lt-10 NISSAN X-TRAIL 2005 Service Repair Manual

LT-10
HEADLAMP - XENON TYPE -

T K W B 111 7 E

LT-100
BACK-UP LAMP

BACK-UP LAMPPFP:26550
Wiring Diagram — BACK/L — EKS003C3
GASOLINE ENGINE
TKWA1530E

BACK-UP LAMP
LT-101
C
D
E
F
G
H
I
J
L
MA
B
LT

DIESEL ENGINE
TKWA1531E

LT-102
BACK-UP LAMP

Bulb Replacement EKS003C4
Refer to LT- 11 9 , "Bulb Replacement" in “REAR COMBINATION LAMP”.
Removal and Installation EKS003C5
Refer to LT- 11 9 , "Removal and Installation" in “REAR COMBINATION LAMP”.

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-103
C
D
E
F
G
H
I
J
L
MA
B
LT

PARKING, LICENSE PLATE AND TAIL LAMPSPFP:26550
Wiring Diagram — TAIL/L — EKS003C0
LHD MODELS
TKWA1532E

LT-104
PARKING, LICENSE PLATE AND TAIL LAMPS

TKWA0066E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-105
C
D
E
F
G
H
I
J
L
MA
B
LT

RHD MODELS
TKWA1533E

LT-106
PARKING, LICENSE PLATE AND TAIL LAMPS

TKWA1534E

PARKING, LICENSE PLATE AND TAIL LAMPS
LT-107
C
D
E
F
G
H
I
J
L
MA
B
LT

Bulb Replacement EKS003C1
PARKING AND TAIL LAMPS
Refer to LT- 3 7 , "Bulb Replacement of Headlamp and Clearance lamp" in “HEADLAMP -CONVENTIONAL
TYPE-” or LT- 2 0 , "
Bulb Replacement of Headlamp and Clearance Lamp" in “HEADLAMP -XENON TYPE-”.
TAIL LAMP
Refer to LT- 11 9 , "Bulb Replacement" in “REAR COMBINATION LAMP”.
LICENSE PLATE LAMP
1. Remove license plate lamp mounting screws.
2. Remove lens of license plate lamp.
3. Remove bulb from its socket.
4. Installation is the reverse order of removal.
Removal and Installation EKS003C2
PARKING LAMP
Refer to LT- 3 8 , "Removal and Installation of Headlamp" in “HEADLAMP -CONVENTIONAL TYPE-” or LT- 2 1 ,
"Removal and Installation of Headlamp" in “HEADLAMP -XENON TYPE-”.
TAIL LAMP
Refer to LT- 11 9 , "Removal and Installation" in “REAR COMBINATION LAMP”.
LICENSE PLATE LAMP
Removal
1. Remove the license lamp finisher. Refer to EI-31, "LICENSE
LAMP FINISHER" in “EXTERIOR & INTERIOR (EI)” section.
2. Remove the harness from installation pawl for harness.
3. Remove license plate lamp mounting screws (2 each, RH and
LH).
4. Pull out license plate lamp from license lamp finisher.
Installation
Installation is the reverse order of removal.License plate lamp : 12V - 5W
PKIA8753E
PKIA5760E
License plate lamp mounting screws
: 1.4 N·m (0.15 kg-m, 13 in-lb)

LT-108
FRONT FOG LAMP

FRONT FOG LAMP PFP:00011
System Description EKS003DF
DESCRIPTION
Power is supplied at all times

through 10A fuse (No. 31, located in fuse and fusible link box)

to lighting switch terminal 11,

through 15A fuse (No. 42, located in fuse and fusible link box)

to front fog lamp relay terminal 3.
With the lighting switch in the 2ND position, power is supplied

through lighting switch terminal 12

to fog lamp switch terminal 32.
FOG LAMP OPERATION
The fog lamp switch is built into the combination switch. The lighting switch must be in the 1ST or 2ND position
for front fog lamp operation.
With the fog lamp switch in the FRONT FOG ON position or FRONT & REAR FOG ON position, power is sup-
plied

through fog lamp switch terminal 31

to front fog lamp relay terminal 2.
Ground is supplied

to front fog lamp relay terminal 1

through grounds E24 and E50.
The front fog lamp relay is energized and power is supplied

through front fog lamp relay terminal 5

to front fog lamp LH and RH terminal 1, and

to combination meter terminal 15.
Ground is supplied

to front fog lamp LH and RH terminal 2

through grounds E24 and E50,

to combination meter terminal 64

through grounds M27 and M70.
With power and ground supplied, the front fog lamps and FRONT FOG indicator illuminate.