lock NISSAN TEANA 2008 Service Manual

PRECAUTIONS
TM-137
< PRECAUTION >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
Rotate bayonet ring counterclockwise. Pull out CVT unit harness
connector upward and remove it.
INSTALLATION
1. Align ∆ marking on CVT unit harness connector terminal body
with o marking on bayonet ring. Insert CVT unit harness connec-
tor. Then rotate bayonet ring clockwise.
2. Rotate bayonet ring clockwise until ∆ marking on CVT unit har-
ness connector terminal body is aligned with the slit on bayonet
ring as shown in the figure (correctly fitting condition). Install
CVT unit harness connector to CVT unit harness connector ter-
minal body.
CAUTION:
 Securely align ∆ marking on CVT unit harness connector
terminal body with bayonet ring slit. Then, be careful not
to make a half fit condition as shown in the figure.
 Never mistake the slit of bayonet ring for other dent por-
tion.
SCIA2096E
SCIA2097E
SCIA2098E
SCIA2099E

PRECAUTIONS
TM-139
< PRECAUTION >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
Always perform the procedure on TM-35, "Diagnosis Description" to complete the repair and avoid
unnecessary blinking of the MI.
For details of OBD, refer to EC-102, "
Diagnosis Description".
Certain systems and components, especially those related to OBD, may use the new style slide-lock-
ing type harness connector. For description and how to disconnect, refer to PG-96
.
ATFTEMP COUNT Conversion Table INFOID:0000000003849073
ATFTEMP COUNT Temperature °C (°F) ATFTEMP COUNT Temperature °C (°F)
4 –30 (–22) 177 90 (194)
8 –20 (–4) 183 95 (203)
13 –10 (14) 190 100 (212)
17 –5 (23) 196 105 (221)
21 0 (32) 201 110 (230)
27 5 (41) 206 115 (239)
32 10 (50) 210 120 (248)
39 15 (59) 214 125 (257)
47 20 (68) 218 130 (266)
55 25 (77) 221 135 (275)
64 30 (86) 224 140 (284)
73 35 (95) 227 145 (293)
83 40 (104) 229 150 (302)
93 45 (113) 231 155 (311)
104 50 (122) 233 160 (320)
114 55 (131) 235 165 (329)
124 60 (140) 236 170 (338)
134 65 (149) 238 175 (347)
143 70 (158) 239 180 (356)
152 75 (167) 241 190 (374)
161 80 (176) 243 200 (392)
169 85 (185) — —

TM-142
< ON-VEHICLE MAINTENANCE >[CVT: RE0F09B]
CVT FLUID
ON-VEHICLE MAINTENANCE
CVT FLUID
InspectionINFOID:0000000003849076
CHECKING CVT FLUID
The fluid level should be checked with the fluid warmed up to 50 to 80°C (122 to 176°F). The fluid level check
procedure is as follows:
1. Check for fluid leakage.
2. With the engine warmed up, drive the vehicle in an urban area.
When ambient temperature is 20°C (68°F), it takes about 10
minutes for the CVT fluid to warm up to 50 to 80°C (122 to
176°F).
3. Park the vehicle on a level surface.
4. Apply parking brake firmly.
5. With engine at idle, while depressing brake pedal, move shift
selector throughout the entire shift range.
6. Pull out the CVT fluid level gauge from the CVT fluid charging
pipe after pressing the tab on the CVT fluid level gauge to
release the lock.
7. Wipe fluid off the CVT fluid level gauge. Insert the CVT fluid
level gauge rotating 180° from the originally installed position,
then securely push the CVT fluid level gauge until it meets the
top end of the CVT fluid charging pipe.
CAUTION:
When wiping away the CVT fluid level gauge, always use
lint-free paper, not a cloth rag.
8. Place the selector lever in “P” or “N” and check that the fluid
level is within the specified range.
CAUTION:
When reinstalling CVT fluid level gauge, insert it into the
CVT fluid charging pipe and rotate it to the original installa-
tion position until securely locked.
CVT FLUID CONDITION
SMA146B
SCIA1933E
SCIA1931E
SCIA1932E

TM-148
< ON-VEHICLE MAINTENANCE >[CVT: RE0F09B]
ROAD TEST
ROAD TEST
DescriptionINFOID:0000000003849080
DESCRIPTION
 The purpose of the test is to determine the overall performance of
CVT and analyze causes of problems.
 The road test consists of the following three parts:
1. “Check Before Engine Is Started” TM-148
.
2. “Check at Idle” TM-149
.
3. “Cruise Test” TM-150
.
 Before the road test, familiarize yourself with all test procedures
and items to check.
 Perform tests for all the check items until a malfunction phenome-
non is detected. Perform diagnosis for NG items after the comple-
tion of road tests.
CONSULT-III SETTING PROCEDURE
 Using CONSULT-III, perform a cruise test and record the result.
 Print the result and ensure that shifts and lock-ups take place as per Shift Schedule.
1. Touch “Data Monitor” on “Direct Diagnostic Mode” screen.
2. Touch “MAIN SIGNALS” to set recording condition.
3. See “Numerical Display”, “Barchart Display” or “Line Graph Display”.
4. Touch “START”.
5. When performing cruise test. Refer to TM-150, "
Cruise Test".
6. After finishing cruise test part, touch “RECORD”.
7. Touch “STORE”.
8. Touch “BACK”.
9. Touch “DISPLAY”.
10. Touch “PRINT”.
11. Check the monitor data printed out.
Check before Engine Is StartedINFOID:0000000003849081
1.CHECK SPORT INDICATOR LAMP
1. Park vehicle on flat surface.
2. Move selector lever to “P” position.
3. Turn ignition switch OFF. Wait at least 5 seconds.
4. Turn ignition switch ON. (Do not start engine.)
Has SPORT indicator lamp been turned ON for about 2 seconds?
YES >> 1. Turn ignition switch OFF.
2. Perform self-diagnosis and note NG items. Refer to TM-121, "
DTC Index".
3. Go to TM-149, "
Check at Idle".
NO >> Stop “Road Test”. Refer to TM-123, "
Symptom Table".
SAT786A
SAT496G

TM-152
< ON-VEHICLE MAINTENANCE >[CVT: RE0F09B]
CVT POSITION
CVT POSITION
Inspection and AdjustmentINFOID:0000000003849084
INSPECTION
1. Move selector lever to “P” position, and turn ignition switch ON (engine stop).
2. Check that selector lever can be shifted to other than “P” position when brake pedal is depressed. Also
check that selector lever can be shifted from “P” position only when brake pedal is depressed.
3. Move selector lever and check for excessive effort, sticking, noise or rattle.
4. Check that selector lever stops at each position with the feel of engagement when it is moved through all
the positions. Check that the actual position of selector lever matches the position shown by shift position
indicator and manual lever on the transaxle.
5. The method of operating selector lever to individual positions
correctly should be as shown.
6. When selector button is pressed in “P”, “R”, “N”, “D” or “L” posi-
tion without applying forward/backward force to selector lever,
check button operation for sticking.
7. Check that back-up lamps illuminate only when selector lever is
placed in the “R” position.
8. When in “R” position, check that back-up lamps illuminate even
when the selector lever is pushed toward the “P” position.
CAUTION:
Check the lighting without pressing shift button.
9. Check that back-up lamps do not illuminate when selector lever is pushed toward the “R” position when in
the “P” or “N” position.
CAUTION:
Check the lighting without pressing shift button.
10. Check that the engine can only be started with selector lever in the “P” and “N” positions.
11. Check that transaxle is locked completely in “P” position.
ADJUSTMENT
1. Move selector lever to “ P” position.
CAUTION:
Turn wheels more than 1/4 rotations and apply the park
lock.
2. Loosen the control cable nut (A).
3. Place manual lever (B) to “P” position.
CAUTION:
Never apply any force to manual lever.
4. Tighten the control cable nut. Refer to TM-157, "
Exploded View".
CAUTION:
Fix manual lever when tightening.
JPDIA0343GB
JPDIA0794ZZ

CONTROL DEVICE
TM-155
< ON-VEHICLE REPAIR >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
CONTROL DEVICE
Exploded ViewINFOID:0000000003849088
Removal and InstallationINFOID:0000000003849089
REMOVAL
1. Disconnect the battery cable from the negative terminal.
1. Selector lever knob 2. Lock pin 3. Knob cover
4. Control device assembly 5. Shift lock unit 6. Dust cover
Refer to GI-4, "
Components" for symbols in the figure.
JPDIA0741GB

TM-156
< ON-VEHICLE REPAIR >[CVT: RE0F09B]
CONTROL DEVICE
2. Slide knob cover (1) below selector lever downward.
CAUTION:
Be careful not to damage knob cover.
3. Pull lock pin (2) out of selector lever knob (3).
4. Remove selector lever knob and knob cover.
5. Remove center console assembly. Refer to IP-22, "
Exploded
View".
6. Remove control cable (1) from control device assembly. Refer to
TM-157, "
Exploded View".
7. Remove control device assembly (2).
8. Remove control device connector (A) using a flat-bladed screw-
driver (B).
CAUTION:
Be careful not to damage control device connector.
9. Remove shift lock unit from control device assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
When installing control cable (1) to control device assembly (2),
check that control cable is fully pressed in with the ribbed (A) surface
facing upward.
Inspection and AdjustmentINFOID:0000000003849090
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing control device. Refer to TM-152, "Inspection and Adjustment".
INSPECTION AFTER INSTALLATION
Check the CVT positions after adjusting the CVT positions. Refer to TM-152, "Inspection and Adjustment".
JPDIA0606ZZ
: Bolt
JPDIA0615ZZ
JPDIA0616ZZ
JPDIA0609ZZ

CONTROL CABLE
TM-157
< ON-VEHICLE REPAIR >[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
CONTROL CABLE
Exploded ViewINFOID:0000000003849091
Removal and InstallationINFOID:0000000003849092
REMOVAL
CAUTION:
Check that parking brake is applied before removal/installation.
1. Disconnect control cable from control device assembly. Refer to TM-155, "
Exploded View".
2. Remove the air duct (inlet) and air cleaner case. Refer to EM-26, "
Exploded View".
3. Remove control cable (1) from manual lever (A).
4. Remove lock plate (2) from control cable.
5. Remove control cable from bracket 2 (3).
6. Remove exhaust front tube. Refer to EX-5, "
Exploded View".
7. Remove heat plate.
1. Bracket 1 2. Lock plate 3. Bracket 2
4. Transaxle assembly 5. Control cable 6. Control device assembly
Refer to GI-4, "
Components" for symbols in the figure.
JPDIA0749GB
: Nut
JPDIA0601ZZ

TM-164
< ON-VEHICLE REPAIR >[CVT: RE0F09B]
AIR BREATHER HOSE
AIR BREATHER HOSE
Exploded ViewINFOID:0000000003849103
Removal and InstallationINFOID:0000000003849104
REMOVAL
1. Remove air duct (inlet) and air cleaner case. Refer to EM-26, "Exploded View".
2. Remove air breather hose from transaxle assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Check that air breather hose is not collapsed or blocked due to folding or bending when installed.
 Install air breather hose to air breather tube so that the paint mark
(A) faces upward. Also insert hose to the bend of air breather tube.
1. Air cleaner case 2. Air breather hose 3. Transaxle assembly
4. Heater pipe
: Vehicle front
JPDIA0592ZZ
SCIA7584J

TM-170
< REMOVAL AND INSTALLATION >[CVT: RE0F09B]
TRANSAXLE ASSEMBLY
 When using the drive plate location guide (commercial service tool:
31197CA000) (A), set it to the stud bolts which is used to install it
to the torque converter.
 When not using drive plate location guide, rotate torque converter
so that the stud bolt (B) for mounting the drive plate location guide
of torque converter aligns with the mounting position of service
hole.
 Rotate crankshaft so that the hole (A) for inserting drive plate loca-
tion guide of drive plate aligns with the service hole (B).
NOTE:
When not using drive plate location guide, insert stud bolt of torque
converter into the hole (C) of drive plate, aligning the drive plate
hole position and torque converter.
CAUTION:
Be careful not to strike the drive plate when installing the
torque converter stud bolt.
 Align the position of tightening nuts ( ) for drive plate with those
of the torque converter, and temporarily tighten the nuts. Then,
tighten the bolts to the specified torque.
CAUTION:
 When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
 When tightening the nuts for the torque converter after fixing
the crankshaft pulley bolts, confirm the tightening torque of
the crankshaft pulley mounting bolts. Refer to EM-79,
"Exploded View".
 Rotate crankshaft several turns and check that transaxle rotates freely without binding after con-
verter is installed to drive plate.
 Never reuse O-ring.
 Apply petroleum jelly to O-ring.
InspectionINFOID:0000000003849110
INSPECTION BEFORE INSTALLATION
After inserting a torque converter to transaxle assembly, check that
distance (A) is within the reference value limit.
INSPECTION AFTER INSTALLATION
Check the following items.
JPDIA0607ZZ
JPDIA0603ZZ
: 51 N·m (5.2 kg-m,38 ft-lb)
SCIA1861E
B: Scale
C : Straightedge
Distance A : Refer to TM-175, "Torque Converter".
JPDIA0620ZZ