mirror NISSAN TEANA 2014 Repair Manual

DOOR MIRRORMIR-11
< WIRING DIAGRAM >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
ABLIA5203GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

MIR-12
< WIRING DIAGRAM >
DOOR MIRROR
ABLIA5193GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

INSIDE MIRRORMIR-19
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
REMOVAL AND INSTALLATION
INSIDE MIRROR
Exploded ViewINFOID:0000000009463529
Removal and InstallationINFOID:0000000009463530
REMOVAL
1. Remove the inside mirror base screw.
2. Disconnect the harness connector from the inside mirror.
3. Slide the inside mirror upward and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Apply Genuine Mirror Adhesive or equivalent to bonding surface of mirror base. Refer to GI-21, "Rec-
ommended Chemical Products and Sealants".
1. Inside mirror harness 2. I nside mirror 3. Mirror base
A. Screw
ALLIA1157ZZ
ALKIA0069GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

MIR-20
< REMOVAL AND INSTALLATION >
DOOR MIRROR
DOOR MIRROR
Exploded ViewINFOID:0000000009463531
Removal and InstallationINFOID:0000000009463532
REMOVAL
1. Remove the front door finisher. Refer to INT-15, "Removal and Installation".
2. Disconnect the harness connectors (A) from the door mirror cor- ner finisher.
3. Release the clips and pawls using a suitable tool and remove the door mirror corner finisher (1).
• Push suitable trim tool underneath finisher, and then pry out- ward as shown. Move tool further up near upper fastened
area, and then pry outward again.
: Clip
: Pawl
1. Door mirror cover 2. Side turn signal lamp (if equipped) 3. Door mirror housing assembly
4. Door mirror actuator 5. Door mirror glass and holder
ALLIA1166ZZ
AWLIA2218ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR MIRRORMIR-21
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
4. Remove the door mirror nuts (A) and the door mirror assembly (1).
INSTALLATION
Installation is in the reverse order of removal. Door mirror nut: : 5.1 N·m (0.5 kg-m, 4 ft-lb)
ALLIA1161ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

MIR-22
< REMOVAL AND INSTALLATION >
DOOR MIRROR GLASS
DOOR MIRROR GLASS
Removal and InstallationINFOID:0000000009463533
REMOVAL
1. Position the door mirror glass surface upward.
2. Apply protective tape (A) to mirror housing.
3. Insert a suitable tool (B) as shown and gently release the door mirror glass (1) from the door mirror actuator.
CAUTION:
Do not use excessive force or damage or breakage of the
door mirror glass could occur.
INSTALLATION
Installation is in the reverse order of removal.
AWLIA1999ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR MIRROR REAR FINISHERMIR-23
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
DOOR MIRROR REAR FINISHER
Removal and InstallationINFOID:0000000009463534
REMOVAL
1. Remove the door mirror glass. Refer to MIR-22, "Removal and Installation".
2. Release the door mirror rear finisher pawls (A) using a suitable tool.
3. Remove the door mirror rear finisher.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installation, check that pawls are securely engaged.
ALLIA1175ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

MIR-24
< REMOVAL AND INSTALLATION >
DOOR MIRROR ACTUATOR
DOOR MIRROR ACTUATOR
Removal and InstallationINFOID:0000000009463535
REMOVAL
1. Remove the door mirror glass. Refer to MIR-22, "Removal and Installation".
2. Remove the mirror actuator screw (A).
3. Release the door mirror actuator pawls (A) using a suitable tool. : Pawl
4. Disconnect the harness connector fr om the door mirror actuator
(1) and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALLIA1169ZZ
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

DOOR MIRROR REMOTE CONTROL SWITCHMIR-25
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K
M A
B
MIR
N
O P
DOOR MIRROR REMOTE CONTROL SWITCH
Removal and InstallationINFOID:0000000009463536
REMOVAL
1. Release the pawls and remove the front door pull handle outer finisher. Refer to INT-15, "Exploded View".
2. Disconnect the harness connector from the door mirror remote control switch.
3. Release the pawls and remove the door mirror remote control switch from the front door finisher.
INSTALLATION
Installation is in the reverse order of removal.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

MWI
NORMAL OPERATING CONDITIONMWI-81
< SYMPTOM DIAGNOSIS >
C
D E
F
G H
I
J
K L
M B
A
O P
NORMAL OPERATING CONDITION
COMPASS
COMPASS : DescriptionINFOID:0000000009461756
COMPASS
• The electronic compass is highly protected from changes in most magnetic fields. However, some large
changes in magnetic fields can affect it. Some exampl es are (but not limited to): high tension power lines,
large steel buildings, subways, steel bridges, automatic car washes, large piles of scrap metal, etc. While
this does not happen very often, it is possible.
• During normal operation, the Compass Mirror will cont inuously update the compass calibration to adjust for
gradual changes in the vehicle's magnetic "remnant" field. If the vehicle is subjected to high magnetic influ-
ences, the compass may appear to indicate false headings , become locked, or appear that it is unable to be
calibrated. If this occurs, perform the calibration procedure.
• If at any time the compass continually displays the inco rrect direction or the reading is erratic or locked, ver-
ify the correct zone variance.
Symptom Chart
Symptom Cause Solution / Reference
The compass display reads "C".
• Compass is not calibrated.
• Incorrect zone variance setting.
• Large change in magnetic field (Steel bridges, subways, concentrations of
metal, car washes, etc.)
• Compass was calibrated incorrectly or
in the presence of a strong magnetic
field. Perform Calibration. Refer to
MWI-16,
"COMPASS : Description".
Compass shows the wrong direction.
Compass does not change direction ap-
pears "Locked".
Compass does not show all the directions,
one or more is missing.
The compass was calibrated but it "loses"
calibration.
On long trips the compass shows the
wrong direction. Perform Zone Variatio
n Setting if correct
reading is desired in that location. Refer to
MWI-16, "COMPASS : Description"
.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM