turn signal bulb NISSAN X-TRAIL 2003 Service Repair Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2003, Model line: X-TRAIL, Model: NISSAN X-TRAIL 2003Pages: 4179, PDF Size: 87.27 MB
Page 4079 of 4179
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION
A
B
LT
LIGHTING SYSTEM
PRECAUTION ............................................................ 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
Precaution ................................................................ 3
Wiring Diagrams and Trouble Diagnosis .................. 3
HEADLAMP ................................................................ 4
System Description .................................................. 4
DESCRIPTION ...................................................... 4
LOW BEAM OPERATION ..................................... 4
HIGH BEAM OPERATION/FLASH-TO-PASS
OPERATION ......................................................... 4
DRIVING LAMP OPERATION .............................. 4
Schematic ................................................................ 6
Wiring Diagram — H/LAMP — ................................. 7
LHD MODELS ....................................................... 7
RHD MODELS .................................................... 10
Trouble Diagnoses ................................................. 13
Aiming Adjustment for Headlamp ........................... 14
LOW BEAM ......................................................... 14
Aiming Adjustment for Driving Lamp ...................... 15
PREPARATION BEFORE ADJUSTING .............. 15
ADJUSTMENT USING AN ADJUSTMENT
SCREEN (LIGHT/DARK BORDERLINE) ............ 16
ADJUSTING ........................................................ 16
Bulb Replacement for Headlamp and Clearance
lamp ....................................................................... 16
HEAD LAMP ....................................................... 16
CLEARANCE LAMP ........................................... 16
Bulb Replacement for Driving Lamp ...................... 17
Removal and Installation for Headlamp ................. 17
REMOVAL ........................................................... 17
INSTALLATION ................................................... 17
Removal and Installation for Driving Lamp ............ 18
REMOVAL ........................................................... 18
INSTALLATION ................................................... 18
Removal and Installation for Driving Lamp Switch ... 19
HEADLAMP - DAYTIME LIGHT SYSTEM - ............. 20
System Description ................................................ 20DESCRIPTION .................................................... 20
HEADLAMP OPERATION (DAYTIME LIGHT
CANCEL OPERATION) ....................................... 20
DAYTIME LIGHT OPERATION ........................... 20
DRIVING LAMP OPERATION ............................. 20
Schematic ............................................................... 22
Wiring Diagram -DTRL- .......................................... 23
Trouble Diagnoses ................................................. 28
DAYTIME LIGHT CONTROL UNIT INSPECTION
TABLE ................................................................. 28
Bulb Replacement .................................................. 28
Aiming Adjustment .................................................. 28
Removal and Installation ........................................ 28
HEADLAMP AIMING CONTROL ............................. 29
Wiring Diagram -H/AIM- ......................................... 29
Removal and Installation ........................................ 30
Switch Circuit Inspection ........................................ 30
TURN SIGNAL AND HAZARD WARNING LAMPS ... 31
System Description ................................................. 31
TURN SIGNAL OPERATION .............................. 31
HAZARD LAMP OPERATION ............................. 31
Wiring Diagram — TURN — ................................... 33
LHD MODELS ..................................................... 33
RHD MODELS .................................................... 35
Trouble Diagnoses ................................................. 37
Electrical Components Inspection .......................... 37
COMBINATION FLASHER UNIT CHECK ........... 37
Bulb Replacement .................................................. 38
FRONT TURN SIGNAL LAMP ............................ 38
SIDE TURN SIGNAL LAMP ................................ 38
REAR TURN SIGNAL LAMP .............................. 38
Removal and Installation for Front Turn Signal Lamp ... 38
REMOVAL ........................................................... 38
INSTALLATION ................................................... 38
Removal and Installation for Side Turn Signal Lamp ... 38
Removal and Installation for Rear Turn Signal Lamp ... 39
LIGHTING AND TURN SIGNAL SWITCH ................ 40
Removal and Installation ........................................ 40
Switch Circuit Inspection ........................................ 40
Page 4095 of 4179
HEADLAMP
LT-17
C
D
E
F
G
H
I
J
L
MA
B
LT
CAUTION:
Do not touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
When replacing bulb, prepare new bulb first of all. Do not leave bulb out of headlamp housing for
a long period, because dust, moisture or smoke will cause performance lowering (fouling, cloud,
etc.) of headlamp reflector and lens.
When bulb is installed, be sure to lock rubber cap to ensure watertightness.
Bulb Replacement for Driving LampEKS00AP9
1. Remove the driving lamp. Refer to LT- 1 8 , "Removal and Installa-
tion for Driving Lamp" in “HEADLAMP”.
2. Disconnect driving lamp connector.
3. Turn bulb socket counterclockwise and unlock it.
4. Install in the reverse order of removal.
CAUTION:
Do not touch the glass of bulb directly by hand. Keep
grease and other oily matters away from it. Do not touch
bulb by hand while it is lit or right after being turned off.
Burning may result.
When replacing bulb, prepare new bulb first of all. Do not leave bulb out of driving lamp housing
for a long period, because dust, moisture or smoke will cause performance lowering (fouling,
cloud, etc.) of driving lamp reflector and lens.
Removal and Installation for HeadlampEKS003CI
REMOVAL
1. Remove the front turn signal lamps. Refer toLT- 3 8 , "Removal
and Installation for Front Turn Signal Lamp" .
2. Disconnect connector of headlamp and clearance lamp.
3. Remove the front grille. Refer to EI-19, "
FRONT GRILLE" in
"EXTERIOR & INTERIOR (EI)" section.
4. Remove the headlamp mounting bolts.
5. Pull the headlamp toward the front of the vehicle.
INSTALLATION
Install in the reverse order of removal, taking care of the following points.
Headlamp mounting boltsClearance lamp : 12V 5W
Driving lamp : 12 V - 65 W (H1R1 halogen)
PKIA3396E
PKIA5555E
Headlamp mounting bolts
Tightening torque
: 5.5 N·m (0.55 kg-m, 48 in-lb)
Page 4115 of 4179
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-37
C
D
E
F
G
H
I
J
L
MA
B
LT
Trouble Diagnoses EKS003BG
Electrical Components InspectionEKS0034C
COMBINATION FLASHER UNIT CHECK
Before checking, ensure that bulbs meet specifications.
Connect a battery and test lamp to the combination flasher unit,
as shown. Combination flasher unit is properly functioning if it
blinks when power is supplied to the circuit.
Symptom Possible cause Repair order
Turn signal and hazard warning lamps do
not operate.1. Hazard switch
2. Combination flasher unit
3. Open in combination flasher unit circuit1. Check hazard switch.
2. Refer to combination flasher unit check.
3. Check wiring to combination flasher unit
for open circuit.
Turn signal lamps do not operate but haz-
ard warning lamps operate.1. 10A fuse
2. Hazard switch
3. Turn signal switch
4. Open in turn signal switch circuit1. Check 10A fuse [No. 2, located in fuse
block (J/B)]. Turn ignition switch ON and
verify battery positive voltage is present
at terminal 2 of hazard switch.
2. Check hazard switch.
3. Check turn signal switch.
4. Check the wire between combination
flasher unit terminal 3 and turn signal
switch terminal 1 for open circuit.
Hazard warning lamps do not operate but
turn signal lamps operate.1. 10A fuse
2. Hazard switch
3. Open in hazard switch circuit1. Check 10A fuse (No. 35, located in the
fuse and fusible link box). Verify battery
positive voltage is present at terminal 3
of hazard switch.
2. Check hazard switch.
3. Check the wire between combination
flasher unit terminal 3 and hazard switch
terminal 4 for open circuit.
Front turn signal lamp LH or RH does not
operate.1. Bulb
2. Grounds E24 and E501. Check bulb.
2. Check grounds E24 and E50.
Rear turn signal lamp LH or RH does not
operate.1. Bulb
2. Grounds B8 and B181. Check bulb.
2. Check grounds B8 and B18.
Side turn signal lamp LH or RH does not
operate.1. Bulb
2. Grounds E24 and E501. Check bulb.
2. Check grounds E24 and E50.
LH and RH turn indicators do not operate. 1. Ground 1. Check grounds M27 and M70.
LH or RH turn indicator does not operate. 1. Bulb 1. Check bulb in combination meter.
SEL122E
Page 4116 of 4179
LT-38
TURN SIGNAL AND HAZARD WARNING LAMPS
Bulb ReplacementEKS0034D
FRONT TURN SIGNAL LAMP
1. Remove the front turn signal lamp. Refer toLT- 3 8 , "Removal and
Installation for Front Turn Signal Lamp"
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
SIDE TURN SIGNAL LAMP
1. Remove side turn signal lamp. Refer toLT- 3 8 , "Removal and
Installation for Side Turn Signal Lamp"
2. Turn the bulb socket counterclockwise and unlock it.
3. Remove the bulb from its socket.
REAR TURN SIGNAL LAMP
Refer to LT- 6 3 , "Bulb Replacement" .
Removal and Installation for Front Turn Signal LampEKS003BH
REMOVAL
1. Press the upper pawl to remove front turn signal lamp toward
the front of the vehicle.
2. Disconnect front turn signal lamp connector.
INSTALLATION
1. Connect front turn signal lamp connector.
2. Insert the pawl into head lamp hole, and install front turn signal lamp.
Removal and Installation for Side Turn Signal LampEKS003BI
1. Push the side turn signal lamp toward A direction in the figure,
and pull up B direction in the figure.
2. Disconnect the side turn signal lamp connector.Front turn signal lamp : 12V 21W (amber)
SKIA0053E
Side turn signal lamp : 12V 5W
PKIA0468E
SKIA0054E
PKIA0469E
Page 4141 of 4179
REAR COMBINATION LAMP
LT-63
C
D
E
F
G
H
I
J
L
MA
B
LT
Bulb ReplacementEKS00164
1. Remove rear combination lamp mounting bolts (2).
2. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
3. Turn bulb socket counterclockwise and unlock it.
4. Remove bulb.
Removal and InstallationEKS00165
REMOVAL
1. Remove luggage-side lower finisher. Refer to EI-35, "BODY
SIDE TRIM" in "EI EXTERIOR & INTERIOR" section.
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts (2).
4. Pull rear combination lamp toward rear of vehicle. Disengage
locating pins (3).
5. From outside the vehicle, pull harness grommet rearward, and
remove harness.
INSTALLATION
Install in the reverse order of removal, paying attention to the following.Stop/taillight : 12V 21/5W
Rear turn signal lamp : 12V 21W
Backup lamp : 12V 21W
SKIA0057E
PKIA8620E
Rear combination lamp mounting bolts
Tightening torque
: 5.4 N·m (0.55 kg-m, 48 in-lb)
Page 4170 of 4179
LT-92
BULB SPECIFICATIONS
BULB SPECIFICATIONSPFP:26297
HeadlampEKS003GS
Exterior LampEKS003GT
Interior Lamp/IlluminationEKS003GU
Item Wattage (W)
Low/High55 /60(H4)
Driving lamp65(H1R1)
Item Wattage (W)
Front combination lamp Clearance lamp 5
Front turn signal lamp21(amber)
Side turn signal lamp5
Fog lampFront fog lamp 55(H11)
Rear fog lamp 21
Rear combination lampStop/Tail lamp 21/5
Turn signal lamp 21
Back-up lamp 21
License plate lamp5
High-mounted stop lamp5
Item Wattage (W)
Ashtray illumination1.4
Interior room lamp10
Spot lampWithout sunroof 8
With sunroof 10
Luggage room lamp10