window NISSAN VERSA 2006 Workshop Service Service Manual

EI-28
DOOR FINISHER
Revision: June 20062007 Versa
4. Insert a trim stick (A) or suitable tool into back edge of front door
power window and door lock/unlock switch finisher. Lift upward
to release the clips and remove.
5. Disconnect front door power window and door lock/unlock
switch harness connector.
6. Remove the (2) front door finisher screws.
7. Release the clips, then lift front door finisher upward to remove it
from door body panel.
Installation
Installation is in the reverse order of removal.
WIIA1237E
PIIB6042E
SIIA0810E

DOOR FINISHER
EI-29
C
D
E
F
G
H
J
K
L
MA
B
EI
Revision: June 20062007 Versa
REAR DOOR
Removal
1. Open rear door and rear door window.
2. Disconnect the negative battery cable.
3. Release the rear door inside handle escutcheon pawls, then
slide the escutcheon rearward to remove from rear door finisher.
4. Insert a trim stick (A), or suitable tool into back edge of rear door
power window switch finisher. Lift upward to release the clips
and remove.
1. Rear power window switch finisher 2. Rear door finisher 3. Inside handle escutcheon
Clip C101
LIIA2573E
PIIB6040E
WIIA1238E

EI-30
DOOR FINISHER
Revision: June 20062007 Versa
5. Disconnect rear door power window switch harness connector.
6. Remove rear door finisher screw.
7. Release the clips, then lift rear door finisher upward to remove it
from door body panel.
Installation
Installation is in the reverse order of removal.
SIIA0810E

SERVICE INFORMATION FOR ELECTRICAL INCIDENT
GI-29
C
D
E
F
G
H
I
J
K
L
MB
GI
Revision: June 20062007 Versa
An unclamped or loose harness can cause wiring to be pinched by seat components (such as slide guides)
during vehicle vibration. If the wiring runs under seating areas, inspect wire routing for possible damage or
pinching.
Heat Sensitive
The customer's concern may occur during hot weather or after car
has sat for a short time. In such cases you will want to check for a
heat sensitive condition.
To determine if an electrical component is heat sensitive, heat the
component with a heat gun or equivalent.
Do not heat components above 60°C (140°F). If incident occurs
while heating the unit, either replace or properly insulate the compo-
nent.
Freezing
The customer may indicate the incident goes away after the car
warms up (winter time). The cause could be related to water freezing
somewhere in the wiring/electrical system.
There are two methods to check for this. The first is to arrange for
the owner to leave his car overnight. Make sure it will get cold
enough to demonstrate his complaint. Leave the car parked outside
overnight. In the morning, do a quick and thorough diagnosis of
those electrical components which could be affected.
The second method is to put the suspect component into a freezer
long enough for any water to freeze. Reinstall the part into the car
and check for the reoccurrence of the incident. If it occurs, repair or
replace the component.
Water Intrusion
The incident may occur only during high humidity or in rainy/snowy
weather. In such cases the incident could be caused by water intru-
sion on an electrical part. This can be simulated by soaking the car
or running it through a car wash.
Do not spray water directly on any electrical components.
Electrical Load
The incident may be electrical load sensitive. Perform diagnosis with
all accessories (including A/C, rear window defogger, radio, fog
lamps) turned on.
Cold or Hot Start Up
On some occasions an electrical incident may occur only when the car is started cold, or it may occur when
the car is restarted hot shortly after being turned off. In these cases you may have to keep the car overnight to
make a proper diagnosis.
SGI842
SGI843
SGI844
SGI845

GI-46
RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS
Revision: June 20062007 Versa
RECOMMENDED CHEMICAL PRODUCTS AND SEALANTSPFP:00000
Recommended Chemical Products and SealantsEAS0021Q
Refer to the following chart for help in selecting the appropriate chemical product or sealant.
Product Description PurposeNissan North America
Part No. (USA)Nissan Canada Part
No. (Canada)Aftermarket Cross-
reference Part Nos.
1Rear View Mirror
AdhesiveUsed to permanently
remount rear view mirrors
to windows.999MP-AM000P 99998-50505 Permatex 81844
2Anaerobic Liquid Gas-
ketFor metal-to-metal flange
sealing.
Can fill a 0.38 mm (0.015
inch) gap and provide
instant sealing for most
powertrain applications.999MP-AM001P 99998-50503Permatex 51813 and
51817
3High Performance
Thread SealantProvides instant sealing on
any threaded straight or
parallel threaded fitting.
(Thread sealant only, no
locking ability.)

Do not use on plastic.999MP-AM002P 999MP-AM002P Permatex 56521
4 Silicone RTVGasket Maker999MP-AM003P
(Ultra Grey)99998-50506
(Ultra Grey)Permatex Ultra Grey
82194;
Three Bond
1207,1215, 1216,
1217F and 1217G;
Nissan RTV Part No.
999MP-A7007
Gasket Maker for Maxima/
Quest 5-speed automatic
transmission
(RE5F22A)––Three Bond 1281B
or exact equivalent
in its quality
5High Temperature,
High Strength Thread
Locking Sealant (Red)Threadlocker 999MP-AM004P 999MP-AM004PPermatex 27200;
Three Bond 1360,
1360N, 1305 N&P,
1307N, 1335,
1335B, 1363B,
1377C, 1386B, D&E
and 1388
6Medium Strength
Thread Locking Seal-
ant (Blue)Threadlocker (service tool
removable)999MP-AM005P 999MP-AM005PPermatex 24200,
24206, 24240,
24283 and 09178;
Three Bond 1322,
1322N, 1324 D&N,
1333D, 1361C,
1364D, 1370C and
1374

GW-1
GLASSES, WINDOW SYSTEM & MIRRORS
I BODY
CONTENTS
C
D
E
F
G
H
J
K
L
M
SECTION GW
A
B
GW
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precautions for Procedures without Cowl Top Cover ..... 3
Handling for Adhesive and Primer ........................... 3
PREPARATION ........................................................... 4
Commercial Service Tools ........................................ 4
SQUEAK AND RATTLE TROUBLE DIAGNOSES ..... 5
Work Flow ................................................................ 5
CUSTOMER INTERVIEW ..................................... 5
DUPLICATE THE NOISE AND TEST DRIVE ....... 6
CHECK RELATED SERVICE BULLETINS ........... 6
LOCATE THE NOISE AND IDENTIFY THE
ROOT CAUSE ...................................................... 6
REPAIR THE CAUSE ........................................... 6
CONFIRM THE REPAIR ....................................... 7
Generic Squeak and Rattle Troubleshooting ........... 7
INSTRUMENT PANEL .......................................... 7
CENTER CONSOLE ............................................. 7
DOORS ................................................................. 7
TRUNK .................................................................. 8
SUNROOF/HEADLINING ..................................... 8
OVERHEAD CONSOLE (FRONT AND REAR) ..... 8
SEATS ................................................................... 8
UNDERHOOD ....................................................... 8
Diagnostic Worksheet .............................................. 9
WINDSHIELD GLASS ...............................................11
Removal and Installation .........................................11
REMOVAL ............................................................11
INSTALLATION ................................................... 12
OPERA WINDOW GLASS ....................................... 13
Removal and Installation ........................................ 13
REMOVAL ........................................................... 13
INSTALLATION ................................................... 13
REAR WINDOW GLASS AND MOLDING ............... 15
Removal and Installation ........................................ 15
REMOVAL ........................................................... 15
INSTALLATION ................................................... 16
POWER WINDOW SYSTEM .................................... 17Component Parts and Harness Connector Location ... 17
System Description ................................................. 17
MANUAL OPERATION ........................................ 18
AUTO OPERATION ............................................. 20
POWER WINDOW LOCK ................................... 21
RETAINED POWER OPERATION ...................... 21
CAN Communication System Description .............. 21
Schematic ............................................................... 22
Wiring Diagram — WINDOW — ............................. 23
Main Power Window and Door Lock/Unlock Switch
Harness Connector Terminal Layout ...................... 27
Terminal and Reference Value for Main Power Win-
dow and Door Lock/Unlock Switch ......................... 27
Terminal and Reference Value for BCM ................. 28
Work Flow ............................................................... 28
CONSULT-II Function (BCM) ................................. 28
CONSULT-II START PROCEDURE .................... 28
ACTIVE TEST ..................................................... 29
WORK SUPPORT ............................................... 29
DATA MONITOR ................................................. 29
Trouble Diagnoses Symptom Chart ....................... 29
BCM Power Supply and Ground Circuit Check ...... 30
Main Power Window and Door Lock/Unlock Switch
Power Supply and Ground Circuit Check ............... 30
Front Power Window Motor LH Circuit Check ........ 32
Front Power Window RH Circuit Check (Power Win-
dow and Door Lock/Unlock Switch RH Operation) ... 33
Front Power Window Motor RH Circuit Check ....... 33
Encoder Circuit Check ............................................ 34
Door Switch Check ................................................. 37
Rear Power Window LH Circuit Check (Rear Power
Window Switch LH Operation) ................................ 38
Rear Power Window RH Circuit Check (Rear Power
Window Switch RH Operation) ............................... 39
Rear Power Window Motor LH Circuit Check ......... 39
Rear Power Window Motor RH Circuit Check ........ 41
FRONT DOOR GLASS AND REGULATOR ............. 43
Removal and Installation ........................................ 43
DOOR GLASS ..................................................... 43
REGULATOR ASSEMBLY .................................. 44

GW-2Revision: June 20062007 Versa Disassembly and Assembly .................................... 45
POWER WINDOW REGULATOR ASSEMBLY ... 45
Inspection after Installation ..................................... 45
POWER WINDOW SYSTEM INITIALIZATION ... 45
INSPECT THE FUNCTION OF THE ANTI-
PINCH SYSTEM .................................................. 46
FITTING INSPECTION ........................................ 46
REAR DOOR GLASS AND REGULATOR ............... 47
Removal and Installation ........................................ 47
DOOR GLASS ..................................................... 47
REGULATOR ASSEMBLY .................................. 48
Disassembly and Assembly .................................... 49
POWER WINDOW REGULATOR ASSEMBLY ... 49
Inspection after Installation ..................................... 49
FITTING INSPECTION ........................................ 49
REAR WINDOW DEFOGGER .................................. 50
Component Parts and Harness Connector Location ... 50
System Description ................................................. 50
CAN Communication System Description .............. 51
Wiring Diagram — DEF — ..................................... 52
Terminals and Reference Value for BCM ................ 54
Terminals and Reference Value for IPDM E/R ........ 54
Work Flow ............................................................... 54
CONSULT-II Function (BCM) .................................. 55CONSULT-II START PROCEDURE .....................55
DATA MONITOR ..................................................55
ACTIVE TEST ......................................................55
Trouble Diagnoses Symptom Chart ........................55
BCM Power Supply and Ground Circuit Check ......56
Rear Window Defogger Switch Circuit Check .........56
Rear Window Defogger Circuit Check ....................57
Door Mirror Defogger Circuit Check ........................60
Filament Check .......................................................61
Filament Repair .......................................................62
REPAIR EQUIPMENT .........................................62
REPAIRING PROCEDURE .................................62
DOOR MIRROR .........................................................64
Wiring Diagram — MIRROR — ..............................64
Removal and Installation .........................................65
REMOVAL ............................................................65
INSTALLATION ....................................................65
Disassembly and Assembly ....................................66
DISASSEMBLY ....................................................66
ASSEMBLY ..........................................................66
INSIDE MIRROR .......................................................67
Removal and Installation .........................................67
REMOVAL ............................................................67
INSTALLATION ....................................................67

GW-12
WINDSHIELD GLASS
Revision: June 20062007 Versa
After removing windshield upper molding, remove glass using piano wire or power cutting tool (A) and an
inflatable pump bag (B).

If a windshield glass is to be reused, mark the body and the glass with mating marks.
WAR NIN G:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:

When a windshield glass is to be reused, do not use a cutting knife or power cutting tool.

Be careful not to scratch the glass when removing.

Do not set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION

Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.

While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger room air pressure when a door is closed.

The molding must be installed securely so that it is in position and leaves no gap.

Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WAR NIN G:

Keep heat and open flames away as primers and adhesive are flammable.

The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.

Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.

Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the windshield in case of an accident.
CAUTION:

Do not use an adhesive which is past its usable term. Shelf life of the adhesive is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.

Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.

Do not leave primers or adhesive cartridge unattended with their caps open or off.

The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidities. The curing time will
increase under lower temperatures and lower humidities.
Repairing Water Leaks
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the windshield area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.
PIIB5779E

OPERA WINDOW GLASS
GW-13
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: June 20062007 Versa
OPERA WINDOW GLASSPFP:76820
Removal and InstallationEIS0094E
REMOVAL
1. Remove the front pillar garnish. Refer to EI-33, "FRONT PILLAR GARNISH" .
2. Remove the instrument side panel. Refer to IP-10, "
INSTRUMENT PANEL ASSEMBLY" .
3. Apply protective tape around the opera window glass to protect the painted surface from damage.

If a opera window glass is to be reused, mark the body and the glass with mating marks.
4. Remove the opera window glass using piano wire or power cutting tool and inflatable pump bag.
WA RN ING:
When cutting the glass from the vehicle, always wear safety glasses and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:

When a opera window glass is to be reused, do not use a cutting knife or power cutting tool.

Be careful not to scratch the glass when removing.

Do not set or stand the glass on its edge. Small chips may develop into cracks.

Clips are molded to the side window glass. Replace the clips with new ones if they are damaged
when removing the side window glass.
INSTALLATION

Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent and follow the instructions fur-
nished with it.
PIIB6286E
1. Opera window glass 2. Adhesive 3. Front pillar garnish
4. Primer

GW-14
OPERA WINDOW GLASS
Revision: June 20062007 Versa

While the urethane adhesive is curing, open a door window. This will prevent the glass from being forced
out by passenger room air pressure when a door is closed.

The opera window glass must be installed securely so that the molding around glass is in position and
leaves no gap.

Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and humidity.
WAR NIN G:

Keep heat and open flames away as primers and adhesive are flammable.

The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Avoid
contact with the skin and eyes.

Use in an open, well ventilated location. Avoid breathing the vapors. They can be harmful if
inhaled. If affected by vapor inhalation, immediately move to an area with fresh air.

Driving the vehicle before the urethane adhesive has completely cured may affect the perfor-
mance of the side window in case of an accident.
CAUTION:

Do not use an adhesive which is past its usable term. Shelf life of the adhesive is limited to six
months after the date of manufacture. Carefully adhere to the expiration or manufacture date
printed on the box.

Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.

Do not leave primers or adhesive cartridge unattended with their caps open or off.

The vehicle should not be driven for at least 24 hours or until the urethane adhesive has com-
pletely cured. Curing time varies depending on temperature and humidities. The curing time will
increase under lower temperature and lower humidity.
Repairing Water Leaks
Leaks can be repaired without removing and reinstalling glass.
If water is leaking between the urethane adhesive material and body or glass, determine the extent of leakage.
This can be done by applying water to the side window area while pushing glass outward.
To stop the leak, apply primer (if necessary) and then urethane adhesive to the leak point.