battery NISSAN TEANA 2014 Service Manual

PG
INSPECTION AND ADJUSTMENTPG-7
< BASIC INSPECTION >
C
D E
F
G H
I
J
K L
B
A
O P
N
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REMOVI
NG BATTERY NEGATIVE TERMINAL
ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Spe-
cial Repair Requirement
INFOID:0000000009460434
Required Procedure After Battery Disconnection
System Item Reference
Engine Control System Idle Air Volume Learning EC-179
(QR25DE)
EC-683
(VQ35DE)
Power Window Control System Power Window System Initialization PWC-27
(LH Only Anti-Pinch)
PWC-93
(LH & RH Front Anti-Pinch)
Roof Moonroof Memory Reset/Initialization RF-20
Heater & Air Conditioning Control SystemTemperature Setting Trimmer
HAC-50
(Automatic Air Conditioner)
Foot Position Setting Trimmer HAC-50
(Automatic Air Conditioner)
Inlet Port Memory Function (FRE) HAC-50
(Automatic Air Conditioner)
Inlet Port Memory Function (REC) HAC-51
(Automatic Air Conditioner)
Target Evaporator Temp Upper Limit HAC-51
(Automatic Air Conditioner)
Audio, Visual & Navigation System Audio (Radio Preset) Refer to Owner's Manual.
Navigation System Refer to Owner's Manual.
Revision: November 20132014 Altima NAM

PG-8
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY ROUTING CIRCUIT
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY ROUTING CIRCUIT
Wiring Diagram —Battery Power Supply —INFOID:0000000009460435
ABMWA2171GB
Revision: November 20132014 Altima NAM

PG
HARNESSPG-43
< DTC/CIRCUIT DIAGNOSIS >
C
D E
F
G H
I
J
K L
B
A
O P
N
ENGINE ROOM HARNESS
AAMIA0023ZZ
F2 E2 W/8 : To E202 D1 E25 GR/5 : Front wiper motor
G2 E3 W/10 : To F1 E2 E27 B/3 : Vacuum sensor
F 2 E 4 B R / 2 : F u s i b l e l i n k b o x ( B a t t e r y ) F 3 E 31 GR/32 : ECM (QR25DE for California)
F2 E5 GR/2 : Fusible link box (Battery) G3 E32 GR/32 : ECM (With VQ35DE)
E2 E9 — : Body ground B2 E33 — : Body ground
Revision: November 20132014 Altima NAM

PG-44
< DTC/CIRCUIT DIAGNOSIS >
HARNESS
F3 E10 GR/32 : ECM (QR25DE except for California) B3 E41 GR/2 : Front wheel sensor RH
F2 E11 W/16 : To F2 F1 E42 BR/6 : Cooling fan relay-2
F2 E12 W/6 : To E203 G2 E43 BR/6 : Cooling fan relay-3
F2 E13 Y/4 : To E205 B2 E54 B/38 : ABS actuator and electric unit (Control
unit)
E2 E15 — : Body ground G2 E5 7 L / 4 : S t o p l a m p r e l a y
E1 E16 B/2 : IPDM E/R (Intelligent power distribution
module engine room) C3 E59 B/6 : Power steering control module
E1 E17 W/4 : IPDM E/R (Intelligent power distribution
module engine room) C4 E60 B/2 : Power steering control module
E1 E18 W/12 : IPDM E/R (Intelligent power distribution
module engine room) B3 E61 — : Body ground
E1 E19 GR/2 : Front wheel sensor LH F2 E62 B/1 : Fusible link box (Battery)
F 1 E 2 1 G R / 6 : J o i n t c o n n e c t o r - E 0 3 F 1 E 6 3 W / 3 2 : IPDM E/R (Intelligent power distribution
module engine room)
F1 E22 GR/6 : Joint connector-E04 E1 E73 BR/3 : Outside warning buzzer
F2 E23 BR/8 : To F25 E1 E74 BR/3 : Intelligent Key warning buzzer
D1 E24 GR/2 : Brake fluid level switch
Revision: November 20132014 Altima NAM

PG-48
< DTC/CIRCUIT DIAGNOSIS >
HARNESS
ENGINE CONTROL HARNESS (QR25DE)
AAMIA0026ZZ
F 4 F 2 W / 1 6 : To E 11 D 3 F 3 7 G R / 3: Ignition coil no. 4 (With power
transistor)
B5 F3 B/2 : A/C compressor A1 F40 B/2 : Intake manifold tuning valve motor
F3 F4 — : Fusible link box (Battery) D2 F41 B/2 : Intake manifold runner control valve
motor
G5 F5 GR/4 : Battery current sensor C2 F42 B/4 : Heated oxygen sensor 2
Revision: November 20132014 Altima NAM

PG-50
< DTC/CIRCUIT DIAGNOSIS >
HARNESS
ENGINE CONTROL HARNESS (VQ35DE)
ABMIA5144ZZ
G4 F1 W/10 : To E3 E5 F48 B/10 : Joint connector-F02
F4 F2 W/16 : To E11 G5 F49 B/10 : Joint connector-F03
A4 F3 B/2 : A/C compressor F5 F50 B/10 : Joint connector-F04
F3 F4 — : Fusible link box (Battery) G3 F53 W/4 : Joint connector-F07
G5 F5 GR/4 : Battery current sensor D4 F56 B/4 : Heated oxygen sensor 2 (Bank 2)
Revision: November 20132014 Altima NAM

PG
BATTERYPG-73
< REMOVAL AND INSTALLATION >
C
D E
F
G H
I
J
K L
B
A
O P
N
REMOVAL AND INSTALLATION
BATTERY
Exploded ViewINFOID:0000000009460448
Removal and Installation (Battery)INFOID:0000000009460449
REMOVAL
1. Remove cover of battery positive terminal.
2. Loosen battery terminal nuts and disconnect bot h positive and negative battery terminals.
CAUTION:
Disconnect the negative battery terminal first.
3. Remove battery frame nuts, battery frame and battery rods.
4. Remove battery cover.
5. Remove battery.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Connect the positive battery terminal first.
1. Upper ECM bracket 2. Battery frame 3. Battery
4. Battery rods 5. Battery tray cover 6. Battery tray liner
7. Battery tray 8. Battery tray support Front
AWMIA1279ZZ
Battery terminal nut : 5.4 N·m (0.55 kg-m, 48 in-lb)
Revision: November 20132014 Altima NAM

PG-74
< REMOVAL AND INSTALLATION >
BATTERY
Reset electronic systems as necessary. Refer to PG-7, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Special Repair Requirement".
Removal and Installation (Battery Tray)INFOID:0000000009460450
REMOVAL
1. Remove battery and battery tray liner. Refer to PG-73, "Removal and Installation (Battery)".
2. Remove front air duct and air cleaner case assembly. Refer to EM-29, "Removal and Installation"
(QR25DE models) or EM-144, "Removal and Installation" (VQ35DE models).
3. Disconnect transmission control module (TCM). Refer to TM-183, "Exploded View"
(RE0F10D) TM-384,
"Exploded View"or (RE0F10E).
4. Remove the ECM bracket.
5. Remove the battery tray bolts and battery tray.
6. Remove the battery tray support bolts and battery tray support.
INSTALLATION
Installation is in the reverse order of removal.
Reset electronic systems as necessary. Refer to PG-7, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Special Repair Requirement".
Revision: November 20132014 Altima NAM

PG
BATTERYPG-75
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D E
F
G H
I
J
K L
B
A
O P
N
SERVICE DATA AND SPECIFICATIONS (SDS)
BATTERY
BatteryINFOID:0000000009460451
*: Always check with the Parts Department for the latest parts information.
Typ e*
GR27 GR35
Capacity (20HR) minimum V-AH 12-80 12-60
Cold cranking current A @ -18 °C (0 °F) 710 550
Revision: November 20132014 Altima NAM

PWC-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D E
F
G H
I
J
L
M
SECTION PWC
A
B
PWC
N
O P
CONTENTS
POWER WINDOW CONTROL SYSTEM
LH FRONT ONLY ANTI-PINCH
PRECAUTION ................ ...............................
6
PRECAUTIONS .............................................. .....6
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ............................................................. ......
6
Precaution for Work ..................................................6
PREPARATION ............................................7
PREPARATION .............................................. .....7
Special Service Tool ........................................... ......7
SYSTEM DESCRIPTION ..............................8
COMPONENT PARTS ................................... .....8
Component Parts Location ................................ ......8
Component Description .............................................8
SYSTEM .............................................................10
System Diagram ................................................. ....10
System Description .................................................10
Fail-safe ..................................................................11
DIAGNOSIS SYSTEM (BCM) ............................13
COMMON ITEM ..................................................... ....13
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) ................................................. ....
13
RETAINED PWR ................................................... ....14
RETAINED PWR : CONSULT Function (BCM -
RETAINED PWR) ............................................... ....
14
ECU DIAGNOSIS INFORMATION ..............15
BCM (BODY CONTROL MODULE) ............... ....15
List of ECU Reference ........................................ ....15
POWER WINDOW MAIN SWITCH ....................16
Reference Value ................................................. ....16
WIRING DIAGRAM ......................................18
POWER WINDOW SYSTEM .............................18
Wiring Diagram - With Left Front Only Power Win-
dow Anti- Pinch .................................................... ....
18
BASIC INSPECTION ...................................25
DIAGNOSIS AND REPAIR WORKFLOW ........25
Work Flow ............................................................ ....25
INSPECTION AND ADJUSTMENT ..................27
ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL ............................... ....
27
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Description . ....
27
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Special Re-
pair Requirement ................................................. ....
27
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT .................................................... ....
27
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ............................. ....
27
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .. ....
27
DTC/CIRCUIT DIAGNOSIS .........................29
POWER SUPPLY AND GROUND CIRCUIT ....29
BCM ....................................................................... ....29
BCM : Diagnosis Procedure ....................................29
POWER WINDOW MAIN SWITCH ........................ ....29
POWER WINDOW MAIN SWITCH : Description ....29
POWER WINDOW MAIN SWITCH : Component
Function Check .................................................... ....
30
POWER WINDOW MAIN SWITCH : Diagnosis
Procedure ............................................................ ....
30
POWER WINDOW MAIN SWITCH : Component
Inspection ............................................................ ....
33
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM