warning NISSAN TEANA 2014 Service Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2014, Model line: TEANA, Model: NISSAN TEANA 2014Pages: 4801, PDF Size: 51.2 MB
Page 452 of 4801
![NISSAN TEANA 2014 Service Manual
DAS
ITS CONTROL UNITDAS-19
< ECU DIAGNOSIS INFORMATION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
Fail-safeINFOID:0000000009464654
If a malfunction occurs in each system, ITS contro l unit](/img/5/57390/w960_57390-451.png "NISSAN TEANA 2014 Service Manual
DAS
ITS CONTROL UNITDAS-19
< ECU DIAGNOSIS INFORMATION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
Fail-safeINFOID:0000000009464654
If a malfunction occurs in each system, ITS contro l unit")
DAS
ITS CONTROL UNITDAS-19
< ECU DIAGNOSIS INFORMATION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
Fail-safeINFOID:0000000009464654
If a malfunction occurs in each system, ITS contro l unit cancels each control, sounds a beep, and turns ON
the warning lamp or indicator lamp.
DTC Inspection Priority ChartINFOID:0000000009464655
If multiple DTCs are detected simultaneously, che ck them one by one depending on the following DTC inspec-
tion priority chart.
52
(W) Ground RR CAM ON Output Ignition switch ON 6 V
66
(B) Ground RR CAM COMP + Input Ignition switch ON
68
(G) Ground RR CAM CONT Input Ignition switch ON 5 V
69
(B) Ground RR CAM COMP + Input Ignition switch ON
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
+ − Signal name Input/
Output
ALOIA0179ZZ
ALOIA0179ZZ
System Buzzer Warning Indicator lamp Description
Lane Departure Warning (LDW) Low-pitched
tone Lane Departure Warning lamp Cancel
Blind Spot Warning (BSW) High-pitched
tone Blind Spot Warning lamp Cancel
Moving Object Detection (MOD) Low-pitched
tone Warning lamp MOD icon
(on camera screen) Cancel
Priority Detected items (DTC)
1 • U1000: CAN COMM CIRCUIT
• U1010: CONTROL UNIT (CAN)
2 • U1305: CAMERA IMAGE CALIB
• U1308: CAMERA CONFIG
3 • C1A39: STRG SEN CIR
• U0428: STRG SEN CAN CIR 2
• U111A: REAR CAMERA IMAGE SIGNAL
• U1232: ST ANGLE SEN CALIB
• U1309: PUMP UNIT CURRENT
• U130B: REAR CAMERA COMM ERROR
• U1310: PUMP UNIT CIRCUIT
4 • C1A03: VHCL SPEED SE CIRC
• C1A04: VDC FAIL
• U0122: VDC P-RUN DIAG
• U0416: VDC CHECKSUM DIAG
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 453 of 4801
![NISSAN TEANA 2014 Service Manual
DAS-20
< ECU DIAGNOSIS INFORMATION >[ITS CONTROL UNIT]
ITS CONTROL UNIT
DTC Index
INFOID:0000000009464656
NOTE:
• The details of time display are as follows:
- CRNT: A malfunction is detected now](/img/5/57390/w960_57390-452.png "NISSAN TEANA 2014 Service Manual
DAS-20
< ECU DIAGNOSIS INFORMATION >[ITS CONTROL UNIT]
ITS CONTROL UNIT
DTC Index
INFOID:0000000009464656
NOTE:
• The details of time display are as follows:
- CRNT: A malfunction is detected now")
DAS-20
< ECU DIAGNOSIS INFORMATION >[ITS CONTROL UNIT]
ITS CONTROL UNIT
DTC Index
INFOID:0000000009464656
NOTE:
• The details of time display are as follows:
- CRNT: A malfunction is detected now
- PAST: A malfunction was detected in the past
• IGN counter is displayed on FFD (Freeze Frame Data).
- 0: The malfunctions that are detected now
CAN communication system (U1000, U1010)
- 1 - 39: It increases like 0 → 1 → 2 ··· 38 → 39 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunction is detected again in the process.
- If it is over 39, it is fixed to 39 until the self-diagnosis results are erased. Other than CAN communication sy stem (Other than U1000, U1010)
- 1 - 49: It increases like 0 → 1 → 2 ··· 38 → 49 after returning to the normal condition whenever the ignition
switch OFF → ON. It returns to 0 when a malfunction is detected again in the process.
- If it is over 49, it is fixed to 49 until the self-diagnosis results are erased.
NOTE:
With the detection of “U1000” some systems do not perform the fail-safe operation.
Systems for fail-safe
• A: Lane Departure Warning (LDW)
• B: Blind Spot Warning (BSW)
• C: Moving Object Detection (MOD)
DTC
CONSULT display Warning lamp Fail-safe
Reference
CONSULT
Lane Departure Warning
Blind Spot Warning
Moving Object Detection
System
C1A03 VHCL SPEED SE CIRC ON ON ON A, B, C DAS-42
C1A04 VDC FAIL ON ON ON A, B, CDAS-43
C1A39 STRG SEN CIR ON ON ON A, B, CDAS-44
NO DTC IS
DETECTED. FURTHER
TESTING
MAY BE RE- QUIRED NO DTC IS DETECTED.
FURTHER TESTING MAY BE REQUIRED ——— — —
U0122 VDC P-RUN DIAG ON ON ON A, B, C DAS-45
U0416 VDC CHECKSUM DIAG ON ON ON A, B, CDAS-46
U0428 STRG SEN CAN CIR 2 ON ON ON A, B, CDAS-47
U1000NOTECAN COMM CIRCUIT ON ON ON A, B, CDAS-48
U1010 CONTROL UNIT (CAN) ON ON ON A, B, C DAS-49
U 111 AREAR CAMERA IMAGE
SIGNAL ON ON ON A, B, C
DAS-50
U1232 ST ANGLE SEN CALIB ON ON ON A, B, C DAS-52
U1305 CAMERA IMAGE CALIB ON ON ON A, B, CDAS-53
U1308 CAMERA CONFIG ON ON ON A, B, CDAS-54
U1309 PUMP UNIT CURRENT ON ON ON A, B, CDAS-55
U130BREAR CAMERA COMM
ERROR ON ON ON A, B, C
DAS-58
U1310 PUMP UNIT CIRCUIT ON ON ON A, B, C DAS-59
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 465 of 4801
![NISSAN TEANA 2014 Service Manual
DAS-32
< BASIC INSPECTION >[ITS CONTROL UNIT]
DIAGNOSIS AND REPAIR WORK FLOW
>> GO TO 2.
2.SELF-DIAGNOSIS WITH CONSULT
1. Perform “All DTC Reading” with CONSULT.
2. Check if the DTC is detected](/img/5/57390/w960_57390-464.png "NISSAN TEANA 2014 Service Manual
DAS-32
< BASIC INSPECTION >[ITS CONTROL UNIT]
DIAGNOSIS AND REPAIR WORK FLOW
>> GO TO 2.
2.SELF-DIAGNOSIS WITH CONSULT
1. Perform “All DTC Reading” with CONSULT.
2. Check if the DTC is detected")
DAS-32
< BASIC INSPECTION >[ITS CONTROL UNIT]
DIAGNOSIS AND REPAIR WORK FLOW
>> GO TO 2.
2.SELF-DIAGNOSIS WITH CONSULT
1. Perform “All DTC Reading” with CONSULT.
2. Check if the DTC is detected on the self-diagnosis results of “AVM”.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 3.
3.PRE-INSPECTION FOR DIAGNOSIS
Perform pre-inspection for diagnosis. Refer to DAS-34, "Inspection Procedure"
.
>> GO TO 4.
4.ACTION TEST
Perform LDW system action test to check the operation status. Refer to DAS-35, "Description"
.
>> GO TO 6.
5.TROUBLE DIAGNOSIS BY DTC
Perform trouble diagnosis for the detected DTC. Specify a malfunctioning part. Refer to DAS-20, "DTC Index"
(ITS CONTROL UNIT).
>> GO TO 7.
6.SYMPTOM DIAGNOSIS
Perform symptom diagnosis. Specify malfunctioning part. Refer to DAS-137, "Symptom Table"
.
>> GO TO 7.
7.MALFUNCTION PART REPAIR
Repair or replace the identified malfunctioning parts.
>> GO TO 8.
8.REPAIR CHECK (SELF-DIAGNOSIS WITH CONSULT)
Perform self-diagnosis with CONSULT. Check that any DTC is not detected. Erase DTC if DTC is detected
before the repair. Check that DTC is not detected again.
Is any DTC detected?
YES >> GO TO 5.
NO >> GO TO 9.
9.REPAIR CHECK (ACTION TEST)
Perform LDW system action test. Also check the system operation.
Does it operate normally?
YES >> Inspection End.
NO >> GO TO 4.
Diagnostic Work SheetINFOID:0000000009464659
DESCRIPTION
In general, each customer feels differently about an inci dent. It is important to fully understand the symptoms
or conditions for a customer complaint.
There are many operating conditions that lead to the malfunction. A good grasp of such conditions can make
troubleshooting faster and more accurate.
Some conditions may cause the lane departure warning lamp to stay ON.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 468 of 4801
![NISSAN TEANA 2014 Service Manual
DAS
ACTION TESTDAS-35
< BASIC INSPECTION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
ACTION TEST
DescriptionINFOID:0000000009464661
• Perform action test to verify the customers concern.](/img/5/57390/w960_57390-467.png "NISSAN TEANA 2014 Service Manual
DAS
ACTION TESTDAS-35
< BASIC INSPECTION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
ACTION TEST
DescriptionINFOID:0000000009464661
• Perform action test to verify the customers concern.")
DAS
ACTION TESTDAS-35
< BASIC INSPECTION > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
ACTION TEST
DescriptionINFOID:0000000009464661
• Perform action test to verify the customer's concern.
• Perform action test and check the system operation after system diagnosis.
WARNING:
Be careful of traffic conditions and safety aro und the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-82, "Precautions for Lane Departure Warning"
.
Inspection ProcedureINFOID:0000000009464662
WARNING:
Be careful of traffic conditions and safety aro und the vehicle when performing road test.
CAUTION:
• Fully understand the following it ems well before the road test;
- Precautions: Refer to DAS-73, "Precaution for LDW System Service"
.
- System description for LDW: Refer to DAS-77, "System Description"
.
- System description for BSW: Refer to DAS-152, "System Description"
.
- System description for MOD: Refer to DAS-228, "System Description"
.
- Handling precaution: Refer to DAS-232, "Precautions for Moving Objects Detection"
.
1.CHECK LDW SYSTEM SETTING
1. Start the engine.
2. Check that the LDW system setting can be enabl ed/disabled on the vehicle information display.
3. Turn OFF the ignition switch and wait for 30 seconds or more.
4. Check that the previous setting is saved when the engine starts again.
>> GO TO 2.
2.ACTION TEST FOR LDW
1. Enable the setting of the LDW system on the vehicle information display.
2. Turn warning systems switch ON (w arning systems ON indicator is ON).
3. Check the LDW operation according to the following table.
Vehicle condition/ Driver's operation Action Warning sys-
tems ON indi-
cator Indication on the combination
meter Buzzer
Less than
Approx. 60 km/h (40 MPH) Close to lane marker No action ON —
ALOIA0191GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 469 of 4801
![NISSAN TEANA 2014 Service Manual
DAS-36
< BASIC INSPECTION >[ITS CONTROL UNIT]
ACTION TEST
NOTE:
After the operating conditions of warning are satisf ied, the warning continues until the vehicle speed
reaches approximately 60 km/h](/img/5/57390/w960_57390-468.png "NISSAN TEANA 2014 Service Manual
DAS-36
< BASIC INSPECTION >[ITS CONTROL UNIT]
ACTION TEST
NOTE:
After the operating conditions of warning are satisf ied, the warning continues until the vehicle speed
reaches approximately 60 km/h")
DAS-36
< BASIC INSPECTION >[ITS CONTROL UNIT]
ACTION TEST
NOTE:
After the operating conditions of warning are satisf ied, the warning continues until the vehicle speed
reaches approximately 60 km/h (40 MPH). Refer to DAS-77, "System Description"
.
>> Inspection End.
Approx. 70 km/h (45 MPH) or more Close to lane marker
Warning
• Buzzer sounds
• Warning lamp
blinks ON
Short contin-
uous beeps
• Close to lane marker
• Turn signal ON (Deviate side) No action ON —
Vehicle condition/ Driver's operation Action
Warning sys-
tems ON indi-
cator Indication on the combination
meter BuzzerALOIA0190GB
ALOIA0191GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 496 of 4801
![NISSAN TEANA 2014 Service Manual
DAS
WARNING SYSTEMS SWITCH CIRCUITDAS-63
< DTC/CIRCUIT DIAGNOSIS > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
WARNING SYSTEMS SWITCH CIRCUIT
Component Function CheckINFOID:0000000009464702
1.](/img/5/57390/w960_57390-495.png "NISSAN TEANA 2014 Service Manual
DAS
WARNING SYSTEMS SWITCH CIRCUITDAS-63
< DTC/CIRCUIT DIAGNOSIS > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
WARNING SYSTEMS SWITCH CIRCUIT
Component Function CheckINFOID:0000000009464702
1.")
DAS
WARNING SYSTEMS SWITCH CIRCUITDAS-63
< DTC/CIRCUIT DIAGNOSIS > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
WARNING SYSTEMS SWITCH CIRCUIT
Component Function CheckINFOID:0000000009464702
1.CHECK WARNING SYSTEMS SWITCH INPUT SIGNAL
1. Turn the ignition switch ON.
2. Select the DATA MONITOR item “I TS SW 1” of “AVM” with CONSULT.
3. With operating the warning systems switch, check the monitor status.
Is the inspection result normal?
YES >> Warning systems switch circuit is normal.
NO >> Refer to DAS-63, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009464703
Regarding Wiring Diagram information, refer to DAS-22, "Wiring Diagram".
1.CHECK WARNING SYSTEMS SWITCH SIGNAL INPUT
1. Turn the ignition switch ON.
2. Check voltage between ITS control unit harness connector and ground.
Is the inspection result normal?
YES >> Replace the ITS control unit. Refer to DAS-68, "Removal and Installation".
NO >> GO TO 2.
2.CHECK WARNING SYSTEMS SWITCH
1. Turn ignition switch OFF.
2. Remove warning systems switch.
3. Check warning systems switch. Refer to DAS-64, "Component Inspection"
.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Replace the warning systems switch. Refer to DAS-142, "Removal and Installation"
.
3.CHECK WARNING SYSTEMS SWITCH GROUND CIRCUIT
Check continuity between warning system switch harness connector terminal and ground.
Is the inspection result normal?
YES >> GO TO 4.
Monitor item Condition Monitor status
ITS SW 1 Warning systems switch is pressed On
Warning systems switch is not pressed OFF
Te r m i n a l s Condition
Vo l ta g e
(Approx.)
(+) (
−)
ITS control unit
GroundWarning
systems switch
Connector Terminal
M58 32 Pressed 0 V
Released 12 V
Warning system switch
GroundContinuity
Connector Terminal
M62 8 Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 497 of 4801
![NISSAN TEANA 2014 Service Manual
DAS-64
< DTC/CIRCUIT DIAGNOSIS >[ITS CONTROL UNIT]
WARNING SYSTEMS SWITCH CIRCUIT
NO >> Repair harness or connector.
4.CHECK WARNING SYSTEMS SWITCH
SIGNAL INPUT CIRCUIT FOR OPEN
1. Disconnect the IT](/img/5/57390/w960_57390-496.png "NISSAN TEANA 2014 Service Manual
DAS-64
< DTC/CIRCUIT DIAGNOSIS >[ITS CONTROL UNIT]
WARNING SYSTEMS SWITCH CIRCUIT
NO >> Repair harness or connector.
4.CHECK WARNING SYSTEMS SWITCH
SIGNAL INPUT CIRCUIT FOR OPEN
1. Disconnect the IT")
DAS-64
< DTC/CIRCUIT DIAGNOSIS >[ITS CONTROL UNIT]
WARNING SYSTEMS SWITCH CIRCUIT
NO >> Repair harness or connector.
4.CHECK WARNING SYSTEMS SWITCH
SIGNAL INPUT CIRCUIT FOR OPEN
1. Disconnect the ITS control unit connector.
2. Check continuity between the ITS control unit har ness connector and warning system switch harness con-
nector.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair the harnesses or connectors.
5.CHECK WARNING SYSTEMS SWITCH SI GNAL INPUT CIRCUIT FOR SHORT
Check continuity between the ITS c ontrol unit harness connector and ground.
Is the inspection result normal?
YES >> Replace the ITS control unit. Refer to DAS-68, "Removal and Installation".
NO >> Repair the harnesses or connectors.
Component InspectionINFOID:0000000009464704
1.CHECK WARNING SYSTEMS SWITCH
Check continuity of warning systems switch.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace the warning systems switch. Refer to DAS-142, "Removal and Installation"
.
ITS control unit Warning system switch
Continuity
Connector Terminal Connector Terminal
M58 32 M62 6 Yes
ITS control unit GroundContinuity
Connector Terminal
M58 32 No
Terminal Condition Continuity
68 When warning systems switch is pressed Yes
When warning systems switch is released No
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 498 of 4801
![NISSAN TEANA 2014 Service Manual
DAS
WARNING SYSTEMS ON INDICATOR CIRCUITDAS-65
< DTC/CIRCUIT DIAGNOSIS > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
WARNING SYSTEMS ON INDICATOR CIRCUIT
Component Function CheckINFOID:0000000](/img/5/57390/w960_57390-497.png "NISSAN TEANA 2014 Service Manual
DAS
WARNING SYSTEMS ON INDICATOR CIRCUITDAS-65
< DTC/CIRCUIT DIAGNOSIS > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
WARNING SYSTEMS ON INDICATOR CIRCUIT
Component Function CheckINFOID:0000000")
DAS
WARNING SYSTEMS ON INDICATOR CIRCUITDAS-65
< DTC/CIRCUIT DIAGNOSIS > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
WARNING SYSTEMS ON INDICATOR CIRCUIT
Component Function CheckINFOID:0000000009464705
1.CHECK WARNING SYST EMS ON INDICATOR
1. Turn the ignition switch ON.
2. Select the active test item “BSW ON INDICATOR” of “AVM” with CONSULT.
3. With operating the test item, check the operation.
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to DAS-65, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009464706
Regarding Wiring Diagram information, refer to DAS-22, "Wiring Diagram".
1.CHECK WARNING ON INDICATOR POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect warning system switch connector.
3. Turn ignition switch ON.
4. Check voltage between warning system switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair the warning systems ON indicator power supply circuit.
2.CHECK WARNING SYSTEMS ON INDICATOR SIGNAL FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect the ITS control unit harness connector.
3. Check continuity between the ITS control unit har ness connector and warning system switch harness con-
nector.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair the harnesses or connectors.
3.CHECK WARNING SYSTEMS ON INDI CATOR SIGNAL CIRCUIT FOR SHORT
Check continuity between the ITS control unit harness connector and ground.
On : Warning systems ON indicator illuminates
Off : Warning systems ON in dicator is turned OFF
Te r m i n a l s
Vo l ta g e
(Approx.)
(+) (
−)
Warning system switch Ground
Connector Terminal
M62 5 Battery voltage
ITS control unit Warning system switch Continuity
Connector Terminal Connector Terminal
M5833M62 3 Yes
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 499 of 4801
![NISSAN TEANA 2014 Service Manual
DAS-66
< DTC/CIRCUIT DIAGNOSIS >[ITS CONTROL UNIT]
WARNING SYSTEMS ON
INDICATOR CIRCUIT
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair the harnesses or connectors.
4.CHECK WARNING SY](/img/5/57390/w960_57390-498.png "NISSAN TEANA 2014 Service Manual
DAS-66
< DTC/CIRCUIT DIAGNOSIS >[ITS CONTROL UNIT]
WARNING SYSTEMS ON
INDICATOR CIRCUIT
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair the harnesses or connectors.
4.CHECK WARNING SY")
DAS-66
< DTC/CIRCUIT DIAGNOSIS >[ITS CONTROL UNIT]
WARNING SYSTEMS ON
INDICATOR CIRCUIT
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair the harnesses or connectors.
4.CHECK WARNING SYSTEMS ON INDICATOR
Check the warning systems ON indicator. Refer to DAS-66, "Component Inspection"
.
Is the inspection result normal?
YES >> Replace the ITS control unit. Refer to DAS-68, "Removal and Installation".
NO >> Replace warning systems switch. DAS-142, "Removal and Installation"
.
Component InspectionINFOID:0000000009464707
1.CHECK WARNING SYSTEMS ON INDICATOR
Apply battery voltage to warning systems switch termi nals 3 and 5, and then check if the warning systems ON
indicator illuminates.
Is the inspection result normal?
YES >> Inspection End.
NO >> Replace the warning systems switch. Refer to DAS-142, "Removal and Installation"
.
ITS control unit
GroundContinuity
Connector Terminal
M58 33 No
Te r m i n a l s Condition Warning sys-
tems ON indica-
tor
(+) (-)
53 When the battery voltage is applied On
When the battery voltage is not applied Off
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 500 of 4801
![NISSAN TEANA 2014 Service Manual
DAS
WARNING BUZZER CIRCUITDAS-67
< DTC/CIRCUIT DIAGNOSIS > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
WARNING BUZZER CIRCUIT
Component Function CheckINFOID:0000000009464708
1.CHECK WARNING BU](/img/5/57390/w960_57390-499.png "NISSAN TEANA 2014 Service Manual
DAS
WARNING BUZZER CIRCUITDAS-67
< DTC/CIRCUIT DIAGNOSIS > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
WARNING BUZZER CIRCUIT
Component Function CheckINFOID:0000000009464708
1.CHECK WARNING BU")
DAS
WARNING BUZZER CIRCUITDAS-67
< DTC/CIRCUIT DIAGNOSIS > [ITS CONTROL UNIT]
C
D E
F
G H
I
J
K L
M B
N P
A
WARNING BUZZER CIRCUIT
Component Function CheckINFOID:0000000009464708
1.CHECK WARNING BUZZER
1. Turn the ignition switch ON.
2. Select the active test item “BUZZER” of “BCM” with CONSULT.
3. With operating the test item, check the operation.
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to DAS-67, "Diagnosis Procedure"
.
Diagnosis ProcedureINFOID:0000000009464709
1.CHECK WARNING BUZZER OPERATION
While activating the buzzer with CONSULT, listen for the buzzer sound.
Does warning buzzer sound?
YES >> Replace the ITS control unit. Refer to DAS-68, "Removal and Installation".
NO >> Replace the combination meter (buzzer). On : Warning buzzer is activated.
Off : Warning buzzer is not activated.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM