NISSAN TEANA 2008 Service Manual
TEANA 2008
NISSAN
NISSAN
https://www.carmanualsonline.info/img/5/57391/w960_57391-0.png
NISSAN TEANA 2008 Service Manual
Page 4091 of 5121
![NISSAN TEANA 2008 Service Manual SEC-82
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
DescriptionINFOID:0000000003815014
BCM receives the engine NISSAN TEANA 2008 Service Manual SEC-82
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
DescriptionINFOID:0000000003815014
BCM receives the engine](/img/5/57391/w960_57391-4090.png)
SEC-82
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
B26E1 NO RECEPTION OF ENGINE STATUS SIGNAL
DescriptionINFOID:0000000003815014
BCM receives the engine status signal from ECM via CAN communication.
DTC LogicINFOID:0000000003815015
DTC DETECTION LOGIC
NOTE:
If DTC B26E1 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
SEC-28, "
BCM : DTC Logic".
If DTC B26E1 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
SEC-30, "
BCM : DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON under the following conditions.
- Selector lever is in the P or N position.
- Do not depress brake pedal.
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Go to SEC-82, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000003815016
1.INSPECTION START
1. Turn ignition switch ON.
2. Check “Self diagnostic result” with CONSULT-III.
3. Touch “ERASE”.
4.Perform DTC Confirmation Procedure.
See SEC-82, "
DTC Logic".
Is the DTC B26E1 displayed again?
YES >> GO TO 2.
NO >> GO TO 3.
2.REPLACE ECM
Replace ECM. Refer to EC-14, "
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description".
>> INSPECTION END
3.CHECK INTERMITTENT INCIDENT
Refer to GI-35, "
Intermittent Incident".
>> INSPECTION END
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
B26E1 NO RECEPTION OF ENGINE STATUS SIGNALBCM does not receive the engine status signal
from ECM when ignition switch is in the ON po-
sitionECM
Page 4130 of 5121
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
SEC-121
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
Wiring Diagram - INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION -
INFOID:0000000003845527
JCKWM1204GB
Page 4131 of 5121
SEC-122
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
JCKWM1205GB
Page 4132 of 5121
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
SEC-123
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
JCKWM1206GB
Page 4133 of 5121
SEC-124
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
JCKWM1207GB
Page 4134 of 5121
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
SEC-125
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
JCKWM1208GB
Page 4135 of 5121
SEC-126
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
JCKWM1209GB
Page 4136 of 5121
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
SEC-127
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
JCKWM1210GB
Page 4137 of 5121
SEC-128
< COMPONENT DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION
JCKWM1211GB
Page 4155 of 5121
![NISSAN TEANA 2008 Service Manual SEC-146
< ECU DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
BCM (BODY CONTROL MODULE)
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off
NISSAN TEANA 2008 Service Manual SEC-146
< ECU DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
BCM (BODY CONTROL MODULE)
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off](/img/5/57391/w960_57391-4154.png)
SEC-146
< ECU DIAGNOSIS >[INTELLIGENT KEY SYSTEM]
BCM (BODY CONTROL MODULE)
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off
REQ SW -RRNOTE:
The item is indicated, but not monitored. Off
REQ SW -BD/TRTrunk lid opener request switch is not pressed Off
Trunk lid opener request switch is pressed On
PUSH SWPush-button ignition switch (push switch) is not pressed Off
Push-button ignition switch (push switch) is pressed On
IGN RLY2 -F/BIgnition switch in OFF or ACC position Off
Ignition switch in ON position On
CLUCH SWNOTE:
The item is indicated, but not monitored. Off
BRAKE SW 1The brake pedal is not depressed On
The brake pedal is depressed Off
DETE/CANCL SWSelector lever in P position Off
Selector lever in any position other than P On
SFT PN/N SWSelector lever in any position other than P and N Off
Selector lever in P or N position On
S/L -LOCKSteering is locked Off
Steering is unlocked On
S/L -UNLOCKSteering is unlocked Off
Steering is locked On
S/L RELAY-F/BIgnition switch in OFF or ACC position Off
Ignition switch in ON position On
UNLK SEN -DRDriver door is unlocked Off
Driver door is locked On
PUSH SW -IPDMPush-button ignition switch (push-switch) is not pressed Off
Push-button ignition switch (push-switch) is pressed On
IGN RLY1 -F/BIgnition switch in OFF or ACC position Off
Ignition switch in ON position On
DETE SW -IPDMSelector lever in P position Off
Selector lever in any position other than P On
SFT PN -IPDMSelector lever in any position other than P and N Off
Selector lever in P or N position On
SFT P -METSelector lever in any position other than P Off
Selector lever in P position On
SFT N -METSelector lever in any position other than N Off
Selector lever in N position On
ENGINE STATEEngine stopped Stop
While the engine stalls Stall
At engine cranking Crank
Engine running Run
S/L LOCK-IPDMSteering is locked Off
Steering is unlocked On Monitor Item Condition Value/Status