bulb NISSAN X-TRAIL 2003 Service Owner's Manual

TURN SIGNAL AND HAZARD WARNING LAMPS
LT-37
C
D
E
F
G
H
I
J
L
MA
B
LT

Trouble Diagnoses EKS003BG
Electrical Components InspectionEKS0034C
COMBINATION FLASHER UNIT CHECK

Before checking, ensure that bulbs meet specifications.

Connect a battery and test lamp to the combination flasher unit,
as shown. Combination flasher unit is properly functioning if it
blinks when power is supplied to the circuit.
Symptom Possible cause Repair order
Turn signal and hazard warning lamps do
not operate.1. Hazard switch
2. Combination flasher unit
3. Open in combination flasher unit circuit1. Check hazard switch.
2. Refer to combination flasher unit check.
3. Check wiring to combination flasher unit
for open circuit.
Turn signal lamps do not operate but haz-
ard warning lamps operate.1. 10A fuse
2. Hazard switch
3. Turn signal switch
4. Open in turn signal switch circuit1. Check 10A fuse [No. 2, located in fuse
block (J/B)]. Turn ignition switch ON and
verify battery positive voltage is present
at terminal 2 of hazard switch.
2. Check hazard switch.
3. Check turn signal switch.
4. Check the wire between combination
flasher unit terminal 3 and turn signal
switch terminal 1 for open circuit.
Hazard warning lamps do not operate but
turn signal lamps operate.1. 10A fuse
2. Hazard switch
3. Open in hazard switch circuit1. Check 10A fuse (No. 35, located in the
fuse and fusible link box). Verify battery
positive voltage is present at terminal 3
of hazard switch.
2. Check hazard switch.
3. Check the wire between combination
flasher unit terminal 3 and hazard switch
terminal 4 for open circuit.
Front turn signal lamp LH or RH does not
operate.1. Bulb
2. Grounds E24 and E501. Check bulb.
2. Check grounds E24 and E50.
Rear turn signal lamp LH or RH does not
operate.1. Bulb
2. Grounds B8 and B181. Check bulb.
2. Check grounds B8 and B18.
Side turn signal lamp LH or RH does not
operate.1. Bulb
2. Grounds E24 and E501. Check bulb.
2. Check grounds E24 and E50.
LH and RH turn indicators do not operate. 1. Ground 1. Check grounds M27 and M70.
LH or RH turn indicator does not operate. 1. Bulb 1. Check bulb in combination meter.
SEL122E

LT-38
TURN SIGNAL AND HAZARD WARNING LAMPS

Bulb ReplacementEKS0034D
FRONT TURN SIGNAL LAMP
1. Remove the front turn signal lamp. Refer toLT- 3 8 , "Removal and
Installation for Front Turn Signal Lamp"
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
SIDE TURN SIGNAL LAMP
1. Remove side turn signal lamp. Refer toLT- 3 8 , "Removal and
Installation for Side Turn Signal Lamp"
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
REAR TURN SIGNAL LAMP
Refer to LT- 6 3 , "Bulb Replacement" .
Removal and Installation for Front Turn Signal LampEKS003BH
REMOVAL
1. Press the upper pawl to remove front turn signal lamp toward
the front of the vehicle.
2. Disconnect front turn signal lamp connector.
INSTALLATION
1. Connect front turn signal lamp connector.
2. Insert the pawl into head lamp hole, and install front turn signal lamp.
Removal and Installation for Side Turn Signal LampEKS003BI
1. Push the side turn signal lamp toward A direction in the figure,
and pull up B direction in the figure.
2. Disconnect the side turn signal lamp connector.Front turn signal lamp : 12V 21W (amber)
SKIA0053E
Side turn signal lamp : 12V 5W
PKIA0468E
SKIA0054E
PKIA0469E

STOP LAMP
LT-43
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS0034K
STOP LAMP
Refer to LT- 6 3 , "Bulb Replacement" .
HIGH-MOUNTED STOP LAMP
1. Remove the high-mounted stop lamp cover. Refer to LT- 4 3 ,
"HIGH-MOUNTED STOP LAMP" .
2. Turn the high-mounted stop lamp bulb socket counterclockwise
and unlock it.
3. Remove the bulb.
Removal and InstallationEKS0034L
STOP LAMP
Refer toLT- 6 3 , "Removal and Installation" .
HIGH-MOUNTED STOP LAMP
1. Pull the edge of the cover (A in the figure below) to each side in
turn downward until the pawls inside the cover are released.
2. Pull down the cover toward under the vehicle.
3. Remove the high-mounted stop lamp mounting bolts.
4. Disconnect the high-mounted stop lamp connector and remove
it from the vehicle.High-mounted Stop Lamp : 12V 5W
PKIA0496E
PKIA8618E
PKIA5577E

LT-46
BACK-UP LAMP

Bulb Replacement EKS003C4
Refer to LT- 6 3 , "Bulb Replacement" .
Removal and Installation EKS003C5
Refer to LT- 6 3 , "Removal and Installation" .

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-51
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003C1
PARKING AND TAIL LAMPS
Refer to LT- 6 3 , "Bulb Replacement" .
LICENSE PLATE LAMP
1. Remove license plate lamp mounting screws (2).
2. Remove lens of license plate lamp.
3. Remove bulb from its socket.
4. Installation is the reverse of removal.
Removal and Installation EKS003C2
PARKING AND TAIL LAMPS
Refer to LT- 6 3 , "Removal and Installation" .
LICENSE PLATE LAMP
Removal
1. Remove the license lamp finisher. Refer to EI-31, "LICENSE
LAMP FINISHER" in “EXTERIOR & INTERIOR (EI)” section.
2. Remove the harness from installation pawl for harness.
3. Remove license plate lamp mounting screws (2 each, RH and
LH).
4. Pull out license plate lamp from license lamp finisher.
Installation

Install license plate lamp in the reverse order of removal, observing the tightening torque shown below.License plate lamp : 12V 5W
PKIA8753E
PKIA5760E
License plate lamp mounting screws
Tightening torque
: 1.4 N·m (0.15 kg-m, 13 in-lb)

FRONT FOG LAMP
LT-55
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003DI
1. Remove fog lamp. Refer to LT- 5 5 , "Removal and Installation" .
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
4. Install in the reverse order of removal.
CAUTION:

Do not touch the glass of bulb directly by hand. Keep
grease and other oily matters away from it. Do not touch
bulb by hand while it is lit or right after being turned off.
Burning may result.

Do not leave bulb out of fog lamp housing for a long time because dust, moisture smoke, etc. May
affect the performance of fog lamp. When replacing bulb, be sure to replace it with new one.
Removal and Installation EKS003DJ
REMOVAL
1. Remove fender protector. Refer to EI-21, "FENDER PROTECTOR" .
2. Disconnect fog lamp connector.
3. Remove fog lamp mounting nuts from fog lamp bracket.
4. Pull out fog lamp from vehicle and disconnect connector.
INSTALLATION

Install fog lamp in the reverse order of removal, observing the tightening torque shown below.Front fog lamp :12V 55W (H11)
PKIA5559E
PKIA5560E
Fog lamp mounting bolt
Tightening torque
: 5.5 N·m (0.56 kg-m, 49 in-lb)

REAR FOG LAMP
LT-59
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS0015L
1. Remove rear fog lamp. Refer to LT- 5 9 , "Removal and Installa-
tion" .
2. Turn bulb socket counterclockwise and unlock it.
3. Remove bulb.
Removal and InstallationEKS0015M
REMOVAL
1. Remove rear fog lamp mounting screws (2).
2. Take out rear fog lamp from bumper, then disconnect connector.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Rear fog lamp : 12V 21W
SKIA0052E
SKIA0090E
Rear fog lamp mounting screws
Tightening torque : 1.4 N·m (0.14 kg-m, 12 in-lb)

LT-60
CLEARANCE LAMP/TAIL LAMP

CLEARANCE LAMP/TAIL LAMPPFP:26010
Bulb Replacement (Clearance Lamp)EKS001UR
Refer to LT- 1 6 , "Bulb Replacement for Headlamp and Clearance lamp" .
Bulb Replacement (Tail lamp)EKS001US
Refer to LT- 6 3 , "Bulb Replacement" .
Removal and Installation of Clearance LampEKS001UT
Refer to LT- 1 7 , "Removal and Installation for Headlamp" .
Removal and Installation of Tail lampEKS001UU
Refer to LT- 6 3 , "Removal and Installation" .

HIGH-MOUNTED STOP LAMP
LT-61
C
D
E
F
G
H
I
J
L
MA
B
LT

HIGH-MOUNTED STOP LAMPPFP:26590
Bulb ReplacementEKS0034W
Refer to LT- 4 3 , "Bulb Replacement" .
Removal and InstallationEKS0034X
Refer to LT- 4 3 , "Removal and Installation" .

REAR COMBINATION LAMP
LT-63
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb ReplacementEKS00164
1. Remove rear combination lamp mounting bolts (2).
2. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb.
Removal and InstallationEKS00165
REMOVAL
1. Remove luggage-side lower finisher. Refer to EI-35, "BODY
SIDE TRIM" in "EI EXTERIOR & INTERIOR" section.
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts (2).
4. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
5. From outside the vehicle, pull harness grommet rearward, and
remove harness.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Stop/taillight : 12V 21/5W
Rear turn signal lamp : 12V 21W
Backup lamp : 12V 21W
SKIA0057E
PKIA8620E
Rear combination lamp mounting bolts
Tightening torque
: 5.4 N·m (0.55 kg-m, 48 in-lb)