoid valve) regulates the oil pump discharge
pressure to suit the driving condition in response to a signal sent from the TCM.
CONSULT-II Reference ValueBCS001JG
Remarks: Specification data are reference values.
On Board Diagnosis LogicBCS001JH
Diagnostic trouble code “P0778 PRS CNT SOL/B CIRC” with CONSULT-II is detected under the following con-
ditions.

TCM detects an improper voltage drop when it tries to operate the solenoid valve.

When TCM compares target value with monitor value and detects an irregularity.
Possible CauseBCS001JI

Harness or connectors
(Solenoid circuit is open or shorted.)

Pressure control solenoid valve B (Secondary pressure solenoid valve)
DTC Confirmation ProcedureBCS001JJ
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON.
2. Select “DATA MONITOR” mode for “TRANSMISSION” with
CONSULT-II.
3. Start engine and wait at least 5 seconds.
4. If DTC is detected, go to CVT-110, "
Diagnostic Procedure" .
Item name Condition Display value (Approx.)
ISOLT3 Secondary pressure low - Secondary pressure high 0.8 - 0.0 A
SOLMON3“N” position idle 0.6 - 0.7 A
When stalled 0.4 - 0.6 A
BCIA0031E

DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRES-
SURE SOLENOID VALVE)
CVT-109
D
E
F
G
H
I
J
K
L
MA
B
CVT

Wiring Diagram — CVT — SECPSVBCS001JK
TCWM0538E

CVT-110
DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRES-
SURE SOLENOID VALVE)

TCM terminal data are reference values, measured between each terminal and ground.
Diagnostic ProcedureBCS001JL
1. CHECK INPUT SIGNAL
With CONSULT-II
1. Start engine.
2. Select “MAIN SIGNALS” in “DATA MONITOR” mode for
“TRANSMISSION” with CONSULT-II.
3. Read out the value of “ISOLT3”.
Without CONSULT-II
1. Start engine.
2. Check voltage between TCM connector terminal and ground.
3. Turn ignition switch OFF.
4. Disconnect TCM connector.
5. Check if there is continuity between connector terminal and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 2.
Terminal Wire color Item Condition Data (Approx.)
2W/BPressure control
solenoid valve B
(Secondary pres-
sure solenoid
valve)andRelease your foot from the accelerator pedal. 5.0 - 7.0 V
Press the accelerator pedal all the way down. 3.0 - 4.0 V
Item name Condition Display value (Approx.)
ISOLT3Secondary pressure low -
Secondary pressure high0.8 - 0.0 A
SCIA2349E
Name Connector Terminal ConditionVoltage
(Approx.)
Pressure
control
solenoid
valve B
(Second-
ary pres-
sure
solenoid
valve)F106 2 - groundRelease your foot from
the accelerator pedal.5.0 - 7.0 V
Press the accelerator
pedal all the way down.3.0 - 4.0 V
SCIA4506E

DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRES-
SURE SOLENOID VALVE)
CVT-111
D
E
F
G
H
I
J
K
L
MA
B
CVT

2. CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check resistance between TCM connector terminal and ground.
OK or NG
OK >> GO TO 5.
NG >> GO TO 3.
3. CHECK VALVE RESISTANCE
1. Turn ignition switch OFF.
2. Disconnect CVT unit harness connector.
3. Check resistance between CVT unit harness connector terminal
and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair or replace damaged parts.
4. CHECK HARNESS BETWEEN TCM AND PRESSURE CONTROL SOLENOID VALVE B (SECONDARY
PRESSURE SOLENOID VALVE)
1. Turn ignition switch OFF.
2. Disconnect TCM connector and CVT unit harness connector.
3. Check continuity between TCM connector terminal and CVT unit
harness connector terminal.
4. If OK, check harness for short to ground and short to power.
5. Reinstall any part removed.
OK or NG
OK >> GO TO 5.
NG >> Repair or replace damaged parts.
5. CHECK DTC
Perform “DTC Confirmation Procedure”. Refer to CVT-108, "
DTC Confirmation Procedure" .
OK or NG
OK >>INSPECTION END
NG >> GO TO 6.
Solenoid valve Connector TerminalResistance
(Approx.)
Pressure control solenoid
valve B (Secondary pres-
sure solenoid valve)F106 2 - Ground 3 - 9 Ω
SCIA4507E
Solenoid valve Connector TerminalResistance
(Approx.)
Pressure control sole-
noid valve B (Secondary
pressure solenoid valve) F49 3 - Ground 3 - 9 Ω
SCIA4688E
Item Connector Terminal Continuity
TCM connector F106 2
Ye s
CVT unit harness connector F49 3
SCIA4689E

CVT-112
DTC P0778 PRESSURE CONTROL SOLENOID B ELECTRICAL (SEC PRES-
SURE SOLENOID VALVE)

6. CHECK TCM
1. Check TCM input/output signal. Refer to CVT-40, "
TCM Input/Output Signal Reference Values" .
2. If NG, re-check TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK >>INSPECTION END
NG >> 1. Repair or replace damaged parts.
2. Replace the transaxle assembly. Refer to CVT-193, "
Removal and Installation" .
Component InspectionBCS001JM
PRESSURE CONTROL SORENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)
1. Turn ignition switch OFF.
2. Disconnect CVT unit harness connector.
3. Check resistance between CVT unit harness connector terminal
and ground.
4. If NG, replace the transaxle assembly. Refer to CVT-193,
"Removal and Installation" .
Solenoid Valve Connector TerminalResistance
(Approx.)
Pressure control sole-
noid valve B (Secondary
pressure solenoid valve) F49 3 - Ground 3 - 9 Ω
SCIA4688E

DTC P1778 STEP MOTOR - FUNCTION
CVT-157
D
E
F
G
H
I
J
K
L
MA
B
CVT

DTC P1778 STEP MOTOR - FUNCTIONPFP:31947
DescriptionBCS001M0

The step motor's 4 aspects of ON/OFF change according to the signal from TCM. As a result, the flow of
line pressure to primary pulley is changed and pulley ratio is controlled.

This diagnosis item is detected when electrical system is OK, but mechanical system is NG.

This diagnosis item is detected when the state of the changing the speed mechanism in unit does not
operate normally.
CONSULT-II Reference ValueBCS001M1
Remarks: Specification data are reference values.
On Board Diagnosis LogicBCS001M2
Diagnostic trouble code “P1778 STEP MOTR/FNC” with CONSULT-II is detected under the following condi-
tions.

When not changing the pulley ratio according to the instruction of TCM.
Possible CauseBCS001M3
Ste p mo to r
DTC Confirmation ProcedureBCS001M4
CAUTION:

Always drive vehicle at a safe speed.

Before starting “DTC Confirmation Procedure”, confirm “Hi” or “Mid” or “Low” fixation by “PRI
SPEED” and “VEHICLE SPEED” on “DATA MONITOR MODE”.

If hi-geared fixation occurred, go to CVT-158, "Diagnostic Procedure" .
NOTE:
If “DTC Confirmation Procedure” has been previously performed, always turn ignition switch OFF and
wait at least 10 seconds before performing the next test.
After the repair, touch “ERASE” on “SELF-DIAG RESULTS” and then perform the following procedure to con-
firm the malfunction is eliminated.
WITH CONSULT-II
1. Turn ignition switch ON and select “DATA MONITOR” mode for
“TRANSMISSION” with CONSULT-II.
2. Make sure that output voltage of CVT fluid temperature sensor
is within the range below.
ATF TEMP SEN: 1.0 - 2.0 V
If out of range, drive the vehicle to decrease the voltage
(warm up the fluid) or stop engine to increase the voltage
(cool down the fluid)
3. Select “DATA MONITOR” mode for “TRANSMISSION” with
CONSULT-II.
4. Start engine and maintain the following conditions for at least 30
consecutive seconds.
TEST START FROM 0 km/h (0 MPH)
CONSTANT ACCELERATION: Keep 30 sec or more
VEHICLE SPEED: 10 km/h (6 MPH) or more
ACC PEDAL OPEN: More than 1.0/8
RANGE: “D” position
ENG SPEED: 450 rpm or more
5. If DTC is detected, go to CVT-158, "
Diagnostic Procedure" .
Item name Condition Display value (Approx.)
STM STEP
During driving−20 step - 190 step
GEAR RATIO2.37 - 0.43
BCIA0031E

CVT-180
CVT SHIFT LOCK SYSTEM

CVT SHIFT LOCK SYSTEMPFP:00000
DescriptionBCS001MP

The electrical key interlock mechanism also operates as a shift lock:
With the ignition switch turned to ON, the selector lever cannot be shifted from “P” (parking) to any other
position unless the brake pedal is depressed.
With the key removed, the selector lever cannot be shifted from “P” to any other position.
The key cannot be removed unless the selector lever is placed in “P”.

The shift lock and key interlock mechanisms are controlled by the ON-OFF operation of the shift lock sole-
noid and by the operation of the rotator and slider located inside the key cylinder, respectively.
Shift Lock System Electrical Parts LocationBCS001MQ
NOTE:
This emergency lever can be used when battery is off ignition key cannot be removed. In the situation like this,
by operating this lever, ignition key can be removed.
1. Stop lamp switch 2. Shift lock control unit
A. Behind Audio Unit B. Key lock solenoid C. Emergency lever
D. Key switch E. Shift lock release button F. Detention switch (shift)
G. Detention switch (key) H. Shift lock solenoid
SCIA7845E