brake sensor NISSAN TEANA 2008 User Guide

BRC-4
Diagnosis Procedure .............................................112
Special Repair Requirement ..................................112
C1145, C1146 YAW RATE/SIDE G SENSOR .113
Description .............................................................113
DTC Logic ..............................................................113
Diagnosis Procedure .............................................113
Component Inspection ...........................................114
Special Repair Requirement ..................................115
C1155 BRAKE FLUID LEVEL SWITCH ..........116
Description .............................................................116
DTC Logic ..............................................................116
Diagnosis Procedure .............................................116
Component Inspection ...........................................117
Special Repair Requirement ..................................117
C1164, C1165 CV SYSTEM ............................118
Description .............................................................118
DTC Logic ..............................................................118
Diagnosis Procedure .............................................118
Component Inspection ...........................................119
Special Repair Requirement ..................................119
C1166, C1167 SV SYSTEM .............................120
Description .............................................................120
DTC Logic ..............................................................120
Diagnosis Procedure .............................................120
Component Inspection ...........................................121
Special Repair Requirement ..................................121
U1000, U1002 CAN COMM CIRCUIT .............122
Description .............................................................122
DTC Logic ..............................................................122
Diagnosis Procedure .............................................122
Special Repair Requirement ..................................122
POWER SUPPLY AND GROUND CIRCUIT ...123
Description .............................................................123
Diagnosis Procedure .............................................123
PARKING BRAKE SWITCH ............................124
Component Function Check ..................................124
Diagnosis Procedure .............................................124
Component Inspection ...........................................124
VDC OFF SWITCH ..........................................126
Description .............................................................126
Component Function Check ..................................126
Diagnosis Procedure .............................................126
Component Inspection ...........................................127
ABS WARNING LAMP ....................................128
Description .............................................................128
Component Function Check ..................................128
Diagnosis Procedure .............................................128
BRAKE WARNING LAMP ...............................129
Description .............................................................129
Component Function Check ..................................129
Diagnosis Procedure .............................................129
VDC OFF INDICATOR LAMP ..........................130
Description ............................................................130
Component Function Check .................................130
Diagnosis Procedure .............................................130
SLIP INDICATOR LAMP ..................................131
Description ............................................................131
Component Function Check .................................131
Diagnosis Procedure .............................................131
ECU DIAGNOSIS ......................................132
ABS ACTUATOR AND ELECTRIC UNIT
(CONTROL UNIT) .............................................
132
Reference Value ...................................................132
Wiring Diagram - BRAKE CONTROL SYSTEM - .136
Fail-Safe ................................................................139
DTC No. Index ......................................................140
SYMPTOM DIAGNOSIS ...........................142
EXCESSIVE ABS FUNCTION OPERATION
FREQUENCY ....................................................
142
Diagnosis Procedure .............................................142
UNEXPECTED PEDAL REACTION .................143
Diagnosis Procedure .............................................143
THE BRAKING DISTANCE IS LONG ..............144
Diagnosis Procedure .............................................144
ABS FUNCTION DOES NOT OPERATE .........145
Diagnosis Procedure .............................................145
PEDAL VIBRATION OR ABS OPERATION
SOUND OCCURS .............................................
146
Diagnosis Procedure .............................................146
VEHICLE JERKS DURING VDC/TCS/ABS
CONTROL ........................................................
147
Diagnosis Procedure .............................................147
NORMAL OPERATING CONDITION ...............148
Description ............................................................148
PRECAUTION ...........................................149
PRECAUTIONS ................................................149
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
149
Precaution for Procedure without Cowl Top Cover .149
Precaution for Brake System ................................149
Precaution for Brake Control .................................150
Precautions for Harness Repair ............................150
ON-VEHICLE REPAIR ..............................151
WHEEL SENSOR .............................................151
FRONT WHEEL SENSOR ......................................151
FRONT WHEEL SENSOR : Exploded View .........151

BRC-10
< FUNCTION DIAGNOSIS >[ABS]
ABS
Component Parts Location
INFOID:0000000003766724
Component DescriptionINFOID:0000000003766725
1. ABS warning lamp 2. Brake warning lamp 3.ABS actuator and electric unit (con-
trol unit)
4. Front wheel sensor 5. Rear wheel sensor
A. Combination meter B. Engine room right side C. Steering knuckle
D. Rear axle
JSFIA0258ZZ
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-25, "
Description"Motor
Actuator relay (main relay)BRC-36, "
Description"
Solenoid valveBRC-32, "Description"
Wheel sensorBRC-16, "Description"
ABS warning lampBRC-40, "Description"
Brake warning lampBRC-41, "Description"

BRC-12
< FUNCTION DIAGNOSIS >[ABS]
EBD
Component Parts Location
INFOID:0000000003767310
Component DescriptionINFOID:0000000003767311
1. ABS warning lamp 2. Brake warning lamp 3.ABS actuator and electric unit (con-
trol unit)
4. Front wheel sensor 5. Rear wheel sensor
A. Combination meter B. Engine room right side C. Steering knuckle
D. Rear axle
JSFIA0258ZZ
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-25, "
Description"Motor
Actuator relay (main relay)BRC-36, "
Description"
Solenoid valveBRC-32, "Description"
Wheel sensorBRC-16, "Description"
ABS warning lampBRC-40, "Description"
Brake warning lampBRC-41, "Description"

DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
BRC-13
< FUNCTION DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
DIAGNOSIS SYSTEM [ABS ACTUATOR AND ELECTRIC UNIT (CONTROL
UNIT)]
CONSULT-III FunctionINFOID:0000000003766730
FUNCTION
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
SELF DIAGNOSTIC RESULT
Operation Procedure
Before performing the self-diagnosis, start engine and drive vehicle at 30 km/h (19 MPH) or more for approxi-
mately 1 minute.
Display Item List
Refer to BRC-48, "DTC No. Index".
How to Erase Self-diagnosis Results
After erasing DTC memory, start the engine and drive the vehicle at 30 km/h (19 MPH) or more for approxi-
mately 1 minute as the final inspection, and make sure that the ABS warning lamp and brake warning lamp
turn OFF.
CAUTION:
If memory cannot be erased, perform applicable diagnosis.
NOTE:
 When the wheel sensor malfunctions, after inspecting the wheel sensor system, ABS warning lamp and
brake warning lamp will not turn OFF even when the system is normal unless the vehicle is driven at approx-
imately 30 km/h (19 MPH) or more for approximately 1 minute.
 Brake warning lamp will turn ON in case of parking brake operation (when switch is ON) or in case of brake
fluid level switch operation (when brake fluid is insufficient).
DATA MONITOR
Display Item List
×: Applicable : Optional item
Diagnostic test mode Function
Self diagnostic result Self-diagnostic results can be read and erased quickly.
Data monitor Input/Output data in the ABS actuator and electric unit (control unit) can be read.
Active testCONSULT-III drives some actuators apart from ABS actuator and electric unit (control unit) and
also shifts some parameters in a specified range.
ECU identification ABS actuator and electric unit (control unit) part number can be read.
Monitor item (Unit)SELECT MONITOR ITEM
Remarks
ECU INPUT
SIGNALSMAIN SIGNALS
FR LH SENSOR
[km/h (MPH)]××Wheel speed calculated by front LH wheel sensor signal
FR RH SENSOR
[km/h (MPH)]××Wheel speed calculated by front RH wheel sensor signal
RR LH SENSOR
[km/h (MPH)]××Wheel speed calculated by rear LH wheel sensor signal
RR RH SENSOR
[km/h (MPH)]××Wheel speed calculated by rear RH wheel sensor signal
STOP LAMP SW
(On/Off)××Stop lamp switch signal status
BATTERY VOLT
(V)××Battery voltage supplied to the ABS actuator and electric
unit (control unit)

BRC-42
< ECU DIAGNOSIS >[ABS]
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
ECU DIAGNOSIS
ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Reference ValueINFOID:0000000003766848
VALUES ON THE DIAGNOSIS TOOL
CAUTION:
The display shows the control unit calculation data, so a normal value might be displayed even in the
event the output circuit (harness) is open or short-circuited.
Monitor item Display contentData monitor
ConditionReference value in
normal operation
FR LH SENSORWheel sensor calculated by front LH
wheel sensor signal is displayedVehicle stopped 0 [km/h (MPH)]
Vehicle running
(Note 1)Nearly matches the
speedometer dis-
play (± 10% or less)
FR RH SENSORWheel sensor calculated by front RH
wheel sensor signal is displayedVehicle stopped 0 [km/h (MPH)]
Vehicle running
(Note 1)Nearly matches the
speedometer dis-
play (± 10% or less)
RR LH SENSORWheel sensor calculated by rear LH
wheel sensor signal is displayedVehicle stopped 0 [km/h (MPH)]
Vehicle running
(Note 1)Nearly matches the
speedometer dis-
play (± 10% or less)
RR RH SENSORWheel sensor calculated by rear RH
wheel sensor signal is displayedVehicle stopped 0 [km/h (MPH)]
Vehicle running
(Note 1)Nearly matches the
speedometer dis-
play (± 10% or less)
STOP LAMP SW Stop lamp switch signal statusWhen brake pedal is depressed On
When brake pedal is not depressed Off
BATTERY VOLTBattery voltage supplied to the ABS ac-
tuator and electric unit (control unit)Ignition switch ON 10 – 16 V
FR RH IN SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
FR RH OUT SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
FR LH IN SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off
FR LH OUT SOLOperation status of each solenoid
valve Actuator (solenoid valve) is active (“AC-
TIVE TEST” with CONSULT-III)On
When the actuator (solenoid valve) is not
active and actuator relay is active (igni-
tion switch ON)Off

EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
BRC-49
< SYMPTOM DIAGNOSIS >[ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
SYMPTOM DIAGNOSIS
EXCESSIVE ABS FUNCTION OPERATION FREQUENCY
Diagnosis ProcedureINFOID:0000000003766852
1.CHECK START
Check front and rear brake force distribution using a brake tester. Refer to BR-45, "
General Specifications".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Check brake system.
2.CHECK FRONT AND REAR AXLE
Make sure that there is no excessive play in the front and rear axles.
 Front: Refer to FA X - 6 , "
Inspection".
 Rear: Refer to RAX-3, "
Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace malfunctioning components.
3.CHECK WHEEL SENSOR AND SENSOR ROTOR
Check the following.
 Wheel sensor installation for damage.
 Sensor rotor installation for damage.
 Wheel sensor connector connection.
 Wheel sensor harness inspection.
Is the inspection result normal?
YES >> GO TO 4.
NO >>  Replace wheel sensor or sensor rotor.
 Repair harness.
4.CHECK ABS WARNING LAMP DISPLAY
Make sure that the ABS warning lamp is turned off after the ignition switch is turned ON or when driving.
Is the ABS warning lamp illuminated?
YES >> Perform self-diagnosis.
NO >> Normal

BRC-68
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
VDC
FUNCTION DIAGNOSIS
VDC
System DiagramINFOID:0000000003766885
System DescriptionINFOID:0000000003766886
 Vehicle Dynamics Control system detects driver′s steering operation amount and brake pedal travel from
steering angle sensor and pressure sensor. Using information from yaw rate/side G sensor and wheel sen-
sor, VDC judges driving condition (conditions of under steer and over steer) to improve vehicle driving stabil-
ity by controlling brake application to 4 wheels and engine output.
 During VDC operation, it informs driver of system operation by flashing SLIP indicator lamp.
 Electrical system diagnosis by CONSULT-III is available.
JSFIA0259GB

VDC
BRC-69
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
Component Parts LocationINFOID:0000000003766887
1. Steering angle sensor 2. ABS warning lamp 3. Brake warning lamp
4. VDC OFF indicator lamp 5. SLIP indicator lamp 6. Yaw rate/side G sensor
7. ABS actuator and electric unit (con-
trol unit)8. Front wheel sensor 9. VDC OFF switch
10. Rear wheel sensor
JSFIA0260ZZ

BRC-70
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
VDC
Component Description
INFOID:0000000003766888
A. Back of spiral cable assembly B. Combination meter C. Under center console
D. Engine room right side E. Steering knuckle F. Instrument driver lower panel
G. Rear axle
Component parts Reference
ABS actuator and electric unit (control unit)Pump
BRC-94, "
Description"Motor
Actuator relay (main relay)BRC-106, "
Description"
Solenoid valveBRC-101, "Description"
Pressure sensorBRC-108, "Description"
VDC switch-over valve (USV1, USV2)BRC-118, "Description"
VDC switch-over valve (HSV1, HSV2)BRC-120, "Description"
Wheel sensorBRC-85, "Description"
Yaw rate/side G sensorBRC-113, "Description"
Steering angle sensorBRC-110, "Description"
VDC OFF switchBRC-126, "Description"
ABS warning lampBRC-128, "Description"
Brake warning lampBRC-129, "Description"
VDC OFF indicator lampBRC-130, "Description"
SLIP indicator lampBRC-131, "Description"

TCS
BRC-71
< FUNCTION DIAGNOSIS >[VDC/TCS/ABS]
C
D
E
G
H
I
J
K
L
MA
B
BRC
N
O
P
TCS
System DiagramINFOID:0000000003767312
System DescriptionINFOID:0000000003766890
 Traction Control System is a function that electronically controls engine torque, brake fluid pressure and
CVT shift position to ensure the optimum slippage ratio at drive wheels by computing wheel speed signals
from 4 wheel sensors. When ABS actuator and electric unit (control unit) detects a spin at drive wheels (rear
wheels), it compares wheel speed signals from all 4 wheels. At this time, LH and RH rear brake fluid pres-
sure are controlled, while fuel being cut to engine and throttle valve being closed to reduce engine torque by
the control unit. Further more, throttle position is continuously controlled to ensure the optimum engine
torque at all times.
 During TCS operation, TCS informs driver of system operation by flashing SLIP indicator lamp.
 Electrical system diagnosis by CONSULT-III is available.
JSFIA0259GB