light NISSAN TITAN 2018 Owner´s Manual

∙Do not expose the CD to direct sun-
light.
∙ CDs that are in poor condition or are
dirty, scratched or covered with fin-
gerprints may not work properly.
∙ The following CDs may not work
properly:
∙ Copy control compact discs (CCCD)
∙ Recordable compact discs (CD-R)
∙ Rewritable compact discs (CD-RW)
∙ Do not use the following CDs as they
may cause the CD player to malfunc-
tion:
∙ 3.1 in (8 cm) discs with an adapter
∙ CDs that are not round
∙ CDs with a paper label
∙ CDs that are warped, scratched, or
have abnormal edges
∙ This audio system can only play pre-
recorded CDs. It has no capability to
record or burn CDs.
∙ If the CD cannot be played, one of the
following messages will be displayed. CHECK DISC
∙
Confirm that the CD is inserted cor-
rectly (the label side is facing up,
etc.).
∙ Confirm that the CD is not bent or
warped and it is free of scratches.
PRESS EJECT
This is an error due to excessive tem-
perature inside the player. Remove
the CD by pressing the EJECT button.
Af ter a short time, reinsert the CD.
The CD can be played when the tem-
perature of the player returns to nor-
mal.
UNPLAYABLE
The file is unplayable in this audio
system (only MP3 or WMA CD).Compact disc with MP3 or WMA
Terms ∙ MP3 — MP3 is short for Moving Pictures Experts Group Audio Layer 3. MP3 is the
most well-known compressed digital
audio file format. This format allows for
near “CD quality” sound, but at a fraction
of the size of normal audio files. MP3
conversion of an audio track from CD-
ROM can reduce the file size by approxi-
mately a 10:1 ratio with virtually no per-
ceptible loss in quality. MP3
compression removes the redundant
and irrelevant parts of a sound signal
that the human ear doesn’t hear.
∙
WMA — Windows Media Audio (WMA)* is a
compressed audio format created by Mi-
crosof t as an alternative to MP3. The WMA
codec offers greater file compression
than the MP3 codec, enabling storage of
more digital audio tracks in the same
amount of space when compared to
MP3s at the same level of quality.
∙ Bit rate — Bit rate denotes the number of bits per second used by a digital mu-
sic file. The size and quality of a com-
pressed digital audio file is determined
by the bit rate used when encoding the
file.
Monitor, climate, audio, phone and voice recognition systems4-51

To turn the system off, press the(power) button.
Turn the VOL (volume) control knob to ad-
just the volume.This vehicle may be equipped with Speed
Sensitive Volume. When this feature is ac-
tive, the audio volume changes as the driv-
ing speed changes.
ENTER/SETTING button
Press the ENTER/SETTING button to show
the Settings screen on the display. Turn the
TUNE/FOLDER knob to navigate the op-
tions and then press the ENTER/SETTING
button to make a selection.
Audio
Bluetooth Adjusts Bluetooth® settings.
Bass Adjusts the bass to the desired level.
Treble Adjusts the treble to the desired level.
Balance Adjusts the balance to the desired level. Balance adjusts the sound level between the lef t and right speakers.
Fade Adjusts the fade to the desired level. Fade adjusts the sound level between the front and rear speakers.
Brightness and Contrast Adjust the brightness or contrast to adjust the appearance of the display screen.
Clock adjust Press the ENTER/SETTING button to highlight the hours or minutes and then use the TUNE/FOLDER knob to adjust the value. Press the ENTER/SETTING button again to set the value.
On-Screen Clock Toggles ON or OFF the clock display on the upper right corner of the display screen.
RDS Display Toggles ON or OFF the RDS information displayed on the screen while the radio is playing.
Speed Sensitive Vol. (volume) Adjusts the speed sensitive volume function, which increases the volume of the audio system as the speed of the vehicle increases. Set to “OFF” to disable the feature. The higher the setting, the more the volume in-
creases in relation to vehicle speed.
AUX Vol. Choose a setting from 0 to +3 to control the boost of incoming auxiliary device volume. A setting of 0 pro- vides no additional boost in volume. A setting of +3 provides the greatest boost in volume.
Language select Select the desired language for the system from the available options.
Auto Source Change Select ON or OFF for Auto Source Change. With Auto Source Change ON: when device is plugged into USB port, radio will automatically switch to USB source. With Auto Source Change OFF: when device is plugged into
USB port, radio will stay on currently selected source.
Bass, treble, balance and fade can also be adjusted by pressing the ENTER/SETTING button and turning the TUNE/FOLDER control knob
to select the item to adjust. When the desired item is shown on the display, turn the tuning to adjust and then press the ENTER/SETTING
button until the display returns to the main audio screen. If the button is not pressed, the radio or CD display will automatically reappear.
4-58Monitor, climate, audio, phone and voice recognition systems

ENTER/SETTING button
Press the ENTER/SETTING button to show
the Settings screen on the display. Turn the
TUNE/SCROLL knob to navigate the op-
tions and then press the ENTER/SETTING
button to make a selection.
AudioBluetooth Adjusts Bluetooth® settings
Bass Adjusts the bass to the desired level.
Treble Adjusts the treble to the desired level.
Balance Adjusts the balance to the desired level. Balance adjusts the sound level between the lef t and right speakers.
Fade Adjusts the fade to the desired level. Fade adjusts the sound level between the front and rear speakers.
Brightness Adjust the brightness to adjust the appearance of the display screen.
Contrast Adjust the contrast to adjust the appearance of the display screen.
Clock adjust Press the ENTER/SETTING button to highlight the hours or minutes and then use the TUNE/SCROLL knob to adjust the value. Press the ENTER/SETTING button again to set the value.
On-Screen Clock Toggles ON or OFF the clock display on the upper right corner of the display screen.
RDS Display Toggles ON or OFF the RDS information displayed on the screen while the radio is playing.
Speed Sens Vol. (Speed Sensitive Volume) Adjusts the speed sensitive volume function, which increases the volume of the audio system as the speed of the vehicle increases. Set to “OFF” to disable the feature. The higher the setting, the more the volume in-
creases in relation to vehicle speed.
AUX Vol. Choose a setting from 0 to +3 to control the boost of incoming auxiliary device volume. A setting of 0 pro- vides no additional boost in volume. A setting of +3 provides the greatest boost in volume.
Language Select Select the desired language for the system from the available options.
Auto Source Change Select ON or OFF for Auto Source Change. With Auto Source Change ON: when device is plugged into USB port, radio will automatically switch to USB source. With Auto Source Change OFF: when device is plugged into
USB port, radio will stay on currently selected source.
Bass, treble, balance and fade can also be adjusted by pressing the ENTER/SETTING button and turning the TUNE/SCROLL control knob
to select the item to adjust. When the desired item is shown on the display, turn the tuning to adjust and then press the ENTER/SETTING
button until the display returns to the main audio screen. If the button is not pressed for approximately 10 seconds, the radio or CD display
will automatically reappear.
Monitor, climate, audio, phone and voice recognition systems4-63

CD/MP3 display mode
Menu item
CD/MP3 display mode While listening to a CD or an MP3/WMA CD, certain text may be displayed (when a CD encoded
with text is being used). Depending on how the CD or MP3/WMA CD is encoded, the text is dis-
played listing the artist, album and song title. There are other keys displayed on the screen when
aCDisplaying:
Random Touch the “Random” key to apply a random play pattern to the CD. If an MP3 CD is playing, touch-
ing “Random” key alternates between the Random Folder and Random All. This text will appear on
the display. To cancel random mode, touch the “Random” key until the key is no longer
highlighted.
Repeat Touch the “Repeat” key to apply a repeat play pattern to the CD. If an MP3 CD is playing, touching
“Repeat” alternates between repeating the current song and repeating the current folder. This text
will appear on the display. To cancel repeat mode, touch the “Repeat” key until the key is no longer
highlighted
Browse Touch the “Browse” key to display the titles on the CD in list format. Touch the title of a song in the
list to begin playing that song. If an MP3 CD is playing, touching the “Browse” key will also list the
folders on the disc. Follow the procedure for selecting a song with the touch-screen to choose a
folder.
Monitor, climate, audio, phone and voice recognition systems4-73

WARNING
∙ The Mobile Entertainment System isdesigned for rear seat passenger
viewing only.
∙ It is unlawful in most jurisdictions for a person to drive a motor vehicle
which is equipped with a television
viewer or screen that is located in the
motor vehicle at any point forward of
the back of the driver’s seat, or that is
visible, directly or indirectly, to the
driver while operating the vehicle.
∙ In the interest of safety, the monitors should never be installed where they
will be visible, directly or indirectly, by
the operator of the motor vehicle.
∙ If your vehicle is equipped with a wire- less rear seat audio system or any
other wireless infrared device, make
sure it is powered off when operating
the Rear Seat Entertainment System.
If both systems are powered on at the
same time, the two systems may ob-
struct each other, possibly creating
undesirable audio interference
through the wireless headphones. ∙ For safety reasons, when changing
video discs it is recommended that
the vehicle is not in motion, and that
you do not allow children to unfasten
safety belts to change discs or make
any adjustments to the system. Sys-
tem adjustments can be accom-
plished using the remote control unit,
while safety belts remain fastened.
CAUTION
∙ Be sure to run the vehicle engine whileusing the system. Using this system
without running the engine can result
in a battery drain. To avoid the risk of
battery drain, please remember to
turn off the system when the vehicle
is not in use. Do not touch the inner
pins of the jacks on the front panel.
Electrostatic discharge may cause
permanent damage to the system.
NOTE:
Depending on the USB device, it may or
may not charge when connected to the
USB connection port. Not all devices are
able to charge when connected to the
USB connection port. Each monitor includes a built-in dual chan-
nel infrared transmitter for use with wire-
less headphones. The wireless head-
phones must be used within a line of sight
from the transmitter as infrared transmis-
sion, like visible light, travels only in a
straight line.
When placing the headphones on your
head, make sure to observe the Lef t and
Right orientation. The headphones must
be oriented correctly (facing forward) in or-
der to receive the audio signal. Press the
power button on the headphones, then se-
lect channel “A” to listen to monitor A, or
channel “B” to listen to monitor B. Adjust the
audio level using the volume control on
each headphone.
There is a 3.5mm stereo headphone out-
put jack on each monitor which can be
used with any standard stereo headphone
with an in-line volume control (wired head-
phones sold separately).
The system includes a built-in infrared re-
ceiver for use with the included wireless
remote control. For additional information,
refer to “Remote control operation” in this
section.
NISSAN MOBILE ENTERTAINMENT
SYSTEM (MES) (if so equipped)
Monitor, climate, audio, phone and voice recognition systems4-93

1. Status lights
2. Disc Compartment Slot
3. IR Sensor/Transmitter
4. Monitor Adjustment
5. TFT LCD Panel
6. USB Port7. Audio Video Output Jack
8. Headphone Output Jack
9. Audio Video Input Jacks
10. I/O Port Covers
11. Lever Lock and Release Latch
FRONT PANEL BUTTONS
CAUTION
∙ Do not use any harsh solvents or
chemicals when cleaning the unit.
∙ Do not use any abrasive cleaners that may scratch the screen. Use only a
lightly dampened lint free cloth to
wipe the screen if it is dirty.
∙ Position LCD monitor in the fully closed position when not in use.
∙ Before using the monitor, ensure lever lock and release latch is engaged in
the normal viewing position
A.
∙ Do not put pressure on the screen.
∙ Caution children to avoid touching the screen, as it may become dirty or
damaged.
Status lights
The status lights illuminate if there is no
disc present in the unit.LHA3804
4-94Monitor, climate, audio, phone and voice recognition systems

Regional coding
Both the DVD player and discs are coded by
region. These regional codes must match
in order for the disc to play. The system is
preset to the region code designated for
your area by the DVD Copy Control Asso-
ciation. Other regions may not be played in
this system.
Supported Disc Types∙ DVD-Video: DVD contains video
∙ DVD +/- R: DVD contains video
∙ CD-DA: CD contains audio
∙ CD-Video: CD contains video
∙ CD-R/+RW: CD contains audio
Unsupported Disc Types
Before you load a disc, make sure that it is
compatible with the player. Note that the
following disc CANNOT be used with this
system: Optical disc- CD-1, CD-ROM, and
DVD-ROM Mini disc- CDG (audio only, not
graphics), and Blu-ray (list is not all inclu-
sive).
Loading and Playing Discs
Press the POWER button to turn the moni-
tor on. Insert the disc about half way into the disc compartment slot, with the disc’s
label facing the rear of the vehicle. Do NOT
insert the disc at an angle. The Disc must
be inserted straight into the player.
The disc will load automatically and begin
to play. Some discs may start at the root
menu, where playback must be selected to
start a movie. Depending on the disc and
playback location on the disc, a “
”icon
may be displayed in the upper lef t-hand
corner of the screen indicating that play-
back is not possible during certain times.
Additional information on Media
Compatibility
This system is compatible with the follow-
ing media formats:
Format Extension
Audio MP3 .mp3
WMA .wma
Video AVI
.avi
MPEG-1 .mpg
MPEG-2 .mpg
Image JPEG .jpg
Due to ongoing technological advance-
ments, some USB flash drives may be in-
compatible with this system. ∙ The text information of some audio and
video files may not be correctly dis-
played.
∙ There may be a slight delay before play- back of files using a USB flash drive with
complex folder hierarchies.
∙ Some audio, video, and image files may be incompatible with this system due
to file characteristics, file format, record-
ing sof tware used, directory structure,
and/or the type of audio/video encod-
ing used.
HOW TO USE THE DVD OSD MENU
This section describes how to set and ad-
just settings using On-Screen Display
(OSD) Menu. You can use the OSD menu to
adjust all the settings. Follow the steps out-
lined below to select the desired function.
Monitor, climate, audio, phone and voice recognition systems4-103

General Setup Page
Press the SETUP button on the remote
control. Use the
orand
the
orbuttons to navi-
gate the Setup Page. Press ENTER to select
and then
to return to the sub-
–menu. To cancel the Setup Display, press
the SETUP button on the remote.
OSD Language
The OSD Lang sub-menu allows the user to
select the language for the on-screen dis-
play. When the OSD Lang option is high-
lighted, press the
button once
and then use the
orbut-
tons on the remote control to select the
desired language. The user can select Eng-
lish, Simplified/Traditional Chinese, French,
German, Italian, Spanish, Portuguese, or
Korean for the OSD language. Press ENTER
to select and then the
button to
return to the sub-menu.
Angle Mark
The angle mark is an option for different
viewing angles on the DVD. When the Angle
Mark option is highlighted, press
the
button once and then use
the
orbuttons on the re-
mote control to turn the angle mark set-
ting on or off. Press ENTER to select and
then the
button to return to the
sub-menu.
LHA3851LHA3852LHA3853
4-104Monitor, climate, audio, phone and voice recognition systems

Speaker Setup Page
Downmix— When the Downmix option is
highlighted, press the
button
once and then use the
orbuttons on the remote control
to select between Stereo or LT/RT. Press
ENTER to select and then the
but-
ton to return to the sub-menu.
Video Setup Page
Video Quality — When the Quality option is
highlighted, press ENTER and then use
the
orand the
orbuttons on the remote control
to select between the various video quality
settings. Press ENTER to select and then
the
button to return to the sub-
menu.
Video Quality Setup
Option Description Range De-
fault
Sharpness Adjust to
sof ten or
sharpen the picture. Low/
Med/ High Low
Brightness Adjust to
brighten or darken the picture. -20 —
+20 00
LHA3854LHA3855LHA3856
Monitor, climate, audio, phone and voice recognition systems4-105

Option Description RangeDe-
fault
Contrast Adjust to in-
crease or de- crease pic-
ture contrast. -16 —
+16 00
Gamma Adjust to in-
crease or de- crease the picture
gamma. Low/
Med/
High/ None None
Hue Adjust to in-
crease or de- crease thecolor hue. -09 —
+09 00
Saturation Adjust to in-
crease or de- crease color intensity. -09 —
+09 00
Luma De- lay Adjust to
change the
Luma delay. 0T or 1T 1T
Preference Page
If a disc or USB device is playing, press STOP
twice (full stop). Press the SETUP button on
the remote control. Use the
orand theorbuttons on the remote control to navigate
the Setup Page. Press ENTER to select and
then the
to return to the sub-
menu.
Audio
The Audio sub-menu allows the user to
select the audio stream in the desired lan-
guage for playback. When the Audio option
is highlighted, press the
button
once and then use the
orbuttons on the remote control
to select the desired language. The user
can select English, French, Spanish, Chi-
nese, Japanese, German, Portuguese, Ital-
ian, Korean, Russian or Thai for the audio
stream language. Press ENTER to select
and then the
button to return to
the sub-menu. The DVD title must include
LHA3857LHA3858
4-106Monitor, climate, audio, phone and voice recognition systems