DISPLAY UNIT NISSAN TEANA 2014 Service Manual

EC-606
< SYSTEM DESCRIPTION >[VQ35DE]
DIAGNOSIS SYSTEM (ECM)
COOLING FANHI/MID/
LOW/OFF • The control condition of the cool-
ing fan (determined by ECM ac-
cording to the input signals) is
indicated.
HI: High speed operation
MID: Middle speed operation
LOW: Low speed operation
OFF: Stop
HO2S2 HTR (B1)
On/Off Indicates [On/Off] condition of heat-
ed oxygen sensor 2 heater deter-
mined by ECM according to the
input signals.
HO2S2 HTR (B2)
ALT DUTY SIG On/Off The control condition of the power
generation voltage variable control
(determined by ECM according to
the input signals) is indicated.
• On: Power generation voltage variable control is active.
• Off: Power generation voltage
variable control is inactive.
I/P PULLY SPD rpm Indicates the engine speed comput-
ed from the input speed sensor sig-
nal.
VEHICLE SPEED km/h or
mph The vehicle speed computed from
the vehicle speed signal sent from
TCM is displayed.
IDL A/V LEARN YET/
CMPLT Displays the condition of idle air vol-
ume learning
• Yet: Idle Air Volume Learning has not been performed yet.
• Cmplt: Idle Air Volume Learning
has already been performed suc-
cessfully.
TRVL AFTER MIL km or
mile Distance traveled while MIL is acti-
vated.
ENG OIL TEMP °C or °F The engine oil temperature (deter-
mined by the signal voltage of the
engine oil temperature sensor) is
displayed.
VHCL SPEED SE km/h or
mph The vehicle speed computed from
the vehicle speed signal sent from
combination meter is displayed.
SET VHCL SPD km/h or
mph • The preset vehicle speed is dis-
played.
MAIN SW On/Off Indicates [On/Off] condition from
MAIN switch signal.
CANCEL SW On/Off Indicates [On/Off] condition from
CANCEL switch signal.
RESUME/ACC SW On/Off Indicates [On/Off] condition from
RESUME/ACCELERATE switch sig-
nal.
SET SW On/Off Indicates [On/Off] condition from
SET/COAST switch signal.
Monitored item Unit
Monitor Item Selec-
tion
Description Remarks
ECU IN-
PUT SIG- NALS MAIN-
SIG-
NALS
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DIAGNOSIS SYSTEM (ECM)EC-607
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
BRAKE SW1 On/Off
Indicates [On/Off] condition from
brake pedal position switch signal or
ASCD clutch switch.
BRAKE SW2 On/Off Indicates [On/Off] condition of stop
lamp switch signal.
VHCL SPD CUT Non/
Cut • Indicates the vehicle cruise condi-
tion.
NON: Vehicle speed is maintained
at the ASCD set speed.
CUT: Vehicle speed decreased to
excessively low compared with
the ASCD set speed, and ASCD
operation is cut off.
LO SPEED CUT Non/
Cut • Indicates the vehicle cruise condi-
tion.
NON: Vehicle speed is maintained
at the ASCD set speed.
CUT: Vehicle speed decreased to
excessively low, and ASCD oper-
ation is cut off.
AT OD MONITOR On/Off • Indicates [On/Off] condition of
CVT O/D according to the input
signal from the TCM.
AT OD CANCEL On/Off • Indicates [On/Off] condition of
CVT O/D cancel request signal.
CRUISE LAMP On/Off Indicates [On/Off] condition of
CRUISE lamp dete rmined by the
ECM according to the input signals.
SET LAMP On/Off • Indicates [On/Off] condition of
SET lamp determined by the ECM
according to the input signals.
ALT DUTY % Indicates the duty ratio of the power
generation command value. The ra-
tio is calculated by ECM based on
the battery current sensor signal.
BAT CUR SEN mV The signal voltage of battery current
sensor is displayed.
A/F ADJ-B1
— Indicates the correction of a factor
stored in ECM. The factor is calcu-
lated from the difference between
the target air-fuel ratio stored in ECM
and the air-fuel ratio calculated from
A/F sensor 1 signal.
A/F ADJ-B2
P/N POSI SW On/Off ××Indicates [On/Off] condition from the
park/neutral position (PNP) signal.
INT/A TEMP SE °C or °F ×× The intake air temperature (deter-
mined by the signal voltage of the in-
take air temperature sensor) is
indicated.
AC PRESS SEN V The signal voltage from the refriger-
ant pressure sensor is displayed.
VTC DTY EX B2
*——
Monitored item Unit
Monitor Item Selec-
tion
Description Remarks
ECU IN-
PUT SIG- NALS MAIN-
SIG-
NALS
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-608
< SYSTEM DESCRIPTION >[VQ35DE]
DIAGNOSIS SYSTEM (ECM)
EVAP LEAK DIAGYe t / C m -
plt Indicates the condition of EVAP leak
diagnosis.
• YET: EVAP leak diagnosis has not been performed yet.
• CMPLT: EVAP leak diagnosis has
been performed successfully.
EVAP DIAG READY On/Off Indicates the ready condition of
EVAP leak diagnosis.
• On: Diagnosis has been ready
condition.
• Off: Diagnosis has not been ready condition.
BAT TEMP SEN V The signal voltage from the battery
temperature sensor is displayed.
THRTL STK CNT B1
*——
HO2 S2 DIAG1(B2) INCMP/
CMPLT Indicates DTC P0139 self-diagnosis
(delayed responce) condition.
• INCMP: Self-diagnosis is incom- plete.
• CMPLT: Self-diagnosis is com-
plete.
A/F SEN1 DIAG1(B2) INCMP/
CMPLT Indicates DTC P015C or P015D
self-diagnosis condition.
• INCMP: Self-diagnosis is incom-
plete.
• CMPLT: Self-diagnosis is com- plete.
A/F SEN1 DIAG1(B1) INCMP/
CMPLT Indicates DTC P015A or P015B self-
diagnosis condition.
• INCMP: Self-diagnosis is incom- plete.
• CMPLT: Self-diagnosis is com- plete.
A/F SEN1 DIAG2(B2) INCMP/
CMPLT Indicates DTC P014E or P014F self-
diagnosis condition.
• INCMP: Self-diagnosis is incom-
plete.
• CMPLT: Self-diagnosis is com- plete.
A/F SEN1 DIAG2(B1) INCMP/
CMPLT Indicates DTC P014C or P014D
self-diagnosis condition.
• INCMP: Self-diagnosis is incom- plete.
• CMPLT: Self-diagnosis is com- plete.
A/F SEN1 DIAG3(B2) ABSNT/
PRSNT Indicates DTC P014C, P014D,
P015A or P015B se lf-diagnosis con-
dition.
• ABSNT: The vehicle condition is not within the diagnosis range.
• PRSNT: The vehicle condition is within the diagnosis range.
Monitored item Unit
Monitor Item Selec-
tion
Description Remarks
ECU IN-
PUT SIG- NALS MAIN-
SIG-
NALS
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DIAGNOSIS SYSTEM (ECM)EC-609
< SYSTEM DESCRIPTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
*: The item is indicated, but not used.
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
WORK SUPPORT MODE
Work Item
A/F SEN1 DIAG3(B1)ABSNT/
PRSNT Indicates DTC P014C, P014D,
P015A or P015B self-diagnosis con-
dition.
• ABSNT: The vehicle condition is not within the diagnosis range.
• PRSNT: The vehicle condition is within the diagnosis range.
HO2 S2 DIAG2(B2) INCMP/
CMPLT Indicates DTC P0139 self-diagnosis
(slow responce ) condition.
• INCMP: Self-diagnosis is incom- plete.
• CMPLT: Self-diagnosis is com-
plete.
HO2 S2 DIAG2(B1) INCMP/
CMPLT Indicates DTC P0139 self-diagnosis
(slow responce ) condition.
• INCMP: Self-diagnosis is incom-
plete.
• CMPLT: Self-diagnosis is com- plete.
EOP SENSOR mV The signal voltage of EOP sensor is
displayed.
HO2 S2 DIAG1(B1) INCMP/
CMPLT Indicates DTC P0139 self-diagnosis
(delayed responce) condition.
• INCMP: Self-diagnosis is incom-
plete.
• CMPLT: Self-diagnosis is com- plete.
A/F-S ATMSPHRC
CRCT B1 — Displays a determined value of at-
mospheric correction factor neces-
sary for correcting an A/F sensor
signal input to ECM. The signal used
for the correction is an A/F sensor
signal transmitted while driving un-
der atmospheric pressure.
A/F-S ATMSPHRC
CRCT B2 — Displays a determined value of at-
mospheric correction factor neces-
sary for correcting an A/F sensor
signal input to ECM. The signal used
for the correction is an A/F sensor
signal transmitted while driving un-
der atmospheric pressure.
A/F-S ATMSPHRC
CRCT UP B1 count Displays the number of updates of
the A/F sensor atmospheric correc-
tion factor.
A/F-S ATMSPHRC
CRCT UP B2 count Displays the number of updates of
the A/F sensor atmospheric correc-
tion factor.
Monitored item Unit
Monitor Item Selec-
tion
Description Remarks
ECU IN-
PUT SIG- NALS MAIN-
SIG-
NALS
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-634
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
*1: 1st trip DTC No. is
the same as DTC No.
*2: This number is prescribed by SAE J2012/ISO 15031-6.
*3: In Diagnostic Test Mode II (Self-diagnostic results), this number is controlled by NISSAN.
*4: Refer to EC-695, "Description"
.
*5: The troubleshooting for this DTC needs CONSULT.
*6: When the ECM is in the mode displays SRT status, MIL may blink. For the details, refer to “How to Display SRT Status”.
*7: SRT code will not be set if the self-diagnostic result is NG.
*8: When the fail-safe operations for both self-diagnoses occur, the MIL illuminates.
Test Value and Test LimitINFOID:0000000009952493
The following is the information specified in Service $06 of SAE J1979/ISO 15031-5.
The test value is a parameter used to determine whether a system/circuit diagnostic test is OK or NG while
being monitored by the ECM during self-diagnosis. The test limit is a reference value which is specified as the
maximum or minimum value and is compared with the test value being monitored.
These data (test value and test limit) are specified by On Board Monitor ID (OBDMID), Test ID (TID), Unit and
Scaling ID and can be displayed on the GST screen.
The items of the test value and test limit will be di splayed with GST screen which items are provided by the
ECM. (e.g., if bank 2 is not applied on this v ehicle, only the items of bank 1 are displayed)
P2103 2103 ETC MOT PWR — 1 ×BEC-931
P2118 2118 ETC MOT-B1 — 1 ×BEC-936
P2119 2119 ETC ACTR-B1 — 1 ×BEC-938
P2122 2122 APP SEN 1/CIRC — 1 ×BEC-940
P2123 2123 APP SEN 1/CIRC — 1 ×BEC-940
P2127 2127 APP SEN 2/CIRC — 1 ×BEC-942
P2128 2128 APP SEN 2/CIRC — 1 ×BEC-942
P2135 2135 TP SENSOR-B1 — 1 ×BEC-945
P2138 2138 APP SENSOR — 1 ×BEC-947
DTC*1
Items
(CONSULT screen terms) SRT
code Trip MIL Permanent
DTC group*4Refer-
ence page
CONSULT
GST
*2ECM*3
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-635
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
Item
OBD-
MID Self-diagnostic test item DTC Test value and Test
limit
(GST display) Description
TID Unit and
Scaling ID
HO2S 01H Air fuel ratio (A/F) sensor 1
(Bank 1) P0131 83H 0BH
Minimum sensor output voltage for test
cycle
P0131 84H 0BH Maximum sensor output voltage for
test cycle
P0130 85H 0BH Minimum sensor output voltage for test
cycle
P0130 86H 0BH Maximum sensor output voltage for
test cycle
P0133 87H 04H Response rate: Response ratio (lean
to rich)
P0133 88H 04H Response rate: Response ratio (rich to
lean)
P2A00 or P2096 89H 84H The amount of shift in air fuel ratio (too
lean)
P2A00 or P2097 8AH 84H The amount of shift in air fuel ratio (too
rich)
P0130 8BH 0BH Difference in sensor output voltage
P0133 8CH 83H Response gain at the limited frequency
P014C 8DH 04H O2 sensor slow response - Rich to
lean bank 1 sensor 1
P014C 8EH 04H O2 sensor slow response - Rich to
lean bank 1 sensor 1
P014D 8FH 84H O2 sensor slow response - Lean to rich
bank 1 sensor 1
P014D 90H 84H O2 sensor slow response - Lean to rich
bank 1 sensor 1
P015A 91H 01H O2 sensor delayed response - Rich to
lean bank 1 sensor 1
P015A 92H 01H O2 sensor delayed response - Rich to
lean bank 1 sensor 1
P015B 93H 01H O2 sensor delayed response - Lean to
rich bank 1 sensor 1
P015B 94H 01H O2 sensor delayed response - Lean to
rich bank 1 sensor 1
P0133 95H 04H Response rate: Response ratio (lean
to rich)
P0133 96H 84H Response rate: Response ratio (rich to
lean)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-636
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
HO2S02H
Heated oxygen sensor 2
(Bank 1) P0138 07H 0CH
Minimum sensor output voltage for test
cycle
P0137 08H 0CH Maximum sensor output voltage for
test cycle
P0138 80H 0CH Sensor output voltage
P0139 81H 0CH Difference in sensor output voltage
P0139 82H 11H Rear O2 sensor delay response diag-
nosis
03H Heated oxygen sensor 3
(Bank 1) P0143 07H 0CH
Minimum sensor output voltage for test
cycle
P0144 08H 0CH Maximum sensor output voltage for
test cycle
P0146 80H 0CH Sensor output voltage
P0145 81H 0CH Difference in sensor output voltage
05H Air fuel ratio (A/F) sensor 1
(Bank 2) P0151 83H 0BH
Minimum sensor output voltage for test
cycle
P0151 84H 0BH Maximum sensor output voltage for
test cycle
P0150 85H 0BH Minimum sensor output voltage for test
cycle
P0150 86H 0BH Maximum sensor output voltage for
test cycle
P0153 87H 04H Response rate: Response ratio (lean
to rich)
P0153 88H 04H Response rate: Respon
se ratio (rich to
lean)
P2A03 or P2098 89H 84H The amount of shift in air fuel ratio (too
lean)
P2A03 or P2099 8AH 84H The amount of shift in air fuel ratio (too
rich)
P0150 8BH 0BH Difference in sensor output voltage
P0153 8CH 83H Response gain at the limited frequency
P014E 8DH 04H O2 sensor slow response - Rich to
lean bank 2 sensor 1
P014E 8EH 04H O2 sensor slow response - Rich to
lean bank 2 sensor 1
P014F 8FH 84H O2 sensor slow response - Lean to rich
bank 2 sensor 1
P014F 90H 84H O2 sensor slow response - Lean to rich
bank 2 sensor 1
P015C 91H 01H O2 sensor delayed response - Rich to
lean bank 2 sensor 1
P015C 92H 01H O2 sensor delayed response - Rich to
lean bank 2 sensor 1
P015D 93H 01H O2 sensor delayed response - Lean to
rich bank 2 sensor 1
Item
OBD-
MID Self-diagnostic test item DTC Test value and Test
limit
(GST display) Description
TID Unit and
Scaling ID
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-637
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
HO2S 05H
Air fuel ratio (A/F) sensor 1
(Bank 2) P015D 94H 01H
O2 sensor delayed response - Lean to
rich bank 2 sensor 1
P0153 95H 04H Response rate: Response ratio (lean
to rich)
P0153 96H 84H Response rate: Response ratio (rich to
lean)
06H Heated oxygen sensor 2
(Bank 2) P0158 07H 0CH
Minimum sensor output voltage for test
cycle
P0157 08H 0CH Maximum sensor output voltage for
test cycle
P0158 80H 0CH Sensor output voltage
P0159 81H 0CH Difference in sensor output voltage
P0159 82H 11H Rear O2 sensor delay response diag-
nosis
07H Heated oxygen sensor 3
(Bank2) P0163 07H 0CH
Minimum sensor output voltage for test
cycle
P0164 08H 0CH Maximum sensor output voltage for
test cycle
P0166 80H 0CH Sensor output voltage
P0165 81H 0CH Difference in sensor output voltage
CATA-
LY S T 21H
Three way catalyst function
(Bank1) P0420 80H 01H O2 storage index
P0420 82H 01H Switching time lag engine exhaust in-
dex value
P2423 83H 0CH Difference in 3rd O2 sensor output
voltage
P2423 84H 84H O2 storage index in HC trap catalyst
22H Three way catalyst function
(Bank2) P0430 80H 01H O2 storage index
P0430 82H 01H Switching time lag engine exhaust in-
dex value
P2424 83H 0CH Difference in 3rd O2 sensor output
voltage
P2424 84H 84H O2 storage index in HC trap catalyst
EGR
SYSTEM 31H EGR function P0400 80H 96H
Low flow faults: EGR temp change rate
(short term)
P0400 81H 96H Low flow faults: EGR temp change rate
(long term)
P0400 82H 96H Low flow faults: Difference between
max EGR temp and EGR temp under
idling condition
P0400 83H 96H Low flow faults: Max EGR temp
P1402 84H 96H High Flow Faults: EGR temp increase
rate
Item
OBD-
MID Self-diagnostic test item DTC Test value and Test
limit
(GST display) Description
TID Unit and
Scaling ID
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-638
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
VVT
SYSTEM 35H VVT Monitor (Bank1)
P0011 80H 9DH
VTC intake function diagnosis (VTC
alignment check diagnosis)
P0014 81H 9DH VTC exhaust function diagnosis (VTC
alignment check diagnosis)
P0011 82H 9DH VTC intake function diagnosis (VTC
drive failure diagnosis)
P0014 83H 9DH VTC exhaust function diagnosis (VTC
drive failure diagnosis)
P100A 84H 10H VEL slow response diagnosis P1090 85H 10H VEL servo system diagnosis
P0011 86H 9DH VTC intake intermediate lock function
diagnosis (VTC intermediate position
alignment check diagnosis)
Advanced: P052A Retarded: P052B 87H 9DHVTC intake intermediate lock system
diagnosis (VTC intermediate lock posi-
tion check diagnosis)
36H VVT Monitor (Bank2) P0021 80H 9DH
VTC intake function diagnosis (VTC
alignment check diagnosis)
P0024 81H 9DH VTC exhaust function diagnosis (VTC
alignment check diagnosis)
P0021 82H 9DH VTC intake function diagnosis (VTC
drive failure diagnosis)
P0024 83H 9DH VTC exhaust function diagnosis (VTC
drive failure diagnosis)
P100B 84H 10H VEL slow response diagnosis P1093 85H 10H VEL servo system diagnosis
P0021 86H 9DH VTC intake intermediate lock function
diagnosis (VTC intermediate position
alignment check diagnosis)
Advanced: P052C Retarded: P052D 87H 9DHVTC intake intermediate lock system
diagnosis (VTC intermediate lock posi-
tion check diagnosis)
EVAP
SYSTEM 39H
EVAP control system leak
(Cap Off) P0455 80H 0CHDifference in pressure sensor output
voltage before and after pull down
3BH EVAP control system leak
(Small leak) P0442 80H 05H
Leak area index (for more than 0.04
inch)
3CH EVAP control system leak
(Very small leak) P0456 80H 05H
Leak area index (for more than 0.02
inch)
P0456 81H FDH Maximum internal pressure of EVAP
system during monitoring
P0456 82H FDH Internal pressure of EVAP system at
the end of monitoring
3DH Purge flow system P0441 83H 0CH Difference in pressure sensor output
voltage before and after vent control
valve close
Item
OBD-
MID Self-diagnostic test item DTC Test value and Test
limit
(GST display) Description
TID Unit and
Scaling ID
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-639
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
O2 SEN-
SOR
HEATER 41H A/F sensor 1 heater (Bank 1)
Low Input: P0031
High Input: P0032 81H 0BHConverted value of heater electric cur-
rent to voltage
42H Heated oxygen sensor 2 heat-
er (Bank 1) Low Input: P0037
High Input: P0038 80H 0CH
Converted value of heater electric cur-
rent to voltage
43H Heated oxygen sensor 3 heat-
er (Bank 1) P0043 80H 0CHConverted value of heater electric cur-
rent to voltage
45H A/F sensor 1 heater (Bank 2) Low Input: P0051
High Input: P0052 81H 0BHConverted value of heater electric cur-
rent to voltage
46H Heated oxygen sensor 2 heat-
er (Bank 2) Low Input: P0057
High Input: P0058 80H 0CH
Converted value of heater electric cur-
rent to voltage
47H Heated oxygen sensor 3 heat-
er (Bank 2) P0063 80H 0CHConverted value of heater electric cur-
rent to voltage
SEC-
OND-
ARY AIR 71H Secondary air system P0411 80H 01H
Secondary air injection system incor-
rect flow detected
Bank1: P0491
Bank2: P0492 81H 01H
Secondary air injection system insuffi-
cient flow
P2445 82H 01H Secondary air injection system pump
stuck off
P2448 83H 01H Secondary air injection system high
airflow
Bank1: P2440
Bank2: P2442 84H 01H
Secondary air injection system switch-
ing valve stuck open
P2440 85H 01H Secondary air injection system switch-
ing valve stuck open
P2444 86H 01H Secondary air injection system pump
stuck on
FUEL
SYSTEM 81H
Fuel injection system function
(Bank 1) P0171 or P0172 80H 2FH Long term fuel trim
P0171 or P0172 81H 24H The number of lambda control
clamped
P117A 82H 03H Cylinder A/F imbalance monitoring
82H Fuel injection system function
(Bank 2) P0174 or P0175 80H 2FH Long term fuel trim
P0174 or P0175 81H 24H The number of lambda control
clamped
P117B 82H 03H Cylinder A/F imbalance monitoring
Item
OBD-
MID Self-diagnostic test item DTC Test value and Test
limit
(GST display) Description
TID Unit and
Scaling ID
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM