instrument panel NISSAN VERSA HATCHBACK 2010 1.G Quick Reference Guide

4
STEERING WHEEL SWITCHES FOR AUDIO CONTROL/
BLUETOOTH® (if so equipped)
Press the SOURCE button to turn the audio system on.

To choose Preset A, B, c, cd or A uX press SOURCE
repeatedly.

The tuning up or down
switch can be used to perform

the following:
• Push the

switch for less than 1.5 seconds to change

to a preset station.
• Push and hold the

switch for more than 1.5 seconds

to seek the next or previous broadcasting radio station.
• Push the

switch while playing a cd for less than 1.5 seconds to change tracks on the cd.

Push the + or – control switch to increase or decrease the volume.
HEADLIGHT AND TURN SIGNAL CONTROL
HeAd LiGHT c OnTROL SW iTc H
Turn the headlight control switch
01 to the
position
to turn on the front parking, tail, license plate and instrument
panel lights.

Turn the headlight control switch
01 to the
position
to turn on the headlights. All other lights remain on.
fOG Li GHT OP eRATi On (if so equipped)
nOTe: The headlights must be on and the low beams selected for the fog lights t\
o operate.

Turn the switch (inside collar)
02 to the
position to turn on the fog lights.

Turn the switch (inside collar)
02 to the OFF position to turn off the fog lights.
H
iGH B eAM
Push the headlight control switch forward
A to select the
high beam function. The blue
indicator light illuminates.
Pull the headlight switch back to the original position to
select the low beam function. The blue indicator light
goes off.

Pull and release the headlight control switch
B to flash

the headlight high beams on and off.
0102
A
B

5
CRUISE CONTROL (if so equipped)
To activate cruise control, push the ON/OFF switch. The
indicator light in the instrument panel will illuminate.

To set cruising speed, accelerate the vehicle to the desired
speed, push the COAST/SET switch and release. The
SeT indicator light in the instrument panel will illuminate.

To reset at a faster cruising speed, push and hold the
ACCEL/RES switch. When the vehicle attains the speed
you desire, release the switch.

To reset at a slower cruising speed, push and hold the COAST/SET switch. Release the
switch when the vehicle slows to the desired speed.

To cancel cruise control, push the CANCEL switch or tap the brake pedal. The S eT indicator
light in the instrument panel will go out.

To resume a preset speed, push and release the ACCEL/RES switch. The vehicle returns to
the last set cruising speed when the vehicle speed is over 25 MPH (40 km/h).

To turn off cruise control, push the ON/OFF switch. Both the c Rui Se indicator light and the
SeT indicator light in the instrument panel will go out.
MANUAL CLIMATE CONTROL
01 FAN SPEED CONTROL DIAL

Turn the fan speed control dial to the left (slow) or right (fast) to control fan speed.
02 TEMPERATURE CONTROL DIAL
Turn the temperature control dial to select the desired temperature. Turn the control dial to the
left for cold air or right for hot air.
03 AIR FLOW CONTROL DIAL
Turn the dial to select from the following air flow outlets:

Air flows from the center and side vents.

Air flows from the center, side and foot vents.

Air flows mainly from the foot vents.

Air flows from the defroster and foot vents.

Air flows mainly from the defroster vents.
01
020304
0506
07

9
TWIN TRIP ODOMETER
The twin trip odometer records the distance of two
individual trips.

Press the button
01 to change the display as follows:
Trip A
Trip B
Trip A.

Press and hold the button
01 for more than 1 second
to reset the currently displayed trip odometer to zero.
01
4-SPEED AUTOMATIC TRANSMISSION (if so equipped)
The 4-speed automatic transmission is electronically controlled to produce
maximum power and smooth operation.

The automatic transmission in your vehicle is designed so that the brake
pedal must be depressed before shifting from P (P ARk) to any gear
position while the ignition switch is in the O n position.

The shift lever cannot be moved out of P (P ARk) and into any of the other
gear positions if the ignition is turned to the LO ck position or if the key
is removed.
CONTINUOUSLY VARIABLE TRANSMISSION (CVT) (if so equipped)
The cVT does not produce a gear change
sensation like traditional automatic transmissions.

R (ReVe RSe) speed for cVT vehicles is limited
to 15 MPH (25 km/h).
The transmission in your vehicle requires a special
fluid available only at your ni SSAn dealer. no other
fluid will meet the exact requirements of the cVT.
STARTin G THe enGine W iTH cVT
(ni SSAn intelligent k ey™ models only)
depress the brake pedal.

Push the ignition knob in.

confirm the intelligent k ey system warning light is illuminated green.

Turn the ignition knob to start the engine.
Tu Rnin G TH e enGine O ff WiTH cVT (ni SSAn intelligent k ey™ models only)
Shift the shift lever into the P (P ARk) position.

Turn the ignition knob to the LO ck position.
OVeRd RiVe (O/ d) Off SW iTc H
each time your vehicle is started, the cVT is automatically “reset” to Overdrive on.

To turn Overdrive mode off, push the O/D OFF switch
01 . The light in the instrument panel
will illuminate.

use the Overdrive off mode when you need improved engine braking.
01

10
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH (if so equipped)
The Vehicle dynamic control (Vdc) system uses various sensors to monitor driver inputs and
vehicle motion. under certain driving situations, the system will control braking and engine output to
help keep the vehicle on its steered path. V dc may need to be temporarily shut off if you are trying
to free a vehicle stuck in snow or mud.

Push the Vehicle dynamic control (VDC) OFF switch to deactivate the
Vdc system. The

light
will illuminate in the instrument panel gauge area.

Push the Vehicle dynamic control (VDC) OFF switch again to activate
the Vdc system. The

light in the instrument panel gauge area will

turn off.

The V dc system is active while the vehicle is running until the switch is
pressed to turn it off.
5-SPEED MANUAL TRANSMISSION (if so equipped)
To change gears, depress the clutch pedal fully and shift into the
appropriate gear, then release the clutch pedal slowly.

Start the vehicle in 1st gear and shift into 2nd, 3rd, 4th and 5th
gear according to the vehicle speed.

On the 5-speed manual transmission, you cannot shift directly
from 5th gear into R (ReVe RSe). Stop the vehicle completely,
move the shift lever into the n (neuTRAL) position, then move
into the R (ReVe RSe) position.
6-SPEED MANUAL TRANSMISSION (if so equipped)
LOck O uT
in 6-speed manual transmission equipped vehicles,
the shift lever is equipped with a Reverse lock-out
feature that prevents accidental selection of
Reverse (instead of 1st gear).
SHifTin G TO R eVeRSe
Lift up on the collar just below the shift knob, then
move the shift lever left and up into Reverse.