Int NISSAN TEANA 2008 Owner's Manual

ADP-40
< COMPONENT DIAGNOSIS >
B2130 EEPROM
B2130 EEPROM
DTC LogicINFOID:0000000003759101
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.STEP 1
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
Is the DTC detected?
YES >> Refer to ADP-40, "DiagnosisProcedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003759102
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Erase the DTC.
4. Perform DTC confirmation procedure. Refer to ADP-40, "
DTC Logic".
Is the DTC displayed again?
YES >> GO TO 2.
NO >> Check intermittent incident. Refer to GI-35, "
Intermittent Incident".
2.REPLACE DRIVER SEAT CONTROL UNIT
Replace driver seat control unit. Refer to ADP-136, "
Removal and Installation".
>> INSPECTION END
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B2130 EEPROM Driver seat control unit detected CPU malfunction Driver seat control unit

ADP-42
< COMPONENT DIAGNOSIS >
B2112 SLIDING MOTOR
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace driver seat control unit. Refer to ADP-136, "
Removal and Installation"
4.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
(+)
(–)Voltage (V)
(Approx.) Driver seat control unit
Connector Terminal
B4513
Ground 0
4

ADP-44
< COMPONENT DIAGNOSIS >
B2113 RECLINING MOTOR
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace driver seat control unit. Refer to ADP-136, "
Removal and Installation".
4.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
(+)
(–)Voltage (V)
(Approx.) Driver seat control unit
Connector Terminal
B4515
Ground 0
6

SLIDING SWITCH
ADP-47
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
Is the inspection result normal?
YES >> Replace driver seat control unit. Refer to ADP-136, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK SLIDING SWITCH
Refer to ADP-47, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace power seat switch (driver side). Refer to ADP-138, "
Removal and Installation"
4.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000003759122
1.CHECK SLIDING SWITCH
1. Turn ignition switch OFF.
2. Disconnect power seat switch (driver side) connector.
3. Check continuity between power seat switch (driver side) terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch (driver side). Refer to ADP-138, "
Removal and Installation".
Power seat switch (driver side)
Condition Continuity
Te r m i n a l
3611 Sliding switch (backward)Operate Existed
Release Not existed
12 Sliding switch (forward)Operate Existed
Release Not existed

RECLINING SWITCH
ADP-49
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
Is the inspection result normal?
YES >> Replace driver seat control unit. Refer to ADP-136, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK RECLINING SWITCH
Refer to ADP-49, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace power seat switch (driver side). Refer to ADP-138, "
Removal and Installation".
4.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000003759126
1.CHECK RECLINING SWITCH
1. Turn ignition switch OFF.
2. Disconnect power seat switch (driver side) connector.
3. Check continuity between power seat switch (driver side) terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch (driver side). Refer to ADP-138, "
Removal and Installation".
Power seat switch (driver side)
Condition Continuity
Te r m i n a l
3613 Reclining switch (backward)Operate Existed
Release Not existed
14 Reclining switch (forward)Operate Existed
Release Not existed

LIFTING SWITCH (FRONT)
ADP-51
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
Is the inspection result normal?
YES >> Replace driver seat control unit. Refer to ADP-136, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK LIFTING SWITCH (FRONT)
Refer to ADP-51, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace power seat switch (driver side). Refer to ADP-138, "
Removal and Installation".
4.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000003759130
1.CHECK LIFTING SWITCH (FRONT)
1. Turn ignition switch OFF.
2. Disconnect power seat switch (driver side) connector.
3. Check continuity between power seat switch (driver side) terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch (driver side). Refer to ADP-138, "
Removal and Installation".
Power seat switch (driver side)
Condition Continuity
Te r m i n a l
3617 Lifting switch front (down)Operate Existed
Release Not existed
18 Lifting switch front (up)Operate Existed
Release Not existed

LIFTING SWITCH (REAR)
ADP-53
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
Is the inspection result normal?
YES >> Replace driver seat control unit. Refer to ADP-136, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK LIFTING SWITCH (REAR)
Refer to ADP-53, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace power seat switch (driver side) . Refer to ADP-138, "
Removal and Installation".
4.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000003759134
1.CHECK LIFTING SWITCH (REAR)
1. Turn ignition switch OFF.
2. Disconnect power seat switch (driver side) connector.
3. Check continuity between power seat switch (driver side) terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace power seat switch (driver side). Refer to ADP-138, "
Removal and Installation".
Power seat switch (driver side)
Condition Continuity
Te r m i n a l
3615 Lifting switch rear (down)Operate Existed
Release Not existed
16 Lifting switch rear (up)Operate Existed
Release Not existed

SEAT MEMORY SWITCH
ADP-55
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
4. Check continuity between driver seat control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace driver seat control unit. Refer to ADP-136, "Removal and Installation".
NO >> Repair or replace harness.
4.CHECK SEAT MEMORY SWITCH
Refer to ADP-55, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace seat memory switch. Refer to ADP-137, "
Removal and Installation".
5.CHECK MEMORY SWITCH GROUND CIRCUIT
Check continuity between seat memory switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000003759146
1.CHECK SEAT MEMORY SWITCH
1. Turn ignition switch OFF.
2. Disconnect seat memory switch connector.
3. Check continuity between seat memory switch terminals.
Driver seat control unit Seat memory switch
Continuity
Connector Terminal Connector Terminal
B45227
D131
Existed 28 2
29 3
Driver seat control unit
GroundContinuity
Connector Terminal
B45227
Not existed 28
29
Seat memory switch
GroundContinuity
Connector Terminal
D13 4 Existed

FRONT DOOR SWITCH (DRIVER SIDE)
ADP-59
< COMPONENT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
MA
B
ADP
N
O
P
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-78, "Removal and Installation".
NO >> Repair or replace harness.
3.CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Refer to ADP-59, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace front door switch (driver side). Refer to DLK-234, "
Removal and Installation"
4.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000003759160
1.CHECK FRONT DOOR SWITCH (DRIVER SIDE)
1. Turn ignition switch OFF.
2. Disconnect front door switch (driver side) connector.
3. Check continuity between front door switch (driver side) terminals.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace front door switch (driver side). Refer to DLK-234, "
Removal and Installation".
Te r m i n a l
Condition Continuity
Front door switch (driver side)
2Ground part of door
switchFront door switch
(driver side)Press Not existed
Release Existed

ADP-78
< COMPONENT DIAGNOSIS >
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE)
Reference ValueINFOID:0000000003940046
VALUES ON THE DIAGNOSIS TOOL
CONSULT-III MONITOR ITEM
Monitor Item Condition Value/Status
FR WIPER HIOther than front wiper switch HI Off
Front wiper switch HI On
FR WIPER LOWOther than front wiper switch LO Off
Front wiper switch LO On
FR WASHER SWFront washer switch OFF Off
Front washer switch ON On
FR WIPER INTOther than front wiper switch INT Off
Front wiper switch INT On
FR WIPER STOPFront wiper is not in STOP position Off
Front wiper is in STOP position On
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 Wiper intermittent dial position
TURN SIGNAL ROther than turn signal switch RH Off
Turn signal switch RH On
TURN SIGNAL LOther than turn signal switch LH Off
Turn signal switch LH On
TAIL LAMP SWOther than lighting switch 1ST and 2ND Off
Lighting switch 1ST or 2ND On
HI BEAM SWOther than lighting switch HI Off
Lighting switch HI On
HEAD LAMP SW 1Other than lighting switch 2ND Off
Lighting switch 2ND On
HEAD LAMP SW 2Other than lighting switch 2ND Off
Lighting switch 2ND On
PASSING SWOther than lighting switch PASS Off
Lighting switch PASS On
AUTO LIGHT SWOther than lighting switch AUTO Off
Lighting switch AUTO On
FR FOG SWFront fog lamp switch OFF Off
Front fog lamp switch ON On
RR FOG SWRear fog lamp switch OFF Off
Rear fog lamp switch ON On
DOOR SW-DRDriver door closed Off
Driver door opened On
DOOR SW-ASPassenger door closed Off
Passenger door opened On
DOOR SW-RRRear RH door closed Off
Rear RH door opened On
DOOR SW-RLRear LH door closed Off
Rear LH door opened On