mirror NISSAN TERRANO 2004 Service User Guide
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2004, Model line: TERRANO, Model: NISSAN TERRANO 2004Pages: 1833, PDF Size: 53.42 MB
Page 1620 of 1833

YEL121D
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER
Wiring Diagram Ð DEF Ð (Cont'd)EL-127
http://vnx.su/
Page 1621 of 1833

Trouble Diagnoses
SYMPTOM CHART
SymptomDiagnoses service procedure
Rear window defogger and door mirror defogger do not activate. 1. Check time control unit power supply and ground circuit. 2. Check rear window defogger switch.
3. Check rear window defogger switch circuit.
4. Check rear window defogger signal.
5. Check rear window defogger relay.
Rear window defogger or door mirror defogger do not activate. 1. Check fuse (No. 14, No. 15 or No. 1). 2. Check filament.
3. Check harness between fuse block (J/B) and defogger.
4. Check defogger ground circuit.
Rear window defogger and door mirror defogger do not go off
after activating about 15 minutes. 1. Check time control unit power supply and ground circuit.
2. Check rear window defogger switch.
3. Check rear window defogger switch circuit.
POWER SUPPLY AND GROUND CIRCUIT CHECK
Main power supply circuit check
Terminals
Ignition switch position
!@ OFF ACC ON
U09GroundBattery
voltage Battery
voltage Battery
voltage
U01Ground ÐÐBattery
voltage
Ground circuit check
Terminals Continuity
U16- GroundYes
YEL888E
YEL300D
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER
EL-128
http://vnx.su/
Page 1622 of 1833

CHECK REAR WINDOW DEFOGGER SWITCH
1. Disconnect A/C control panel connector(rear window defogger switch)
M771.
2. Check continuity between terminals q
3
andq5.
With rear window defogger switch ON:
Continuity should exist.
With rear window defogger switch OFF:
Continuity should not exist.
OK
ENG Replace rear window
defogger switch.
Rear window defogger switch is OK.
CHECK REAR WINDOW DEFOGGER SWITCH CIRCUIT
1. Check continuity between fuse block
(J/B) connector terminal
M19and A/C
control panel connector terminal q
3.
Continuity should exist.
2. Check continuity between fuse block (J/B) connector terminal
M19and
ground.
Continuity should not exist.
OK
ENG Repair harness or connec-
tor.
1. Check continuity between A/C control
panel connector terminal q
5and
ground.
Continuity should exist.
OK
ENG Repair harness or connec-
tor.
Rear window defogger switch circuit is
OK.
YEL889E
YEL890E
YEL891E
H
H
H
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER
Trouble Diagnoses (Cont'd)
EL-129
http://vnx.su/
Page 1623 of 1833

CHECK REAR WINDOW DEFOGGER SIGNAL
1. Check voltage between fuse block(J/B) terminal
M19and ground.
With rear window defogger switch ON: Approx. 0V
With rear window defogger switch OFF: Battery voltage
OK
ENG Replace time control unit.
1. Disconnect time control unit.
2. Ignition switch ON.
3. Check voltage between time control unit terminal
U13and ground.
Battery voltage should exist.
OK
ENG Replace time control unit.
Rear window defogger signal is OK.
CHECK REAR WINDOW DEFOGGER RELAY
1. Check voltage between fuse block
(J/B) terminals
BM1,M26and ground.
With rear window defogger switch ON: Battery voltage
OK
ENG Replace rear window relay.
Rear window defogger relay is OK.
YEL892E
YEL893E
YEL894E
H
H
H
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER
Trouble Diagnoses (Cont'd)
EL-130
http://vnx.su/
Page 1624 of 1833

CHECK REAR WINDOW/DOOR MIRROR DEFOGGER
CIRCUIT
CHECK REAR WINDOW DEFOGGER
CIRCUIT.
1. Disconnect rear window defogger con-nector.
2. Check continuity between rear window defogger connector terminal 1and fuse
block (J/B) terminal
BM1.
Continuity should exist.
3. Check continuity between rear window defogger connector terminal q
2and
ground.
Continuity should not exist.
OK
ENG Repair or replace harness.
CHECK DOOR MIRROR DEFOGGER
CIRCUIT.
1. Disconnect door mirror defogger con-
nector.
2. Check continuity between door mirror defogger connector terminal q
3and
fuse block (J/B) terminal
M26.
Continuity should exist.
3. Check continuity between door mirror defogger connector terminal q
2and
ground.
Continuity should exist.
OK
ENG Repair or replace harness.
Rear window defogger and door mirror
defogger circuit is OK.
YEL895E
YEL896E
YEL897E
YEL898E
H
H
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER
Trouble Diagnoses (Cont'd)
EL-131
http://vnx.su/
Page 1625 of 1833

Filament Check
1. Attach probe circuit tester (in volt range) to middle portion ofeach filament.6 volts = Normal filament
2. If a filament is burned out, circuit tester registers 0 or 12 volts.
3. To locate burned out point, move probe to left and right along filament to determine point where tester needle swings
abruptly.
I When measuring voltage, wind a piece of tin foil around
the top of the negative probe and press the foil against the
wire with your finger.
SEL263
SEL265
SEL266
YEL553D
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER
EL-132
http://vnx.su/
Page 1626 of 1833

Filament Repair
REPAIR EQUIPMENT
1. Conductive silver composition (Dupont No. 4817 or equivalent)
2. Ruler 30 cm (11.8 in) long
3. Drawing pen
4. Heat gun
5. Alcohol
6. Cloth
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with acloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of drawing pen.
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive sil- ver composition on break with drawing pen. Slightly overlap
existing heat wire on both sides [preferably 5 mm (0.20 in)] of
the break.
4. After repair has been completed, check repaired wire for con- tinuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5. Apply a constant stream of hot air directly to the repaired area for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area
and hot air outlet. If a heat gun is not available, let the repaired
area dry for 24 hours.
BE540
SEL012D
SEL013D
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER
EL-133
http://vnx.su/
Page 1647 of 1833

Wiring Diagram Ð MIRROR Ð
LHD MODELS
YEL136D
DOOR MIRROR
EL-154
http://vnx.su/
Page 1648 of 1833

RHD MODELS
YEL137D
DOOR MIRROR
Wiring Diagram Ð MIRROR Ð (Cont'd)EL-155
http://vnx.su/
Page 1709 of 1833

System Description
The TCU (Time Control Unit) has the following functions.
INTERIOR LAMP TIMER
The interior lamp timer is controlled by the TCU.
The TCU keeps the interior lamp illuminated for about 30 seconds when:
Ithe ignition key is turned from ªONº to ªACCº to ªLOCKº
I the driver's door is unlocked
I a door is opened and then closed while the ignition switch is in the ªOFFº position. (Interior lamp switch
in the ªDOORº position).
The timer is canceled when:
I driver's door is locked, or
I ignition switch is turned ªONº.
IGNITION KEY WARNING CHIME AND LIGHT WARNING CHIME
The ignition key and light warning chime are controlled by the TCU.
The warning chime is combined with the TCU.
The light warning chime will not sound, when ignition switch is in the ªONº or ªSTARTº position. (When power
supply exists at TCU terminal
U01.)
With ignition switch in the OFF position, driver's door open, and lighting switch in 1ST or 2ND position, warn-
ing chime will sound.
Or, with the key in the ignition switch in the ªACCº or ªOFFº position, and locking the driver's door from the
outside, the warning buzzer will sound.
REAR WINDOW DEFOGGER TIMER
The rear window defogger and door mirror defogger system are controlled by the TCU.
The rear window and door mirror defogger operate only for approximately 15 minutes.
POWER DOOR LOCK (Super Lock)
The power door lock (super lock) is controlled by the TCU.
For further information, refer to ªPOWER DOOR LOCK Ð Super Lockº (EL-179).
MULTI-REMOTE CONTROL SYSTEM
The multi-remote control system is controlled by the TCU.
When the following input signals are both supplied:
I Key switch OFF (when ignition key is not inserted in key cylinder);
I door switch CLOSED (when all the doors are closed);
The two above signals are already input into time control unit. At this point, time control unit receives a LOCK
signal from remote controller. Time control unit locks all doors and set super lock with input of LOCK signal
from remote controller.
When an UNLOCK signal is sent from remote controller once, driver's door will be unlocked and release super
lock.
Then, if an UNLOCK signal is sent from remote controller again, all other door will be unlocked.
MULTI-REMOTE CONTROLLER ID CODE ENTRY
For detailed procedure, refer to ªID Code Entry Procedureº (EL-215).
THEFT WARNING SYSTEM
The theft warning system is controlled by the TCU.
For further information, refer to ªTHEFT WARNING SYSTEMº (EL-243).
TIME CONTROL UNIT (TCU)
EL-216
http://vnx.su/