start NISSAN X-TRAIL 2020 Owners Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2020, Model line: X-TRAIL, Model: NISSAN X-TRAIL 2020Pages: 400, PDF Size: 8.75 MB
Page 315 of 400
> ( G L W 0 R G H O 7 $ @
T32A1308 27-B5BB810 9-3587-4C7A-979E-9F8A81D60F87
When leaving yourvehicle unoccupied:
. Always takethekey with you-even when leaving
the vehicle inyour owngarage.
. Close allwindows completely andlock alldoors.
. Always parkyourvehicle whereitcan beseen.
Park inawell litarea during thenight.
. Ifthe security systemisequipped, useit-even for
a short period.
. Never leavechildren orpets inthe vehicle
unattended.
. Never leavevaluables insidethevehicle. Always
take valuables withyou.
. Never leavethevehicle documents inthe vehicle.
. Never leavearticles onaroof rack. Remove them
from therack andkeep andlock them inside the
vehicle.
. Never leavethespare keyinthe vehicle.
T32A130 827-31F5E2 3F-87C8-4D EE-9E65-020 C019B2AB5
WARNING:
. Whatever thecondition, drivewithcaution.
Accelerate anddecelerate withgreat care.If
accelerating ordecelerating toofast, the
drive wheels willlose even more traction.
. Allow morestopping distanceincold weath-
er driving. Braking shouldbestarted sooner
than ondry pavement.
. Keep atagreater distance fromthevehicle
in front ofyou onslippery roads.
. Wet ice(08C ,328F andfreezing rain),very
cold snow andicecan beslick andvery
difficult todrive on.The vehicle willhave a
lot less traction orgrip under thesecondi-
tions. Try to avoid driving onwet iceuntil the
road issalted orsanded.
. Watch forslippery spots(glaring ice).These
may appear onanotherwise clearroadin
shaded areas.Ifapatch ofice isseen ahead,
brake before reaching it.Try not tobrake
while actually onthe ice, and avoid any
sudden steering maneuvers.
. Donot use cruise control onslippery roads.
. Snow cantrap dangerous exhaustgasunder
your vehicle. Keepsnow clearofthe exhaust
pipe andfrom around yourvehicle.
BA TTER Y
T32A1308 27-BD622 040-1F8F-4 FB6-8DF8-8 96F8AF3E92 5
If the battery isnot fully charged duringextremely cold
weather conditions, thebattery fluidmayfreeze and
damage thebattery .To maintain maximum efficiency,
the battery shouldbechecked regularly.For details,
see ªBatteryº (P.8-20) ofthis manual.
ENGINE COOLANT
T32A1308 27-1902E3 10-78AC-4591-9565-1 9BAB071E173
If the vehicle isto be left outside withoutanti-freeze,
drain thecooling system, including theengine block.
Refill before operating thevehicle. Fordetails, see
ªChanging enginecoolantº (P.8-9) ofthis manual.
TIRE EQUIPMENT
T32A130 827-77A3E3 81-71B6-489C -8E41-9907068B0B92
1. Ifyou have snow tiresinstalled onthe front/rear
wheels ofyour vehicle, theyshould beofthe same
size, loading range,construction andtype (bias,
bias-belted orradial) asthe rear/front tires.
2. Ifthe vehicle isto be operated insevere winter
conditions, snowtiresshould beinstalled onall
four wheels.
3. Foradditional tractiononicy roads, studded tires
may beused. However, somecountries, provinces
and states prohibit theiruse.Check local,state
and provincial lawsbefore installing studdedtires.
Skid andtraction capabilities ofstudded
snow tires,onwet ordry surfaces, maybe
poorer thanthatofnon-studded snowtires.
4. Snow chains maybeused ifdesired. Makesure
they arethe proper sizeforthe tires onyour
vehicle andareinstalled according tothe chain
manufacturer's instructions.Usechain tensioners
when recommended bythe tire chain manufac-
turer toensure atight fit.Loose endlinks ofthe tire
chains mustbesecured orremoved toprevent the
possibility ofwhipping actiondamage tothe
Starting anddriving
5-59
VEHICLE
SECURITY COLDWEATHER DRIVING
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 316 of 400
> ( G L W 0 R G H O 7 $ @
5-60
Starting anddriving
fenders orunderbody .In addition, driveata
reduced speed,otherwise, yourvehicle maybe
damaged and/orvehicle handling andperfor-
mance maybeadversely affected.
SPECIAL WINTEREQUIPMENT
T32A130827-3 8F91172-3BF7-430D-9536-3CE83 B06974C
It is recommended thatthefollowing itemsbecarried
in the vehicle duringthewinter:
. Ascraper andstiff-bristled brushtoremove ice
and snow fromthewindows.
. Asturdy ,flat board tobe placed underthejack to
give itfirm support.
. Ashovel todig thevehicle outofsnowdrifts.
P ARKING BRAKE
GUID-ED1 242F6-0D74 -4A0A-8880-253E42ECF 77A
When parking inan area where theoutside tempera-
ture isbelow 08C (32 8F),do not apply theparking
brake toprevent itfrom freezing. Forsafe parking:
. Place theshift lever inthe ªPº (Park) position (CVT
model) .
. Place theshift lever inthe ª1º(1st) orªRº
(Reverse) gear(MTmodel) .
. Securely blockthewheels.
For models equipped withelectronic parking
brake system
GUID-029 E85CF-75D 0-448C-A695-99F6A6377 9EC
T o keep theelectronic parkingbrakereleased afterthe
engine isturned off,see ªParking brakeº(P.3-30) .
CORROSION PROTECTION
T32A130827-3 F1FCB4A-7D59-4318 -9831-CEC 3E4022DD1
Chemicals usedforroad surface deicingareextremely
corrosive andwillaccelerate corrosionandthe
deterioration ofunderbody components suchasthe
exhaust system,fueland brake lines,brake cables,
floor panandfenders.
In the winter, theunderbody mustbecleaned
periodically. Foradditional information, see
ªCorrosion protectionº (P.7-5) ofthis manual.
For additional protection againstrustandcorrosion,
which mayberequired insome areas, consult a
NISSAN dealer.
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 317 of 400
> ( G L W 0 R G H O 7 $ @
6 In case ofemergency
Hazard indicator flasherswitch ....
........................................................... .6-2
Flat tire....
........................................................... ............................................6-2
Tire Pressure Monitoring System(TPMS) (ifequipped) ....
........ 6-2
Stopping vehicle....
............................................ ...................................6-2
Preparing toolsandspare tire(ifequipped) ....
............................. 6-3
Blocking wheels....
................................................. ...............................6-5
Removing wheelcover(ifequipped) ....
........................................... 6-6
Removing tire....
...................................................... ...............................6-6Installing
sparetire....
........................................................... ..............6-7
Stowing damaged tireand tools ....
................................................ 6-7
Jump starting ....
............................................ ................................................ 6-8
Push starting ....
............................................ ............................................. 6-10
If your vehicle overheats ....
............................................ ........................6-10
T owing yourvehicle ....
................................................. ............................6-11
T owing precautions ....
...................................................... ...............6-11
T owing recommended byNISSAN ....
......................................... 6-11
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 322 of 400
> ( G L W 0 R G H O 7 $ @
6-6
In case ofemergency
REMOVING WHEELCOVER (ifequipped)
GUID-367 4401C-151D -43A1-9DF6-7296428 8CB88
SCE0630
WARNING:
Never useyour hands toremove thewheel
cover. Thismaycause personal injury.
T o remove thewheel cover, usethejack rod
*
1
as
illustrated.
Apply cloth
*
2
between thewheel andjack rodto
prevent damaging thewheel andwheel cover.
REMOVING TIRE
T32A1308 27-A4847D3 3-094A-426F- AC3E-6A473AA5D 740
JVE0165X
Jack -uppoints
Jacking upvehicle
T32A1308 27-DBAE999 F-CE6C-44E9 -9569-9ED9 514CF77B
SCE0574
WARNING:
. Besure toread andfollow theinstructions in
this section.
. DO NOTGET UNDER AVEHICLE THATIS
SUPPORTED BY A JACK .
. Never useajack which isnot provided with
your vehicle.
. The jack, which isprovided withyour vehicle,
is designed onlytolift your vehicle duringa
tire change. Donot use thejack provided
with your vehicle onother vehicles.
. Never jackupthe vehicle atalocation other
than thejack -uppoint thatisspecified.
. Never liftthe vehicle morethannecessary.
. Never useblocks onorunder thejack.
. Never startorrun theengine whilethe
vehicle ison the jack. Thevehicle maymove
suddenly, andthismay cause anaccident.
. Never allowpassengers toremain inthe
vehicle whilethetire isoff the ground. .
Besure toread thecaution labelattached to
the jack body before using.
1. Place thejack directly underthejack-up point as
illustrated sothat thetop ofthe jack contacts the
vehicle atthe jack-up point.
The jack should beplaced onfirm level
ground.
2. Align thejack head between thetwo notches
located atthe jack-up point ofeither thefront or
the rear section.
3. Fitthe groove ofthe jack head between the
notches asshown.
4. Loosen eachwheel nut,counterclockwise, oneor
two turns withthewheel nutwrench.
Do not remove thewheel nutsuntil thetire is
off the ground.
5. Carefully raisethevehicle untiltheclearance
between thetireand ground isachieved.
6. To lift the vehicle, securely holdthejack lever and
rod with both hands andturn thejack lever.
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 324 of 400
> ( G L W 0 R G H O 7 $ @
6-8
In case ofemergency
NO TE:
When stowing thejack andtools, bundle and
fasten themusing theband included withthe
tool bag, before storing them.Otherwise the
tools maycontact eachother andproduce noise.
T32A130 827-A9A95 FA9-77F4-4C CA-AD10-3D 185CD2C553
WARNING:
. Incorrect jumpstarting canlead toabattery
explosion. Thebattery explosion mayresult
in severe injuryordeath. Itmay also result in
damage tothe vehicle. Besure tofollow the
instructions inthis section.
. Explosive hydrogengasisalways present in
the vicinity ofthe battery. Keepallsparks
and flames awayfromthebattery.
. Always wearsuitable eyeprotection and
remove rings,bracelets, andanyother jew-
elry whenever workingonornear abattery.
. Never leanover thebattery whilejump
starting.
. Never allowbattery fluidtocome into
contact witheyes, skin,clothes orthe
vehicle's paintedsurfaces. Batteryfluidisa
corrosive sulfuricacidwhich cancause
severe burns.Ifthe fluid comes intocontact
with anything, immediately flushthecon-
tacted areawithplenty ofwater.
. Keep thebattery outofthe reach ofchildren.
. The booster batterymustberated at12
volts. Useofan incorrectly ratedbattery will
damage yourvehicle.
. Never attempt tojump startafrozen battery.
It could explode andcause serious
injury.
JVE0160X
QR25 engine model
JVE0161X
MR20 engine model
JVE0193X
R9M engine model
JUMP STARTING
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 325 of 400
> ( G L W 0 R G H O 7 $ @
1. Ifthe booster batteryisin another vehicle
*
B
,
position thetwo vehicles
*
A
and
*
B
to bring the
batteries intoclose proximity toeach other.
CAUTION:
If the battery ofvehicle
*
A
equipped withthe
Intelligent Keysystem isdischarged, theignition
switch cannot bemoved fromtheªLOCKº
position and,ifthe steering lockisengaged,
the steering wheelcannot bemoved. Connect
the jumper cablestothe booster vehicle
*
B
before turning orpushing theignition switchand
disengaging thesteering lock.
2. Apply theparking brake.
3. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªNº (Neutral) position.
4. Switch offallunnecessary electricalsystems
(headlights, heater,airconditioner, etc.).
5. Place theignition switchinthe ªLOCKº position.
6. Remove thevent caps, ifequipped, onthe battery .
7. Cover thebattery withafirmly wrung outmoist
cloth toreduce thehazard ofan explosion.
8. Connect thejumper cablesinthe sequence as
illustrated (
*
1
,
*
2
,
*
3
,
*
4
) .
CAUTION:
. Always connect positive +topositive +and
negative 7tobody ground, NOTto the
battery's negative7.
. Besure thatthejumper cablesdonot touch
moving partsinthe engine compartment. .
Besure thatthejumper cable's clamps do
not contact anyother metal.
9. Start theengine ofthe booster vehicle
*
B
and let
it run forafew minutes.
10. Depress theaccelerator pedalofthe booster
vehicle
*
B
at about 2,000 rpm.
11. Start theengine ofthe jumped vehicle
*
A
in the
normal manner.
CAUTION:
Never keepthestarter motorengaged formore
than 10seconds. Ifthe engine doesnotstart
right away, placetheignition switchªOFFºand
wait atleast 10seconds beforetryingagain.
12. After theengine isstarted, carefully disconnect
the jumper cablesinthe opposite sequence from
that illustrated (
*
4
,
*
3
,
*
2
,
*
1
) .
13. Remove anddispose ofthe cloth asitmay be
contaminated withcorrosive acid.
14. Replace thevent caps, ifremoved.
NO TE:
. For model withStop/Start SystemorIdling
Stop System, usethespecial batterythatis
enhanced inregard tothe charge-discharge
capacity andlifeperformance. Avoidusinga
non-special batteryforthe Stop/Start Sys-
tem orIdling StopSystem, asthis may cause
early deterioration ofthe battery oramal-
function ofthe Stop/Start SystemorIdling
Stop System. Forthebattery, itis recom-
mended touse Genuine NISSANparts.For
more information, contactaNISSAN dealer. .
For model withStop/Start SystemorIdling
Stop System, itmay take some timeuntil
Stop/Start SystemorIdling StopSystem
activates whenthebattery isreplaced orthe
battery terminal isdisconnected forex-
tended periods andthen reconnected.
In case ofemergency
6-9
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 326 of 400
> ( G L W 0 R G H O 7 $ @
6-10
In case ofemergency
T32A1308 27-F123FE9 F-EA80-4BD 4-8400-0FE8 D527FD22
Do not attempt tostart theengine bypushing the
vehicle.
CAUTION:
. Continuously Variable Transmission (CVT)/
Manual Transmission (MT)model cannot be
started bypushing. Attempting todo somay
cause damage tothe transmission.
. Three-way catalystequipped modelshould
not bestarted bypushing. Attempting todo
so may cause damage tothe three-way
catalyst.
. Never trytostart theengine bytowing.
When theengine starts,theforward surge
could cause thevehicle tocollide withthe
towing vehicle.
. Stop/Start SystemorIdling StopSystem
equipped modelcannot bestarted bypush-
ing the vehicle.
T32A130827- 0650D05A-CC 67-40AA-8C96-B273BCC7A50B
WARNING:
. Never continue drivingifyour vehicle over-
heats. Doingsocould cause avehicle fire.
. Never openthehood ifsteam iscoming out.
. Never remove theradiator orcoolant reser-
voir capwhile theengine ishot. Ifthe
radiator orcoolant reservoir capisremoved
when theengine ishot, pressurized hot
water willspurt outand possibly cause
burning, scalding orserious injury.
. Ifsteam orcoolant iscoming fromthe
engine, standclearofthe vehicle toprevent
getting burned.
. The engine cooling fancan start atany time
when thecoolant temperature exceedspre-
set degrees.
. Becareful nottoallow yourhands, hair,
jewelry orclothing tocome intocontact with,
or toget caught inthe cooling fanordrive
belts.
If your vehicle isoverheating (indicatedbythe high
temperature indicator),or ifyou feel alack ofengine
power, detectunusual noise,etc.,takethefollowing
steps:
1. Safely movethevehicle offthe road away from
traffic.
2. Turn onthe hazard indicator flasherlights.
3. Apply theparking brake.
4. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªNº (Neutral) position.
DO NOTST OP THE ENGINE . 5.
Open allthe windows.
6. Turn offthe airconditioner. Movethetemperature
control tomaximum hotand thefancontrol tohigh
speed.
7. Get outfrom thevehicle.
8. Visually inspectandlisten forsteam orcoolant
escaping fromtheradiator beforeopening the
hood. Wait until nosteam orcoolant canbeseen
before proceeding.
9. Open theengine hood.
10. Visually inspectifthe cooling fanisrunning.
11. Visually inspecttheradiator andradiator hosesfor
leakage.
If the cooling fanisnot running orthe coolant is
leaking, stoptheengine.
12. After theengine coolsdown, checkthecoolant
level inthe reservoir withtheengine running. Do
not open theradiator cap.
13. Add coolant tothe reservoir ifnecessary .
Have yourvehicle inspected/repaired ataNISSAN
dealer.
PUSH STARTING IFYOUR VEHICLE OVERHEA TS
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 346 of 400
> ( G L W 0 R G H O 7 $ @
8-10
Maintenance anddo-it-yours elf
T32A1308 27-7FBFDE4 2-D934-4EBF-A456-15EF83DB52F C
CHECKING ENGINEOILLEVEL
T32A1308 27-832AD9AE -E088-46FB-B20C-AC C097451A7F
JVM0423X
QR25 andMR20 engine
JVM0435X
R9M engine
1. Park thevehicle onalevel surface andapply the
parking brake.
2. Start theengine andwarm itup until theengine
temperature reachesthenormal operating tem-
perature (approximately 5minutes) .
3. Stop theengine.
4. Wait atleast 10minutes forthe engine oiltodrain
back tothe oilpan.
5. Remove thedipstick andwipe itclean. 6.
Reinsert thedipstick allthe way.
7. Remove thedipstick andcheck theoillevel. It
should bewithin therange
*
C
.
8. Ifthe oillevel isbelow
*
A
, remove theoilfiller cap
and pour therecommended oilinto theopening.
Do not overfill
*
B
.
When fillingtheengine oil,donot remove
the dipstick.
9. Recheck theoillevel withthedipstick.
It is normal toadd some oilbetween oil
maintenance intervalsorduring thebreak -in
period, depending onthe severity ofoperat-
ing conditions.
CAUTION:
The oillevel should bechecked regularly.
Operating yourvehicle withaninsufficient
amount ofoil can damage theengine, andsuch
damage isnot covered bythe warranty.
CHANGING ENGINEOILAND OILFILTER
T32A130827- 17863BB7-3386-4EB2-B54 2-3228E21833C2
WARNING:
. Used oilmust bedisposed ofproperly. Never
pour ordump oilinto theground, canals,
rivers, etc.It should bedisposed ofatproper
waste facilities. NISSANrecommends hav-
ing your oilchanged byaNISSAN dealer.
. Be careful nottoburn yourself, asthe
engine oilmay behot.
. Prolonged andrepeated contactwithused
engine oilmay cause skincancer.
. Avoid directskincontact withused oil.If
contacted, washthoroughly withsoap or hand
cleaner andplenty ofwater assoon as
possible.
. Store usedengine oilinmarked containers
out ofthe reach ofchildren.
V ehicle set-up
GUID-EF 5792C3-0A80 -4BDF-944F-8C21E6 FF05DC
1. Park thevehicle onalevel surface andapply the
parking brake.
2. Start theengine andwarm itup until theengine
temperature reachesthenormal operating tem-
perature (approximately 5minutes) .
3. Stop theengine.
4. Wait atleast 10minutes forthe engine oiltodrain
back tothe oilpan.
5. Raise andsupport thevehicle usingasuitable
floor jackandsafety jackstands.
.
Place thesafety jackstands underthevehicle
jack -up points.
.
A suitable adaptershouldbeattached tothe
jack stand saddle.
6. Remove theplastic engine undercover (if
equipped) .
.
Remove theplastic clipsfromtheundercover.
Engine oiland filter
T32A1308 27-6F86E2B7-D38C-4 534-AFED-674BD03BA210
QR25DE andMR20DD engine:
ENGINE OIL
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 348 of 400
> ( G L W 0 R G H O 7 $ @
8-12
Maintenance anddo-it-yours elf
JVM0421X
MR20DD engine
*
1
Oil filler cap
*
2
Oil drain plug
*
3
Oil filter
1. Place alarge drainpanunder thedrain plug.
2. Remove thedrain plugwithawrench.
3. Remove theoilfiller capand completely drainthe
oil.
If the oilfilter isto be changed, removeand
replace itat this time.
CAUTION:
Waste oilmust bedisposed ofproperly. Check
your local regulations.
4. Remove theplastic coverovertheoilfilter location
by removing thesmall plastic clipsasillustrated.
(For QR25DE engine)
5. Loosen theoilfilter withanoilfilter wrench.
6. Remove theoilfilter byturning itby hand.
7. Wipe theengine oilfilter mounting surfacewitha
clean cloth.
Be sure toremove anyoldgasket remaining onthe
mounting surface. 8.
Apply newengine oiltothe gasket ofthe new oil
filter.
9. Screw inthe oilfilter untilaslight resistance isfelt
and then tighten anadditional 2/3ofaturn to
secure thefilter.
Oil filter tightening torque:
15 to20 N´m
(1.5 to2.0 kg-m, 11to15 ft-lb)
10. Clean andreinstall thedrain plugandnew washer.
Securely tightenthedrain plugwithawrench. Do
not use excessive force.
Drain plugtightening torque:
29 to39 N´m
(3.0 to4.0 kg-m, 22to29 ft-lb)
11. Refill therecommended engineoiland quantity .
(See ªRecommended Fluids/lubricants andcapa-
citiesº (P.9-2) .)
When fillingtheengine oil,donot remove
the dipstick.
12. Securely installtheoilfiller cap.
13. Start theengine.
14. Check thedrain plugforany sign ofleakage.
15. Dispose ofthe used oilinthe proper manner.
Check yourlocal regulations.
16. Check theengine oillevel according tothe proper
procedure. (SeeªChecking engineoillevelº (P.8-
10) .) R9M
engine:
GUID-2201 8305-9BAB- 4201-B6FC-C08EB94A EAE0
JVM0436X
*
1
Oil filler cap
*
2
Oil drain plug
*
3
Oil filter
& R Q G L W L R Q
( [ F H S W I R U & K L Q D
Page 349 of 400
> ( G L W 0 R G H O 7 $ @
SDI2149
1 Oilfiller element
2 O-ring
3 Oilfilter cover
1. Place alarge drainpanunder thedrain plug.
2. Remove thedrain plugwithawrench.
3. Remove theoilfiller capand completely drainthe
oil.
If the oilfilter isto be changed, removeand
replace itat this time.
CAUTION:
Waste oilmust bedisposed ofproperly. Check
your local regulations.
4. Loosen theoilfilter cover withawrench.
5. Remove theengine oilfilter cover thentheoilfilter
element.
6. Remove therubber O-ring fromthefilter cover.
7. Wipe theentire oilfilter cover withaclean cloth.
Be sure toremove anyoldO-ring remaining onthe
mounting surface. 8.
Apply newengine oiltothe O-ring.
Install thenew O-ring onthe new oilfilter element.
9. Insert theoilfilter element intotheengine oilfilter
cover.
10. Screw inthe oilfilter cover untilaslight resistance
is felt, and then tighten thefilter completely .
Oil filter cover tightening torque:
25 N´m
(2.6 kg-m, 18ft-lb)
11. Clean andreinstall thedrain plugandnew washer.
Securely tightenthedrain plugwithawrench. Do
not use excessive force.
Drain plugtightening torque:
50 N´m
(5.1 kg-m, 36.9ft-lb)
12. Refill therecommended engineoiland quantity .
(See ªRecommended Fluids/lubricants andcapa-
citiesº (P.9-2) .)
13. Securely installtheoilfiller cap.
14. Start theengine.
15. Check thedrain plugforany sign ofleakage.
16. Dispose ofthe used oilinthe proper manner.
Check yourlocal regulations.
17. Check theengine oillevel according tothe proper
procedure. (SeeªChecking engineoillevelº (P.8-
10) .)
After operation
T32A1308 27-3D1A869 1-255E-47E3-9C50-DDE5 E8CFBD36
1. Lower thevehicle carefully tothe ground.
2. Dispose ofwaste oiland filter properly .
PRO TECT ENVIRONMENT
T32A1308 27-208605 74-F3E8-4014 -8CD9-B62C347302 4F
It is illegal topollute drains,watercourses andsoil. Use
authorized wastecollection facilities,including civil
amenity sitesandgarages providing facilitiesfor
disposal ofused oiland used oilfilters. Ifin doubt,
contact yourlocal authority foradvice ondisposal.
The regulations concerningthepollution ofthe
environment willvary from country tocountry.
Maintenance anddo-it-yours elf
8-13
& R Q G L W L R Q
( [ F H S W I R U & K L Q D