lock NISSAN VERSA 2006 Workshop Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2006, Model line: VERSA, Model: NISSAN VERSA 2006Pages: 2896, PDF Size: 64.73 MB
Page 2259 of 2896
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-51
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
TURN SIGNAL AND HAZARD WARNING LAMPSPFP:26120
Component Parts and Harness Connector LocationEKS00HXZ
System DescriptionEKS00HY0
TURN SIGNAL OPERATION
Power is supplied at all times
through 40A fusible link (letter g , located in the fuse and fusible link box)
to BCM (body control module) terminal 70,
through 10A fuse [No. 8, located in the fuse block (J/B)]
to BCM terminal 57,
through 10A fuse [No. 13, located in the fuse block (J/B)]
to combination meter terminal 27.
With the ignition switch in the ON or START position, power is supplied
through 10A fuse [No. 6, located in fuse block (J/B)]
to BCM terminal 38,
through 10A fuse [No. 3, located in fuse block (J/B)]
to combination meter terminal 28.
With the ignition switch in the ACC or ON position, power is supplied
through 10A fuse [No. 20, located in the fuse block (J/B)]
to BCM terminal 11.
Ground is supplied
to BCM terminal 67 and
to combination meter terminals 21, 22 and 23
through grounds M57 and M61.
LH Turn Signal Lamp
When the turn signal switch is moved to the left turn position, the BCM receives an input signal requesting left
turn signals to flash. The BCM then supplies power
through BCM terminal 60
to front combination lamp LH terminal 4 and
to rear combination lamp LH terminal 6.
1. BCM M18 and M20 (view with glove
box removed)2. Hazard switch M55 3. Combination switch (lighting switch)
M28
4. Combination meter M24
WKIA5493E
Page 2260 of 2896
LT-52
TURN SIGNAL AND HAZARD WARNING LAMPS
Revision: June 20062007 Versa
Ground is supplied
to front combination lamp LH terminal 5
through grounds E15 and E24,
to rear combination lamp LH terminal 1
through grounds B7 and B19.
The BCM also sends a request, via the CAN communication lines, to the combination meter to flash the left
turn signal indicator. The unified meter control unit in the combination meter supplies ground to the left turn
signal indicator lamp and activates the audible turn signal indicator.
With power, ground and input supplied, the BCM controls the flashing of the turn signal lamps.
RH Turn Signal Lamp
When turn signal switch is moved to the right turn position, the BCM receives an input signal requesting right
turn signals to flash. The BCM then supplies power
through BCM terminal 61
to front combination lamp RH terminal 4 and
to rear combination lamp RH terminal 6.
Ground is supplied
to front combination lamp RH terminal 5
through grounds E15 and E24,
to rear combination lamp RH terminal 1
through grounds B117, B132 and B402.
The BCM also sends a request, via the CAN communication lines, to the combination meter to flash the right
turn signal indicator. The unified meter control unit in the combination meter supplies ground to the right turn
signal indicator lamp and activates the audible turn signal indicator.
With power, ground and input supplied, the BCM controls the flashing of the turn signal lamps.
HAZARD LAMP OPERATION
Power is supplied at all times
through 40A fusible link (letter g , located in fuse, fusible link and relay box)
to BCM terminal 70,
through 10A fuse [No. 8, located in fuse block (J/B)]
to BCM terminal 57,
through 10A fuse [No. 13, located in fuse block (J/B)]
to combination meter terminal 27.
Ground is supplied
to hazard switch terminal 1,
to BCM terminal 67, and
to combination meter terminals 21, 22 and 23
through grounds M57 and M61.
When hazard switch is depressed, ground is supplied
through hazard switch terminal 2
to BCM terminal 29.
BCM then supplies power
to front combination lamp LH terminal 4 and
to rear combination lamp LH terminal 6
through BCM terminal 60,
to front combination lamp RH terminal 4 and
to rear combination lamp RH terminal 6
through BCM terminal 61.
Ground is supplied
to front combination lamp LH and RH terminal 5
through grounds E15 and E24,
Page 2261 of 2896
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-53
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
to rear combination lamp LH terminal 1
through grounds B7 and B19,
to rear combination lamp RH terminal 1
through grounds B117, B132 and D402.
The BCM also supplies input to combination meter across the CAN communication lines. This input is pro-
cessed by unified meter control unit in combination meter, which in turn supplies ground to the left and right
turn signal indicator lamps.
With power and input supplied, BCM controls flashing of hazard warning lamps.
REMOTE KEYLESS ENTRY SYSTEM OPERATION
Power is supplied at all times
through 40A fusible link (letter g , located in fuse, fusible link and relay box)
to BCM terminal 70,
through 10A fuse [No. 13, located in fuse block (J/B)]
to combination meter terminal 27.
Ground is supplied
to BCM terminal 67 and
to combination meter terminals 21, 22 and 23
through grounds M57 and M61.
When the remote keyless entry system is triggered by input from the keyfob, the BCM supplies power
through BCM terminal 60
to front combination lamp LH terminal 4 and
to rear combination lamp LH terminal 6,
through BCM terminal 61
to front turn signal lamp RH terminal 4 and
to rear combination lamp RH terminal 6.
Ground is supplied
to front combination lamp LH and RH terminals 5
through grounds E15 and E24,
to rear combination lamp LH terminal 1
through grounds B7 and B19,
to rear combination lamp RH terminal 1
through grounds B117, B132 and D402.
The BCM also supplies input to combination meter via the CAN communication lines. This input is processed
by the unified meter control unit in combination meter, which in turn supplies ground to the left and right turn
signal indicator lamps.
With power and ground supplied, BCM controls flashing of hazard warning lamps when keyfob is used to acti-
vate remote keyless entry system.
COMBINATION SWITCH READING FUNCTION
Refer toBCS-3, "COMBINATION SWITCH READING FUNCTION" .
CAN Communication System DescriptionEKS00HY1
Refer to LAN-4, "CAN Communication System" .
Page 2283 of 2896
PARKING, LICENSE PLATE AND TAIL LAMPS
LT-75
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
PARKING, LICENSE PLATE AND TAIL LAMPSPFP:26550
Component Parts and Harness Connector LocationEKS00HYY
System DescriptionEKS00HYZ
The control of the parking, license plate and tail lamp operation is dependent upon the position of lighting
switch. When the lighting switch is placed in the 1ST position, the BCM (body control module) receives input
signal requesting the parking, license plate and tail lamps to illuminate. This input signal is communicated to
the IPDM E/R (intelligent power distribution module engine room) via the CAN communication lines. The CPU
(central processing unit) located in the IPDM E/R controls the tail lamp relay coil. This relay, when energized,
directs power to parking, license plate and tail lamps, which then illuminate.
Power is supplied at all times
to ignition relay located in IPDM E/R,
to tail lamp relay located in IPDM E/R,
through 15A fuse (No. 52, located in IPDM E/R) and
through 20A fuse (No. 53, located in IPDM E/R)
to the CPU located in the IPDM E/R,
through 40A fusible link (letter g , located in fuse and fusible link block)
to BCM terminal 70,
through 10A fuse [No. 8, located in fuse block (J/B)],
to BCM terminal 57.
With the ignition switch in the ON or START position, power is supplied
through 10A fuse [No. 6, located in fuse block (J/B)]
to BCM terminal 38,
to ignition relay located in IPDM E/R and
through the ignition relay
to the CPU of the IPDM E/R.
With the ignition switch in the ACC or ON position, power is supplied
through 10A fuse [No. 20, located in fuse block (J/B)]
to BCM terminal 11.
Ground is supplied
to BCM terminal 67
through grounds M20 and M61,
to IPDM E/R terminals 59 and 39
through grounds E15 and E24.
OPERATION BY LIGHTING SWITCH
With the lighting switch in the 1ST or 2ND position, the BCM receives an input signal requesting parking,
license plate and tail lamps to illuminate. This input signal is communicated to the IPDM E/R via the CAN com-
munication lines. The CPU, located in the IPDM E/R, controls the tail lamp relay coil. When energized, the tail
lamp relay directs power
1. IPDM E/R E45, E46 and E48 2. BCM M18 and M20 (view with glove
box removed)3. Combination switch (lighting switch)
M28
WKIA5554E
Page 2294 of 2896
LT-86
PARKING, LICENSE PLATE AND TAIL LAMPS
Revision: June 20062007 Versa
Bulb ReplacementEKS00HZC
PA R K I N G L A M P
Refer to LT- 8 7 , "Bulb Replacement" .
LICENSE PLATE LAMP
1. Remove the license plate lamp. Refer to LT- 8 6 , "LICENSE PLATE LAMP" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb from the socket.
4. Installation is in the reverse order of removal.
TA I L L A M P
Refer to LT- 8 7 , "Bulb Replacement" .
Removal and InstallationEKS00HZD
PA R K I N G L A M P
Refer to LT- 8 7 , "Removal and Installation" .
LICENSE PLATE LAMP
Removal
1. Press the license plate lamp pawl on the side of the rear bumper fascia, then swing the license plate lamp
down to release the license plate lamp hook from the rear bumper fascia.
2. Disconnect the license plate lamp connector and remove the licence plate lamp.
Installation
Installation is in the reverse order of removal.
TA I L L A M P
Refer to LT- 8 7 , "Removal and Installation" .
1. License plate lamp A. Pawl B. Hook
LKIA0759E
Page 2295 of 2896
REAR COMBINATION LAMP
LT-87
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
REAR COMBINATION LAMPPFP:26554
ComponentsEKS00IBB
Bulb ReplacementEKS00HZE
1. Remove the rear combination lamp. Refer to LT- 8 7 , "Removal and Installation" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationEKS00HZF
REMOVAL
1. Remove rear combination lamp nuts.
2. Pull the rear combination lamp toward rear of the vehicle and remove from the vehicle.
3. Disconnect rear combination lamp connector, and remove rear combination lamp.
INSTALLATION
Installation is in the reverse order of removal.
Disaassembly and AssemblyEKS00IBC
DISSASEMBLY
1. Remove the rear combination lamp harness.
2. Remove the bulbs from the rear combination lamp housing assembly.
3. Remove the bumper stay.
1. Rear combination lamp harness 2. Turn signal lamp bulb 3. Back-up lamp bulb
4. Stop/tail lamp bulb 5. Rear combination lamp housing
assembly6. Bumper stay
A. Grommet B. Nut C. Clip
D. Nuts E. Clip
LKIA0760E
Page 2299 of 2896
INTERIOR ROOM LAMP
LT-91
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
INTERIOR ROOM LAMPPFP:26410
Component Parts and Harness Connector LocationEKS00HZJ
System DescriptionEKS00HZK
When room lamp switch is in DOOR position, room lamp ON/OFF is controlled by timer according to signals
from switches including key switch, front door switch LH, unlock signal from keyfob, door lock and unlock
switch, key cylinder lock and unlock switch, ignition switch.
When room lamp turns ON, there is a gradual brightening over 1 second.
When room lamp turns OFF, there is a gradual dimming over 1 second.
Interior room lamp timer is controlled by BCM (body control module).
Interior room lamp timer control settings can be changed with CONSULT-II.
POWER SUPPLY AND GROUND
Power is supplied at all times (without Intelligent Key system)
through 10A fuse [No. 14, located in fuse block (J/B)]
to key switch and key lock solenoid terminal 2,
through 10A fuse [No. 8, located in fuse block (J/B)]
to BCM terminal 57,
through 40A fusible link (letter g , located in fuse and fusible link box)
to BCM terminal 70.
Power is supplied at all times (with Intelligent Key system)
through 10A fuse (No. 31, located in fuse and fusible link box)
to key switch and ignition knob switch terminals 2 and 4,
through 10A fuse [No. 8, located in fuse block (J/B)]
to BCM terminal 57,
through 40A fusible link (letter g , located in fuse and fusible link box)
to BCM terminal 70.
When key is inserted in the key switch and key lock solenoid, power is supplied (without Intelligent Key sys-
tem)
through key switch and key lock solenoid terminal 1
to BCM terminal 37.
1. BCM M18, M19 and M20 (view with
glove box removed)2. Key switch and key lock solenoid
(without Intelligent Key) M273. Key switch and ignition knob switch
(with Intelligent Key) M73
4. Front door switch LH B8 and RH
B1085. Rear door switch LH B6 and RH
B1166. Front door key cylinder switch LH
D14
WKIA5545E
Page 2300 of 2896
LT-92
INTERIOR ROOM LAMP
Revision: June 20062007 Versa
When key is inserted in the key switch and ignition knob switch, power is supplied (with Intelligent Key system)
through key switch and ignition knob switch terminal 1
to BCM terminal 37.
When ignition knob switch is pushed, power is supplied (with Intelligent Key system)
through key switch and ignition knob switch terminal 3
to Intelligent Key unit terminal 27.
With the ignition switch in the ON or START position, power is supplied
through 10A fuse [No. 6, located in fuse block (J/B)]
to BCM terminal 38.
Ground is supplied
to BCM terminal 67
through grounds M57 and M61.
When front door LH is opened, ground is supplied
to BCM terminal 47
through front door switch LH terminal 2
through case ground of front door switch LH.
When front door RH is opened, ground is supplied
to BCM terminal 12
through front door switch RH terminal 2
through case ground of front door switch RH.
When rear door LH is opened, ground is supplied
to BCM terminal 48
through rear door switch LH terminal 1
through case ground of rear door switch LH.
When rear door RH is opened, ground is supplied
to BCM terminal 13
through rear door switch RH terminal 1
through case ground of rear door switch RH.
When back door is opened, ground is supplied
to BCM terminal 43
through back door lock assembly (back door switch) terminal 3
through back door lock assembly (back door switch) terminal 4
through grounds B117, B132 and D402.
When front door LH is unlocked by front door key cylinder switch LH, the BCM receives a ground signal
to BCM terminal 7
through front door key cylinder switch LH terminal 3
through front door key cylinder switch LH terminal 2
through grounds M57 and M61.
When a signal, or combination of signals is received by BCM, ground is supplied
to room lamp terminal 2
through map lamp terminals 5 and 2 (with map lamp)
through BCM terminal 63.
With power and ground supplied, the interior room lamp illuminates.
SWITCH OPERATION
When map lamp switch is ON (with map lamp), ground is supplied
through grounds M57 and M61.
to map lamp terminal 1
Power is supplied
Page 2301 of 2896
INTERIOR ROOM LAMP
LT-93
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
through BCM terminal 56
to map lamp terminal 4.
When interior room lamp switch is ON, ground is supplied
to interior room lamp terminal 1
through map lamp (with map lamp) terminal 7
through map lamp (with map lamp) terminal 1
through grounds M57 and M61.
Power is supplied
through BCM terminal 56
through map lamp (with map lamp) terminal 4
through map lamp (with map lamp) terminal 6
to room lamp terminal 3.
INTERIOR ROOM LAMP TIMER OPERATION
Without Intelligent Key System
When room lamp switch is in DOOR position, and when all conditions below are met, BCM performs timer
control (maximum 30 seconds) for room lamp ON/OFF.
In addition, when the interior room lamp turns ON or OFF there is gradual brightening or dimming over 1 sec-
ond.
Power is supplied
through 10A fuse [No. 14, located in fuse block (J/B)]
to key switch and key lock solenoid terminal 2.
When the key is removed from ignition key cylinder (key switch OFF), power will not be supplied to BCM termi-
nal 37.
When front door key cylinder switch LH is unlocked, ground is supplied
to BCM terminal 7
through front door key cylinder switch LH terminal 3
through front door key cylinder switch LH terminal 2
through grounds M57 and M61.
At the time that front door LH is opened, BCM detects that front door LH is unlocked. It determines that interior
room lamp timer operation condition is met, and turns the room lamp ON for 30 seconds.
When key is in ignition key cylinder (key switch ON),
Power is supplied
through key switch and key lock solenoid terminal 1
to BCM terminal 37.
When key is removed from key switch and key lock solenoid (key switch OFF), the power supply to BCM ter-
minal 37 is terminated. BCM detects that key has been removed, determines that interior room lamp timer
conditions are met, and turns the room lamp ON for 30 seconds.
When front door LH opens → closes, and the key is not inserted in the key switch and key lock solenoid (key
switch OFF), voltage at BCM terminal 47 changes between 0V (door open) → 12V (door closed). The BCM
determines that conditions for room lamp operation are met and turns the room lamp ON for 30 seconds.
Interior room lamp timer control is canceled under the following conditions:
Front door LH is locked (locked front door key cylinder switch LH).
Front door LH is opened (front door switch LH).
Ignition switch ON.
With Intelligent Key System
When the room lamp switch is in DOOR position, and when all conditions below are met, BCM performs timer
control (maximum 30 second) for room lamp ON/OFF.
In addition, when interior room lamp turns ON or OFF there is gradual brightening or dimming over 1 second.
Power is supplied
through 10A fuse (No. 31, located in fuse and fusible link box)
to key switch and ignition knob switch terminals 2 and 4.
Page 2302 of 2896
LT-94
INTERIOR ROOM LAMP
Revision: June 20062007 Versa
When key is removed from ignition key cylinder (key switch OFF), power will not be supplied to BCM terminal
37.
When the ignition knob switch is released, power will not be supplied to Intelligent Key unit terminal 27.
When front door key cylinder switch LH is unlocked, ground is supplied
to BCM terminal 7
through front door key cylinder switch LH terminal 3
through front door key cylinder switch LH terminal 2
through grounds M57 and M61.
At the time the front door LH is opened, the BCM detects the front door LH is unlocked. It determines that the
interior room lamp timer operation conditions are met, and interior room lamp ON for 30 seconds.
When the key is in ignition key cylinder (key switch ON), or ignition knob switch is pushed, power is supplied
through key switch and ignition knob switch terminal 1
to BCM terminal 37, or
through key switch and ignition knob switch terminal 3
to Intelligent Key unit terminal 27.
When the key is removed from key switch (key switch OFF), power supply to BCM terminal 37 is terminated.
When the ignition knob switch is released, power supply to intelligent key unit is terminated. The BCM detects
that the key has been removed, determines that interior room lamp timer conditions are met, and turns room
lamp ON for 30 seconds.
When the front door LH opens → closes, and key is not inserted in key switch (or ignition knob switch is
released), BCM terminal 47 changes between 0V (door open) → 12V (door closed). BCM determines that
conditions for room lamp operation are met, and turns room lamp ON for 30 seconds.
Interior room lamp timer control is canceled under the following conditions:
Front door LH is locked (with keyfob or front door key cylinder switch LH).
Front door LH is opened (front door switch LH).
Ignition switch ON.
INTERIOR LAMP BATTERY SAVER CONTROL
If an interior room lamp is left ON, it will not be turned OFF even when door is closed.
BCM turns off interior lamp automatically to save battery 30 minutes after ignition switch is turned off.
After lamps are turned OFF by the battery saver system, the lamps illuminate again when
front door key cylinder switch LH is locked or unlocked
door is opened or closed
key is removed from ignition key cylinder or inserted in ignition key cylinder, or the ignition knob switch is
pushed or released.
Interior lamp battery saver control time period can be changed by the function setting of CONSULT-II.