turn signal NISSAN TEANA 2014 Owner's Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2014, Model line: TEANA, Model: NISSAN TEANA 2014Pages: 4801, PDF Size: 51.2 MB
Page 62 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS
BCM (BODY CONTROL MODULE)BCS-47
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
11 5
(R) Ground
Outside key antenna
RH B OutputWhen the front
door RH request
switch is op NISSAN TEANA 2014 Owners Manual
BCS
BCM (BODY CONTROL MODULE)BCS-47
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
11 5
(R) Ground
Outside key antenna
RH B OutputWhen the front
door RH request
switch is op](/img/5/57390/w960_57390-61.png)
BCS
BCM (BODY CONTROL MODULE)BCS-47
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
11 5
(R) Ground
Outside key antenna
RH B OutputWhen the front
door RH request
switch is operat-
ed with push-but-
ton ignition switch
OFF When Intelligent Key is in
the antenna detection area
When Intelligent Key is not
in the antenna detection
area
116
(W) Ground Front console anten-
na A OutputPush-button igni-
tion switch OFF When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
11 7
(SB) Ground Left front flasher Output
Push-button igni-
tion switch ON Turn signal switch OFF 0V
Turn signal switch LH
6.5 V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
JMKIA0062GB
JMKIA0063GB
JMKIA0062GB
JMKIA0063GB
PKID0926E
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 64 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS
BCM (BODY CONTROL MODULE)BCS-49
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
126
(BR) Ground
NATS antenna amp.
B Input/
Output During waiting Intelligent Key backside is NISSAN TEANA 2014 Owners Manual
BCS
BCM (BODY CONTROL MODULE)BCS-49
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
126
(BR) Ground
NATS antenna amp.
B Input/
Output During waiting Intelligent Key backside is](/img/5/57390/w960_57390-63.png)
BCS
BCM (BODY CONTROL MODULE)BCS-49
< ECU DIAGNOSIS INFORMATION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
126
(BR) Ground
NATS antenna amp.
B Input/
Output During waiting Intelligent Key backside is
contacted to push-button
ignition switch, turn ignition
switch ON. Just after pressing push-button
ignition switch. Pointer of analog
volt meter should move.
127 (L) Ground
NATS antenna amp.
A Input/
Output During waiting Intelligent Key backside is
contacted to push-button
ignition switch, turn ignition
switch ON. Just after pressing push-button
ignition switch. Pointer of analog
volt meter should move.
128
(BG) Ground
Front console anten-
na B Output
Push-button igni-
tion switch OFF When Intelligent Key is in
the passenger compart-
ment
When Intelligent Key is not
in the passenger compart-
ment
129 (G) Ground Battery saver output Output After passing the interior room lamp battery sav-
er operation time 0V
Any other time after passing the interior room
lamp battery saver operation time Battery voltage
130
(SB) Ground Passenger door un-
lock Output Front door RH UNLOCK (actuator is acti-
vated) Battery voltage
Other than UNLOCK (actu-
ator is not activated) 0V
131 (W) Ground BCM battery fuse Input Push-button ignition switch OFF Battery voltage
132 (L) Ground Rear door lock Output All doors LOCK (actuator is activat-
ed) Battery voltage
Other than LOCK (actuator
is not activated) 0V
133 (Y) Ground Rear door unlock Output Rear door RH
and rear door LH UNLOCK (actuator is acti-
vated) Battery voltage
Other than UNLOCK (actu-
ator is not activated) 0V
134 (B) Ground Ground 2 — Push-button ignition switch ON 0V
135
(BR) Ground Driver, passenger
and fuel door lock Output All doors LOCK (actuator is activat-
ed) Battery voltage
Other than LOCK (actuator
is not activated) 0V
136 (P) Ground Room lamp control Output Interior room
lamp OFF Battery voltage
ON 0V
Te r m i n a l N o .
(Wire color) Description
Condition Va l u e
(Approx.)
Signal name Input/
Output
(+) (-)
JMKIA0062GB
JMKIA0063GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 67 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS-52
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
DTC Index
INFOID:0000000009462019
NOTE: Details of time display
• CRNT: Displays when there is a malfunction now or after returni NISSAN TEANA 2014 Owners Manual
BCS-52
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
DTC Index
INFOID:0000000009462019
NOTE: Details of time display
• CRNT: Displays when there is a malfunction now or after returni](/img/5/57390/w960_57390-66.png)
BCS-52
< ECU DIAGNOSIS INFORMATION >[BCM]
BCM (BODY CONTROL MODULE)
DTC Index
INFOID:0000000009462019
NOTE: Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni- tion switch OFF → ON again.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter
remains at 39 even if the number of cycles exceeds it . It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
5 • C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL
• C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR
• C1727: [BATT VOLT LOW] RL
• C1730: FLAT TIRE FL
• C1731: FLAT TIRE FR
• C1732: FLAT TIRE RR
• C1733: FLAT TIRE RL
• C1734: CONTROL UNIT
• C1735: IGNITION SIGNAL
6 • B2621: INSIDE ANTENNA
• B2622: INSIDE ANTENNA
7 B259A: ROOM LAMP FUSE
Priority DTC
CONSULT display Fail-safe
Intelligent Key
warning lamp ON Tire pressure
monitor warning lamp ON Reference page
No DTC is detected.
Further testing may be required. —— — —
U1000: CAN COMM CIRCUIT — — — BCS-68, "Description"
U1010: CONTROL UNIT (CAN) — — — BCS-69, "DTC Logic"
U0415: VEHICLE SPEED SIG — — —BCS-70, "Description"
B2190: NATS ANTENNA AMP×—— SEC-84, "Description"
B2191: DIFFERENCE OF KEY ×—— SEC-86, "Description"
B2192: ID DISCORD BCM-ECM ×—— SEC-87, "DTC Logic"
B2193: CHAIN OF BCM-ECM ×—— SEC-88, "DTC Logic"
B2195: ANTI SCANNING ×—— SEC-89, "DTC Logic"
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 82 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS
TRANSIT MODE CANCEL OPERATIONBCS-67
< BASIC INSPECTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
TRANSIT MODE CANCEL OPERATION
DescriptionINFOID:0000000009462026
• BCM is in transit mode if turn NISSAN TEANA 2014 Owners Manual
BCS
TRANSIT MODE CANCEL OPERATIONBCS-67
< BASIC INSPECTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
TRANSIT MODE CANCEL OPERATION
DescriptionINFOID:0000000009462026
• BCM is in transit mode if turn](/img/5/57390/w960_57390-81.png)
BCS
TRANSIT MODE CANCEL OPERATIONBCS-67
< BASIC INSPECTION > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
TRANSIT MODE CANCEL OPERATION
DescriptionINFOID:0000000009462026
• BCM is in transit mode if turn signal indicator on combination meter turns ON for 1 minute when ignition
switch is turned from OFF to ON.
• In this case, cancel operation must be performed.
NOTE:
Do not cancel transit mode during storage of the vehicl e. Always cancel transit mode before delivery of the
vehicle to customer.
Work ProcedureINFOID:0000000009462027
1.TRANSIT MODE CANCEL OPERATION
1. Turn ignition switch OFF.
2. Turn and hold front wiper switch to HI, and then operate turn signal switch to RH or LH.
>> GO TO 2.
2.TRANSIT MODE CANCEL CHECK
1. Turn front wiper switch and turn signal switch OFF.
2. Turn ignition switch ON.
3. Check that turn signal indicator on combination meter does not turn ON.
>> WORK END
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 83 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS-68
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000009462028
Refer to
BCS-7, "BODY CONTROL SYST EM : System Descriptio NISSAN TEANA 2014 Owners Manual
BCS-68
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000009462028
Refer to
BCS-7, "BODY CONTROL SYST EM : System Descriptio](/img/5/57390/w960_57390-82.png)
BCS-68
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U1000 CAN COMM CIRCUIT
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000009462028
Refer to
BCS-7, "BODY CONTROL SYST EM : System Description".
DTC LogicINFOID:0000000009462029
DTC DETECTION LOGIC
NOTE:
U1000 can be set if a module harness was disconnected and reconnected, perhaps during a repair. Confirm
that there are actual CAN diagnostic symptoms and a pr esent DTC by performing the Self Diagnostic Result
procedure.
Diagnosis ProcedureINFOID:0000000009462030
1. PERFORM SELF DIAGNOSTIC RESULT
1. Turn ignition switch ON and wait for 2 second or more.
2. Check “SELF- DIAG RESULTS”.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Perform CAN Diagnosis as described in DIAG NOSIS section of CONSULT Operation Manual.
NO >> Refer to GI-43, "Intermittent Incident"
.
CONSULT Display DTC Detectio n Condition Possible cause
CAN COMM CIRCUIT
[U1000] When any listed module cannot communicate with CAN
communication signal continuously for 2 seconds or
more with ignition switch ON In CAN communication system, any item (or items)
of the following listed below is malfunctioning.
•Transmission
• Receiving (ECM)
• Receiving (VDC/TCS/ABS)
• Receiving (METER/M&A)
• Receiving (TCM)
• Receiving (IPDM E/R)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 85 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS-70
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U0415 VEHICLE SPEED SIG
U0415 VEHICLE SPEED SIG
DescriptionINFOID:0000000009462033
U0415 is displayed if any unusual condition is present in
the reception statu NISSAN TEANA 2014 Owners Manual
BCS-70
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U0415 VEHICLE SPEED SIG
U0415 VEHICLE SPEED SIG
DescriptionINFOID:0000000009462033
U0415 is displayed if any unusual condition is present in
the reception statu](/img/5/57390/w960_57390-84.png)
BCS-70
< DTC/CIRCUIT DIAGNOSIS >[BCM]
U0415 VEHICLE SPEED SIG
U0415 VEHICLE SPEED SIG
DescriptionINFOID:0000000009462033
U0415 is displayed if any unusual condition is present in
the reception status of the vehicle speed signal from
the ABS actuator and electric unit (control unit).
DTC LogicINFOID:0000000009462034
DTC DETECTION LOGIC
NOTE:
• If DTC U0415 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
BCS-68, "DTC Logic"
.
• If DTC U0415 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-69, "DTC Logic"
.
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase the DTC.
2. Turn ignition switch OFF.
3. Perform Self Diagnostic Result of BCM with CONSULT, after the ignition switch has been turned ON for 2 seconds or more.
Is any DTC detected?
YES >> Refer to BCS-52, "DTC Index".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000009462035
1. ABS ACTUATOR AND ELECTRIC UNIT (CON TROL UNIT) SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of ABS with CONSULT. Refer to BRC-33, "CONSULT Function (ABS)"
.
Is any DTC detected?
YES >> Perform the trouble diagnosis relat ed to the detected DTC. Refer to BRC-45, "DTC Index".
NO >> GO TO 2.
2. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND
CIRCUIT
Check ABS actuator and electric unit (control unit) power and ground. Refer to BRC-70, "Diagnosis Proce-
dure".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3. COMBINATION METER SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of METER M&A with CONSULT. Refer to MWI-18, "CONSULT Function
(METER/M&A)".
Is any DTC detected?
YES >> Perform the trouble diagnosis relat ed to the detected DTC. Refer to MWI-27, "DTC Index".
NO >> Refer to GI-43, "Intermittent Incident"
.
CONSULT Display DTC Detectio n Condition Possible Cause
VEHICLE SPEED SIG
[U0415] When the vehicle speed signal received from the
ABS actuator and electric unit (control unit) remains
abnormal for 2 seconds or more. • ABS system
• Combination meter system
• CAN bus harness
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 87 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS-72
< DTC/CIRCUIT DIAGNOSIS >[BCM]
B259A ROOM LAMP FUSE
B259A ROOM LAMP FUSE
DTC LogicINFOID:0000000009462038
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase DTC.
2. NISSAN TEANA 2014 Owners Manual
BCS-72
< DTC/CIRCUIT DIAGNOSIS >[BCM]
B259A ROOM LAMP FUSE
B259A ROOM LAMP FUSE
DTC LogicINFOID:0000000009462038
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase DTC.
2.](/img/5/57390/w960_57390-86.png)
BCS-72
< DTC/CIRCUIT DIAGNOSIS >[BCM]
B259A ROOM LAMP FUSE
B259A ROOM LAMP FUSE
DTC LogicINFOID:0000000009462038
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. DTC CONFIRMATION
1. Erase DTC.
2. Turn ignition switch OFF.
3. Perform the Self Diagnostic Result of BCM with CONSULT, after the ignition switch has been turned ON for 2 minutes or more.
Is any DTC detected?
YES >> Refer to BCS-72, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis ProcedureINFOID:0000000009462039
Regarding Wiring Diagram information, refer to BCS-55, "Wiring Diagram".
1. CHECK FUSE
Check that the following fuse is not blown.
Is the fuse or fusible link blown?
YES >> Replace the blown fuse after repairing the affected circuit.
NO >> GO TO 2.
2. CHECK BAT BCM FUSE CIRCUIT
1. Disconnect BCM connector M21.
2. Check voltage between BCM connector M21 terminal 131 and ground.
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO >> Repair or replace harness or connectors. GO TO 3.
3. CHECK BATTERY SAVER OUTPUT CIRCUIT FOR SHORT TO GROUND
1. Turn ignition OFF.
2. Check continuity between BCM connector M21 terminal 129 and ground.
CONSULT Display DTC Detectio n Condition Possible cause
ROOM LAMP FUSE
[B259A] When BCM detects that power supply voltage is sup-
plied to fusible link battery power, but not to BCM bat-
tery fuse for 2 minutes when ignition switch is ON. Harness or connector (power supply circuit)
Terminal No. Signal name Fuse No.
131 BCM battery fuse 1 (10A)
BCM GroundVo l ta g e
(Approx.)
Connector Terminal
M21 131 — Battery voltage
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 90 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS
COMBINATION SWITCH INPUT CIRCUITBCS-75
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
COMBINATION SWITCH
INPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000009462041
Regarding Wirin NISSAN TEANA 2014 Owners Manual
BCS
COMBINATION SWITCH INPUT CIRCUITBCS-75
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
COMBINATION SWITCH
INPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000009462041
Regarding Wirin](/img/5/57390/w960_57390-89.png)
BCS
COMBINATION SWITCH INPUT CIRCUITBCS-75
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
COMBINATION SWITCH
INPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000009462041
Regarding Wiring Diagram information, refer to BCS-55, "Wiring Diagram".
1. CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM connector M18 and combination switch connector.
3. Check continuity between BCM connecto r M18 and combination switch connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connectors.
2. CHECK INPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT
Check continuity between BCM connector M18 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3. CHECK BCM OUTPUT VOLTAGE
1. Connect BCM connector M18 and combination switch connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M18 and ground.
Signal BCM Combination switch
Continuity
Connector Terminal Connector Terminal
INPUT 1
M1879
M28 11
Ye s
INPUT 2 78 9
INPUT 3 77 7
INPUT 4 76 10
INPUT 5 75 13
Signal BCM
GroundContinuity
Connector Terminal
INPUT 1
M1879
No
INPUT 2 78
INPUT 3 77
INPUT 4 76
INPUT 5 75
Signal BCM
Ground Voltage
Connector Terminal
INPUT 1
M18 79
—Refer to
BCS-31, "Ref-
erence Value".
INPUT 2 78
INPUT 3 77
INPUT 4 76
INPUT 5 75
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 92 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS
COMBINATION SWITCH OUTPUT CIRCUITBCS-77
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
COMBINATION SWITCH
OUTPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000009462042
Regarding Wir NISSAN TEANA 2014 Owners Manual
BCS
COMBINATION SWITCH OUTPUT CIRCUITBCS-77
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
COMBINATION SWITCH
OUTPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000009462042
Regarding Wir](/img/5/57390/w960_57390-91.png)
BCS
COMBINATION SWITCH OUTPUT CIRCUITBCS-77
< DTC/CIRCUIT DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
COMBINATION SWITCH
OUTPUT CIRCUIT
Diagnosis ProcedureINFOID:0000000009462042
Regarding Wiring Diagram information, refer to BCS-55, "Wiring Diagram".
1. CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR OPEN
1. Turn ignition switch OFF.
2. Disconnect BCM connector M17 and combination switch connector.
3. Check continuity between BCM connecto r M17 and combination switch connector.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace harness or connectors.
2. CHECK OUTPUT 1 - 5 SYSTEM CIRCUIT FOR SHORT
Check continuity between BCM connector M17 and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connectors.
3. CHECK BCM INPUT VOLTAGE
1. Connect BCM connector M17 and combination switch connector.
2. Turn ignition switch ON.
3. Check voltage between BCM connector M17 and ground.
Signal BCM Combination switch
Continuity
Connector Terminal Connector Terminal
OUTPUT 1
M1714
M28 12
Ye s
OUTPUT 2 13 14
OUTPUT 3 12 5
OUTPUT 4 11 2
OUTPUT 5 10 8
Signal BCM
GroundContinuity
Connector Terminal
OUTPUT 1
M1714
No
OUTPUT 2 13
OUTPUT 3 12
OUTPUT 4 11
OUTPUT 5 10
Signal BCM
Ground Voltage
Connector Terminal
OUTPUT 1
M1714
—Refer to
BCS-31, "Ref-
erence Value".
OUTPUT 2 13
OUTPUT 3 12
OUTPUT 4 11
OUTPUT 5 10
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM
Page 94 of 4801
![NISSAN TEANA 2014 Owners Manual
BCS
COMBINATION SWITCH SYSTEM SYMPTOMSBCS-79
< SYMPTOM DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom TableINFOID:0000000009462043
1. P NISSAN TEANA 2014 Owners Manual
BCS
COMBINATION SWITCH SYSTEM SYMPTOMSBCS-79
< SYMPTOM DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom TableINFOID:0000000009462043
1. P](/img/5/57390/w960_57390-93.png)
BCS
COMBINATION SWITCH SYSTEM SYMPTOMSBCS-79
< SYMPTOM DIAGNOSIS > [BCM]
C
D E
F
G H
I
J
K L
B
A
O P
N
SYMPTOM DIAGNOSIS
COMBINATION SWITCH SYSTEM SYMPTOMS
Symptom TableINFOID:0000000009462043
1. Perform the data monitor of CONSULT to check for any malfunctioning item.
2. Check the malfunction combinations.
Malfunction item: ×
3. Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction combination Data monitor item
FR WIPER HI
FR WIPER LOW
FR WASHER SW
FR WIPER INT/AUTO INT VOLUME
TURN SIGNAL R
TURN SIGNAL L TA I L L A M P S W
HI BEAM SW
HEAD LAMP SW 1
HEAD LAMP SW 2
PASSING SW
AUTO LIGHT SW FR FOG SW
A ×× ××
B ×× ××
C ×××
D ×× ×
E ××
F ××
G ××
H ×× ×
I ××××
J × ×××
K All Items L If only one item is detected or the item is not applicable to the combinations A to K
Malfunction
combination Malfunctioning part Repair or replace
A Combination switch INPUT 1 circuit
Inspect the combination switch input circuit applicable to the malfunctioning
part. Refer to BCS-75, "Diagnosis Procedure"
.
B Combination switch INPUT 2 circuit
C Combination switch INPUT 3 circuit
D Combination switch INPUT 4 circuit E Combination switch INPUT 5 circuitF Combination switch OUTPUT 1 circuit
Inspect the combination switch output circuit applicable to the malfunction-
ing part. Refer to BCS-77, "Diagnosis Procedure"
.
G Combination switch OUTPUT 2 circuit
H Combination switch OUTPUT 3 circuit I Combination switch OUTPUT 4 circuit
J Combination switch OUTPUT 5 circuit
K BCM Replace BCM. Refer to BCS-80, "Removal and Installation"
.
L Combination switch Replace the combination switch.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM