display NISSAN TEANA 2008 Service Manual

AV-172
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
FRONT DOOR SPEAKER
FRONT DOOR SPEAKER
Exploded ViewINFOID:0000000003940158
Removal and InstallationINFOID:0000000003940159
REMOVAL
1. Remove front door finisher. Refer to INT-30, "DRIVER SIDE : Removal and Installation" (driver side) or
INT-33, "
PASSENGER SIDE : Removal and Installation" (passenger side).
2. Remove front door speaker mounting bolts, disconnect the front door speaker connector.
3. Remove front door speaker.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1036ZZ
1. Front door speaker

AV
REAR DOOR SPEAKER
AV-173
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
REAR DOOR SPEAKER
Exploded ViewINFOID:0000000003940160
Removal and InstallationINFOID:0000000003940161
REMOVAL
1. Remove rear door finisher. Refer to INT-36, "Removal and Installation".
2. Remove rear door speaker mounting bolts, disconnect the rear door speaker connector.
3. Remove rear door speaker.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1037ZZ
1. Rear door speaker

AV-174
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
FRONT SQUAWKER
FRONT SQUAWKER
Exploded ViewINFOID:0000000003940162
Removal and InstallationINFOID:0000000003940163
REMOVAL
1. Remove the speaker grille with squawker. Refer to IP-12, "Removal and Installation".
2. Remove front squawker mounting screws, lift up the front squawker and disconnect front squawker con-
nector.
3. Remove front squawker.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1038ZZ
1. Front squawker

AV
ANTENNA AMP.
AV-175
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
ANTENNA AMP.
Exploded ViewINFOID:0000000003940164
Removal and InstallationINFOID:0000000003940165
REMOVAL
1. Remove rear side pillar finisher. Refer to INT-39, "Removal and Installation".
2. Disconnect antenna feeder connector and clip.
3. Remove antenna amp. mounting nut, disconnect the antenna amp. connector.
4. Remove antenna amp.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1032ZZ
1. AM-FM main connector
2. Antenna amp.

AV-176
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
MULTIFUNCTION SWITCH
MULTIFUNCTION SWITCH
Exploded ViewINFOID:0000000003940166
REMOVAL
Refer to IP-11, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940167
REMOVAL
1. Remove cluster lid D. Refer to IP-12, "Removal and Installation".
2. Remove multifunction switch mounting screws.
3. Remove multifunction switch.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1052ZZ
1. Cluster lid D
2. Multifunction switch

AV
PRESET SWITCH
AV-177
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
PRESET SWITCH
Exploded ViewINFOID:0000000003940168
REMOVAL
Refer to IP-11, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940169
REMOVAL
1. Remove cluster lid C. Refer to IP-12, "Removal and Installation".
2. Remove preset switch mounting screws.
3. Remove preset switch.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
When installing preset switch, do not allow the print wire that connects preset switch and multifunction switch
to get caught in between AV control unit and preset switch.
1. Preset switch 2. Cluster lid C
JPNIA1044ZZ
1. Preset switch
A. Screw
B. Screw
JPNIA1045ZZ

AV-178
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
REAR CONTROL SWITCH
REAR CONTROL SWITCH
Exploded ViewINFOID:0000000003940170
REMOVAL
Refer to SE-98, "Exploded View".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940171
REMOVAL
1. Remove rear control switch, stretching pawls of armrest assembly.
2. Disconnect rear control switch connector.
3. Remove rear control switch.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1046ZZ
1. Rear control switch
A. Clip

AV
AUXILIARY INPUT JACKS
AV-179
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
AUXILIARY INPUT JACKS
Exploded ViewINFOID:0000000003940172
REMOVAL
Refer to IP-22, "Removal and Installation".
DISASSEMBLY
Removal and InstallationINFOID:0000000003940173
REMOVAL
1. Remove console finisher. Refer to IP-22, "Removal and Installation".
2. Remove auxiliary mounting screws.
3. Remove auxiliary input jacks.
INSTALLATION
Installation is the reverse order of removal.
JPNIA1048ZZ
1. Auxiliary input jacks

AV-180
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
CAMERA CONTROL UNIT
CAMERA CONTROL UNIT
Exploded ViewINFOID:0000000003940174
Removal and InstallationINFOID:0000000003940175
REMOVAL
1. Remove rear wheelhouse finisher RH. Refer to INT-57, "Removal and Installation".
2. Remove camera control unit mounting screws, disconnect the camera control unit connector.
3. Remove camera control unit.
INSTALLATION
1. Installation is the reverse order of removal.
2. Perform predicted course line center position adjustment. Refer to AV-47, "
PREDICTED COURSE LINE
CENTER POSITION ADJUSTMENT : Special Repair Requirement".
JPNIA1049ZZ
1. Camera control unit

AV
REAR VIEW CAMERA
AV-181
< ON-VEHICLE REPAIR >[BASE AUDIO AND DISPLAY SYSTEM]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
REAR VIEW CAMERA
Exploded ViewINFOID:0000000003940176
DISASSEMBLY
Removal and InstallationINFOID:0000000003940177
REMOVAL
1. Remove trunk lid finisher inner. Refer to INT-59, "Removal and Installation".
2. Remove trunk lid finisher. Refer to EXT-38, "
Removal and Installation".
3. Remove rear view camera mounting clip, disconnect the rear view camera connector.
4. Remove rear view camera.
INSTALLATION
1. Installation is the reverse order of removal.
AdjustmentINFOID:0000000003970920
Adjust the guide line position if the guide line position is shifted after installing the rear view camera.
1. Draw lines on rearward area of the vehicle passing through the
following points: 200 mm (7.87 in) from both sides of the vehicle,
and 0.5 m (1.64 ft), 1.0 m (3.28 ft) from the rear end of the
bumper.
2. Set into “Adjust offset of rear view camera” mode of Confirma-
tion / Adjustment mode.
JPNIA1050ZZ
1. Rear view camera
2. Seal
Refer to GI-4, "
Components" for symbols in the figure.
SKIB3691E