ABS NISSAN X-TRAIL 2005 Service Repair Manual

CAN SYSTEM (TYPE 9)
LAN-169
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN

2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect steering angle sensor connector.
2. Check resistance between steering angle sensor harness con-
nector M81 terminals 4 (W) and 5 (R).
OK or NG
OK >> Replace steering angle sensor.
NG >> Repair harness between steering angle sensor and har-
ness connector M75.
Combination Meter Circuit InspectionEKS00NLH
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check terminals and connector of combination meter for damage, bend and loose connection (meter side
and harness side).
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.
2. CHECK HARNESS FOR OPEN CIRCUIT
1. Disconnect combination meter connector.
2. Check resistance between combination meter harness connec-
tor M44 terminals 22 (W) and 23 (R).
OK or NG
OK >> Replace combination meter.
NG >> Repair harness between combination meter and steer-
ing angle sensor.
CAN Communication Circuit InspectionEKS00NLI
1. CHECK CONNECTOR
1. Turn ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check following terminals and connectors for damage, bend and loose connection (control module side,
control unit side, sensor side, meter side, connector side and harness side).
–ECM
–ESP/TCS/ABS control unit
–Steering angle sensor
–Combination meter
–Between ECM and combination meter
OK or NG
OK >> GO TO 2.
NG >> Repair terminal or connector.4 (W) - 5 (R) : Approx. 54 - 66 Ω
SKIA6870E
22 (W) - 23 (R) : Approx. 108 - 132 Ω
SKIA9780E

LAN-170
[CAN]
CAN SYSTEM (TYPE 9)

2. CHECK HARNESS FOR SHORT CIRCUIT
1. Disconnect ECM connector and harness connector M75.
2. Check continuity between ECM harness connector M118 termi-
nals 95 (G/R) and 87 (GY/R).
OK or NG
OK >> GO TO 3.
NG >> Repair harness between ECM and harness connector
M75.
3. CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between ECM harness connector M118 terminals
95 (G/R), 87 (GY/R) and ground.
OK or NG
OK >> GO TO 4.
NG >> Repair harness between ECM and harness connector
M75.
4. CHECK HARNESS FOR SHORT CIRCUIT
1. Disconnect ESP/TCS/ABS control unit connector.
2. Check continuity between ESP/TCS/ABS control unit harness
connector E122 terminals 61 (W) and 63 (R).
OK or NG
OK >> GO TO 5.
NG >> Repair harness between ESP/TCS/ABS control unit and
harness connector E116.
5. CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between ESP/TCS/ABS control unit harness con-
nector E122 terminals 61 (W), 63 (R) and ground.
OK or NG
OK >> GO TO 6.
NG >> Repair harness between ESP/TCS/ABS control unit and
harness connector E116. 95 (G/R) - 87 (GY/R) : Continuity should not exist.
SKIB0120E
95 (G/R) - Ground : Continuity should not exist.
87 (GY/R) - Ground : Continuity should not exist.
SKIB0121E
61 (W) - 63 (R) : Continuity should not exist.
PKIA9632E
61 (W) - Ground : Continuity should not exist.
63 (R) - Ground : Continuity should not exist.
PKIA9633E

HARNESS
PG-65
C
D
E
F
G
H
I
J
L
MA
B
PG

Wiring Diagram Codes (Cell Codes) EKS0032J
Use the chart below to find out what each wiring diagram code stands for.
Refer to the wiring diagram code in the alphabetical index to find the location (page number) of each wiring
diagram.
Code Section Wiring Diagram Name
1STSIG AT A/T 1st Signal
2NDSIG AT A/T 2nd Signal
3RDSIG AT A/T 3rd Signal
4THSIG AT A/T 4th Signal
4WD TF 4WD Control system
A/C ATC Air Conditioner
ABS BRC Anti-Lock Brake System
APP1PW EC Accelerator Pedal Position Sensor 1 Power Supply
APP2PW EC Accelerator Pedal Position Sensor 2 Power Supply
APPS1 EC Accelerator Pedal Position Sensor
APPS2 EC Accelerator Pedal Position Sensor
APPS3 EC Accelerator Pedal Position Sensor
ASC/BS EC Automatic Speed Control Device (ASCD) Brake Switch
ASC/SW EC Automatic Speed Control Device (ASCD) Steering Switch
ASCBOF EC Automatic Speed Control Device (ASCD) Brake Switch
ASCIND EC Automatic Speed Control Device (ASCD) Indicator
AT/IND DI A/T Indicator Lamp
AUDIO AV Audio
BA/FTS AT A/T Fluid Temperature Sensor and TCM Power Supply
BACK/L LT Back-Up Lamp
BOOST EC Turbocharger Boost Sensor
BRK/SW EC Brake Switch
CAN AT CAN Communication Line
CAN EC CAN Communication Line
CAN LAN CAN System
CHARGE SC Charging System
CHIME DI Warning Chime
CIGAR WW Cigarette Lighter
CKPS EC Crankshaft Position Sensor
CLOCK DI Clock
CMPS EC Camshaft Position Sensor
COOL/F EC Cooling Fan Control
D/LOCK BL Power Door Lock
DEF GW Rear Window Defogger
DTRL LT Headlamp - With Daytime Light System
ECM/PW EC ECM Power Supply for Back-Up
ECMRLY EC ECM Relay
ECTS EC Engine Coolant Temperature Sensor
EGRVLV EC EGR Volume Control Valve
EGVC/V EC EGR Volume Control Valve
ENGSS AT Engine Speed Signal

PG-66
HARNESS

ESP BRC ESP/TCS/ABS Control System
ETC1 EC Electric Throttle Control Function
ETC2 EC Electric Throttle Control Motor Relay
ETC3 EC Electric Throttle Control Motor
F/FOG LT Front Fog Lamp
F/PUMP EC Fuel Pump
FIAR EC Fuel Injector Adjustment Resistor
FRO2 EC Front Heated Oxygen Sensor
FRO2/H EC Front Heated Oxygen Sensor Heater
FRPS EC Fuel Rail Pressure Sensor
FTP EC Fuel Transport Pump
FTS AT A/T Fluid Temperature Sensor Circuit
FTS EC Fuel Temperature Sensor
FUEL EC Fuel Injection System Function
GLORLY EC Glow Relay
GLOW EC Glow Control System
H/AIM LT Headlamp Aiming Control System
H/LAMP LT Headlamp
HEATER MTC Heater System
HLC WW Headlamp Cleaner
HO2S1 EC Heated Oxygen Sensor 1
HO2S1H EC Heated Oxygen Sensor 1 Heater
HO2S2 EC Heated Oxygen Sensor 2
HO2S2H EC Heated Oxygen Sensor 2 Heater
HORN WW Horn
HSEAT SE Heated Seat
IATS EC Intake Air Temperature Sensor
IATSEN EC Intake Air Temperature Sensor
IGNSYS EC Ignition System
ILL LT Illumination
INJ/PW EC Fuel Injector Power Supply Circuit
INJECT EC Fuel Injector
INT/L LT Map Lamp
IVC EC Intake Valve Timing Control Solenoid Valve
KS EC Knock Sensor
LOAD EC Electrical Load Signal
LPSV AT Line Pressure Solenoid Valve
MAFS EC Mass Air Flow Sensor
MAIN AT Main Power Supply and Ground Circuit
MAIN EC Main Power Supply and Ground Circuit
METER DI Speedometer, Tachometer, Temp. and Fuel Gauges
MIL/DL EC MIL & Data Link Connector
MIRROR GW Door Mirror
MULTI BL Multi-Remote Control SystemCode Section Wiring Diagram Name

ENGINE MAINTENANCE (QR20DE·QR25DE)
MA-25
C
D
E
F
G
H
I
J
K
MA
B
MA

CAUTION:

The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.

Always use oil level gauge to determine the proper amount of engine oil in the engine.
7. Warm up engine and check area around drain plug and oil filter for oil leakage.
8. Stop engine and wait for 10 minutes.
9. Check the engine oil level.
Changing Oil FilterELS000ZJ
REMOVAL
1. Open oil filter installation/removal cover on RH undercover.
2. Using an oil filter wrench (special service tool), remove oil filter.
CAUTION:

Oil filter is provided with relief valve. Use Genuine Nissan
Oil Filter or equivalent.

Be careful not to get burned when engine and engine oil
may be hot.

When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.

Do not allow engine oil to adhere to drive belt.

Completely wipe off any engine oil that adheres to engine
and vehicle.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
PBIC0249E
KBIA0303E
SMA010

MA-36
ENGINE MAINTENANCE (YD22DDTI)

CAUTION:

The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.

Always use the dipstick to the determine when the proper amount of engine oil is in the engine.
7. Warm up engine and check area around drain plug and oil filter for oil leakage.
8. Stop engine and wait for 10 minutes.
9. Check the engine oil level.
Changing Oil Filter (TYPE A)ELS000CI
REMOVAL
1. Open oil filter installation/ removal cover on RH engine undercover.
2. Using the oil filter wrench, remove the oil filter.
CAUTION:

Be careful not to get burned when the engine and engine oil are hot.

When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.

Do not allow engine oil to adhere to the drive belts.

Completely wipe off any engine oil that adhere to the engine and the vehicle.

The oil filter is provided with a relief valve.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply engine oil to the oil seal circumference of the new oil filter.
3. Screw the oil filter manually until it touches the installation surface, then tighten it by 1/2 turn. Or tighten to
specification.
INSPECTION AFTER INSTALLATION
1. Start engine, and check there is no leak of engine oil.
2. Stop engine and wait for 10 minutes.
3. Check the engine oil level and add engine oil. Refer to MA-35, "
Changing Engine Oil" .
PBIC0249E
SMA010
Oil filter:
: 18 N·m (1.8 Kg-m, 13 ft-lb)

ENGINE MAINTENANCE (YD22DDTI)
MA-37
C
D
E
F
G
H
I
J
K
MA
B
MA

Changing Oil Filter (TYPE B)ELS000ZM
REMOVAL
CAUTION:

Be careful not to get burned when engine and engine oil are
hot.

When removing, prepare a shop cloth to absorb any engine
oil leakage or spillage.

Do not allow engine oil to adhere to drive belts.

Completely wipe off any engine oil that adhere to engine
and vehicle.
1. Open oil filter installation/removal cover on RH engine undercover.
2. Using a socket wrench [plane-to-plane width: 17 mm (0.67 in)],
loosen oil filter body approximately four turns.
3. Drain engine oil after matching the "DRAIN" arrow mark at the
bottom of oil filter body to the protrusion on oil filter bracket.

Catch engine oil with a pan or cloth.
CAUTION:

The drained engine oil flows over the right surface of
oil filter body.

Completely wipe clean any engine oil remaining on oil
filter body or vehicle.
4. Remove oil filter body, then remove oil filter.
PBIC2536E
JLC290B
JLC291B

MA-46
CHASSIS AND BODY MAINTENANCE


Check lines for improper attachment, leaks, cracks, dam-
age, loose connections, chafing and deterioration.

Check rack boots for accumulation of power steering fluid.
Axle and Suspension PartsELS000BQ
Check front and rear axle and suspension parts for excessive play,
cracks, wear or other damage.

Shake each wheel to check for excessive play.

Check wheel bearings for smooth operation.

Check axle and suspension nuts and bolts for looseness.

Check strut (shock absorber) for oil leakage or other damage.

Check suspension ball joint for grease leakage and ball joint
dust cover for cracks or other damage.
Drive ShaftELS000CL

Check boot and drive shaft for cracks, wear, damage and
grease leakage.
Lubricating Locks, Hinges and Hood LatchesELS000BR
SST851C
SMA525A
SFA392B
SFA108A
Front door Refer to BL-18, "DOOR" .
Back door Refer to BL-99, "
BACK DOOR" .

IDX-8
ALPHABETICAL INDEX
Spark plug(QR20DE-QR25DE) ........................ EM-32
Specification value ............................. EC-120, EC-620
Speedometer ........................................................ DI-4
Spiral cable ..................................................... SRS-33
SROOF - Wiring diagram ................................... RF-11
SRS - See Supplemental Restraint System ..... SRS-6
SRS - Wiring diagram/LHD ............................. SRS-11
SRS - Wiring diagram/RHD ............................ SRS-13
SRS Trouble diagnoses .................................... SRS-8
Stall test (A/T) ...................................... AT-65, AT-257
Standardized relay ............................................. PG-77
START - Wiring diagram ........................ SC-24, SC-25
Start signal ..................................... EC-1345, EC-1696
Starter ................................................................ SC-23
Starting system .................................................. SC-23
Steering gear and linkage inspection ................ MA-45
Steering knuckle ................................................ FAX-7
Steering linkage ................................................. PS-16
Steering wheel and column ..................... PS-8, PS-11
Steering wheel turning force ................................ PS-8
Stop lamp .............................................. LT-98, LT-118
Stop lamp switch ................................ EC-405, EC-809
STOP/L - Wiring diagram ...................... LT-98, LT-118
Suction control valve .... EC-1231, EC-1275, EC-1280,
EC-1570
, EC-1614, EC-1619
Sunload sensor ............. ATC-114, ATC-116, ATC-123
Sunroof .............................................................. RF-10
Super lock .......................................................... BL-42
Supplemental Restraint System ....................... SRS-6
Supplemental restraint system - Wiring diagram/LHD ..
SRS-11
Supplemental restraint system - Wiring diagram/RHD .
SRS-13
Suspension ....................................................... MA-46
Symbols and abbreviations ........................ GI-9, GI-22
Symptom matrix chart .......................... EC-84, EC-584
Synchronizer (M/T) ............................... MT-23, MT-41
System readiness test (SRT) code .................... EC-56
T
Tachometer ........................................................... DI-4
Tail lamp ............................................. LT-103, LT-116
TAIL/L - Wiring diagram ...................... LT-103, LT-145
Tailgate lamp .................................................... LT-103
TC boost control solnoid valve ...... EC-1061, EC-1506,
EC-1659
TC boost sensor ............................................ EC-1151
TCC/V - Wiring diagram ................. EC-1062, EC-1660
TCM circuit diagram ........................................... AT-21
TCM inspection table ........................... AT-94, AT-286
THEFT - Wiring diagram .................................. BL-104
Thermal protector ............................................ ATC-95
Thermostat(QR20DE-QR25DE) ....................... CO-23
Thermostat(YD22DDTi) .................................... CO-46
Three way catalyst function ............................. EC-264
Three way catalyst precautions ............................ GI-5
Three way catalyst(QR20DE-QR25DE) ........... EM-25
Throttle control motor relay ................ EC-306, EC-737
Throttle position sensor (TPS) ......... EC-171, EC-231,
EC-368
, EC-370, EC-424, EC-658, EC-680, EC-771,
EC-773
, EC-830
Throwout bearing - See Clutch release bearing CL-14
Time control system .......................................... BCS-3
Timing chain(QR20DE-QR25DE) ..................... EM-46
Timing chain(YD22DDTi) .................. EM-193, EM-198
Torque converter installation ............. AT-415, AT-523
TPS1 - Wiring diagram ..................... EC-233, EC-682
TPS2 - Wiring diagram ..................... EC-173, EC-660
TPS3 - Wiring diagram ..................... EC-426, EC-832
Transmission case (M/T) ...................... MT-22, MT-40
Trouble diagnoses .............................................. GI-10
Turbocharger charge air cooler(YD22DDTi) ... EM-144
Turbocharger precautions ..................................... GI-6
Turbocharger(YD22DDTi) ............................... EM-151
TURN - Wiring diagram .......................... LT-87, LT-89
Turn signal lamp ................................... LT-87, LT-118
Two trip detection logic ....................... EC-52, EC-565
V
Vacuum hose (brake system) ............................ BR-25
Vacuum hose drawing (Engine control) EC-32, EC-545
Vacuum pump(YD22DDTi) ............................. EM-163
Valve clearance(QR20DE-QR25DE) ................ EM-64
Valve clearance(YD22DDTi) ........................... EM-185
Valve guide ....................................................... EM-77
Valve guide(QR20DE-QR25DE) ....................... EM-77
Valve lifter(QR20DE-QR25DE) ......................... EM-56
Valve lifter(YD22DDTi) ................................... EM-183
Valve seat(QR20DE-QR25DE) ......................... EM-79
Valve seat(YD22DDTi) ................................... EM-219
Valve spring(QR20DE-QR25DE) ...................... EM-80
Variable induction air control system (VIAS) ... EC-457,
EC-897
Vehicle speed sensor (VSS) EC-276, EC-403, EC-709,
EC-807
VIAS - Wiring diagram ...................... EC-459, EC-899
W
WARN - Wiring diagram .......................... DI-36
, DI-44
Warning chime .................................................... DI-56
Warning lamps .................................................... DI-35
Washer, front ..................................................... WW-4
Washer, rear .................................................... WW-14
Water control valve(QR20DE-QR25DE) ........... CO-23
Water pump(QR20DE-QR25DE) ...................... CO-21
Water pump(YD22DDTi) ................................... CO-43
Water temperature gauge ..................................... DI-4
Weatherstrip - See Exterior ............................... BL-21
Wheel alignment (front) .................................... FSU-6
Wheel alignment (rear) ..................................... RSU-6
Wheel balance ....................................... WT-4, MA-43
Wheel bearing (rear) ........................... RAX-6, RAX-10
Wheel hub (front) ............................................... FAX-7
Wheel hub (rear) ............................................. RAX-10
Wheel sensors (ABS) ..................................... BRC-46