ignition OLDSMOBILE AURORA 1995 User Guide

Parking Brake
To set the parking brake,
hold the regular brake pedal
down with your right foot.
Push down the parking
brake pedal with your
left
foot. If the ignition is on,
the parking brake indicator
light will come on.
If
you try to drive off with the parking brake on, the
parking brake indicator light stays on. The PARK
BRAKE SET message will appear in the Driver
Information Center, and a chime will sound until you
release the parking brake
or recycle the ignition. This
vehicle has
a PUSH TO RELEASE parking brake
pedal. To release
the parking brake, hold the regular
brake down and push
the parking brake pedal with your
left foot. This will unlock the pedal. When you lift your
left foot, the parking brake pedal will follow it
to the
released position.
NOTICE:
Driving with the parking brake on can cause
your rear brakes to overheat. You may have
to
replace them, and you could also damage other
parts
of your vehicle.
If you are towing a trailer and are parking on any hill,
see “Towing a Trailer” in the Index. That part shows
what
to do first to keep the trailer from moving.
2-24
ProCarManuals.com

Shifting Into PARK (P)
1. Hold the brake pedal down with your right foot and
set the parking brake.
2. Move the shift lever into the PARK (P) positions as
follows:
0 Hold in the button on the lever.
Push the lever all the way toward the front of
your vehicle.
3. Move the ignition key to LOCK.
4. Remove the key and take it with you. If you can
walk away from your vehicle with the ignition key in
your hand, your vehicle is in PARK (P).
2-25
ProCarManuals.com

Shifting Out of PARK (P)
Your Aurora has a brake-transaxle shift interlock. You
have to fully
apply your regular brake before you can
shift from PARK (P) when the ignition is in the
ON
position. See “Shifting the Automatic Transaxle” in the
Index.
If you cannot shift out of PARK (P), ease pressure
on
the shift lever--push the shift lever all the way into
PARK (P) as you maintain brake application. Then
move the shift lever into the gear you wish. Press the
shift lever button before moving the shift lever.
If you ever hold the brake pedal down but still can’t
shift out of PARK (P), try this:
1. Turn the key to OFF. Open and close the driver’s
door to turn off the Retained Accessory Power
feature.
2. Apply and hold the brake until the end of step 4.
3. Shift to NEUTRAL (N).
4. Start the vehicle and then shift to the drive gear you
want.
5. Have the vehicle fixed as soon as you can.
Parking Over Things That Burn
2-27
ProCarManuals.com

Power Windows
Follow the proper steps to be sure your vehicle won’t
move. See “Shifting Into PARK (P)” in the Index.
If you are parking on a hill and if you’re pulling a
trailer, also see “Towing a Trailer” in the Index. Switches
on the driver’s armrest control each
of the
windows when the ignition is on. In addition, each
passenger door
has a switch for its own window.
The driver’s window switch has an express down
feature.
When it is held rearward for more than half a
second, the window will lower completely. The window
can be opened
in smaller amounts by pressing the switch
rearward and releasing
it immediately.
To stop the window while it is lowering, press the
switch again, then release. To raise the window, hold the
switch forward.
ProCarManuals.com

Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load, and the steepness of the hills.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear to
keep your speed down. Of course, applying the brake takes
yon out of cruise control. Many drivers find this to be
too
much trouble and don’t use cruise control on steep hills.
To Get Out of Cruise Control
There are two ways to turn off the cruise control:
Step lightly on the brake pedal; or
Move the cruise switch to OFF. (The CRUISE light
will go out.)
To Erase Cruise Control Memory
When you turn off the cruise control or the ignition, or
shift into
PARK (P), your cruise control set speed
memory is erased.
2-38
ProCarManuals.com

Daytime Running Lamps (Canada Only)
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful
in many different driving
conditions, but they can be especially helpful
in the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work,
so be sure it isn’t covered. The DRL system
will make your low-beam headlamps conle on at
a
reduced brightness when:
0 The ignition is ON,
The headlamp switch is OFF, and
0 The transaxle is not in PARK (P).
When the DRL are on,
only your low beam headlamps
will be on. The taillamps, sidemarker and other lamps
won’t be on. Your instrument panel won’t be
lit up either.
When it’s dark enough outside, your
low beam
headlamps will change to
full brightness automatically.
The other lamps that come on with your headlamps
will
also come on. When
it’s bright enough outside, the regular lamps
will
go off, and your low beam headlamps will change to the
reduced brightness of DRL.
To idle your vehicle with the DRL off, shift the
transaxle into PARK
(P). The DRL will stay off until
you shift out of PARK (P). If it’s dark, you must also
move the Twilight Sentinel control to MIN.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Fog Lamps
To turn on the fog lamps,
first turn
on the parking
lamps or headlamps. Then
press the fog lamp switch.
A light will glow on the
switch when the switch
is
on. To turn off the fog
lamps, press
it again. The
fog lamps will also switch
off when you turn on your
high beam headlamps.
but
will turn on again when you
switch to low beams.
2-41
ProCarManuals.com

To operate the Twilight Sentinel, rotate the Twilight
Sentinel control to
MAX for a three-minute delay.
Rotate it toward
MIN to reduce the delay. Rotate the
control all the way to
MIN to turn off the Twilight
Sentinel. These
lamps work even
when the ignition is off. To
avoid draining your vehicle’s battery, be sure to turn off
all front and rear reading lamps when leaving your
vehicle.
Front Reading Lamps Rear Reading Lamps
These lamps and
the interior courtesy lamps will come
on when you open a door. They will turn off when
you
turn on the ignition. If the door is left open, they will
turn off after about
10 minutes.
To turn on the reading lamps when the doors are closed,
press the button behind the lamp you want
on. Press it
again
to turn the lamp off.
These lamps go on when you open the doors. You can
also turn them on by pressing the button to the side of
the lamp. Press it again to turn them off.
These lamps work even when the ignition
is off. To avoid
draining
your vehicle’s battery, be sure to turn off all front
and rear reading lamps when leaving your vehicle.
2-43
ProCarManuals.com

Sunroof (Option)
Your express open sunroof provides an airy, spacious feel
to your vehicle’s interior and can
also increase ventilation.
It includes a sliding glass panel and a sliding sunshade.
The control switch
will work only when the ignition is
on, or when Retained Accessory Power
is active.
L
To open the sunroof, press the control switch rearward
and release
it to open the glass panel and sunshade.
If you want to stop the sunroof in a partially open
position, lightly press the switch again.
To fully open the
sunroof, press the switch rearward again. The sunshade
can also be opened by hand.
To close the sunroof, press and hold the control switch
forward to close the
glass panel.
The sunroof glass panel cannot be opened or closed if
your vehicle has an electrical failure.
To open the sunroof rear vent, open the sunshade by
hand. Press the control switch forward when the sunroof
is closed.
To close the sunroof rear vent, press the switch
rearward.
2-54
ProCarManuals.com

The Aurora instrument panel is designed to let you
know at a glance how your vehicle is running. You’ll
know how fast you’re going, how much fuel you’re
using, and many other things you’ll need
to drive safely
and economically.
The main components
of your instrument panel are:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Power Mirrors Control Switch
Fog Lamp Switch
Turn SignalMultifunction Lever
Instrument ClusterIGages
Hazard Warning Flashers Switch
Horn
Windshield Wiper/Washer Control
Driver Information Center
Climate Controls
Audio System
Glove
Box (Trunk Security Override Switch inside) 12.
Passenger Side Air Bag
13. Accessory Power Outlet
14. Gearshift Lever
15. Selectable Shift
16. Traction Control Button
17. Ashtray and Lighter
18. Fuel Door Release Switch
19. Trunk Release Switch
20. Steering Wheel Touch Controls for Audio System
21. Ignition Switch
22. Driver Side Air Bag
23.
Tilt Steering Wheel Lever
24. Steering Wheel Touch Controls for Climate Control
System
25. Twilight Sentinel Control
26. Instrument Panel Intensity Control
ProCarManuals.com

Safety Belt Reminder Light
FASTEN
BELTS
When the key is turned to RUN or START, a chime will
come on for about eight seconds to remind people to
fasten their safety belts.
The safety belt light will also
come on and stay on for about
70 seconds. If the driver’s
belt is already buckled, neither the chime nor the light
will come on.
Air Bag Readiness Light
There is an air bag readiness light on the instrument
panel, which shows
AIR BAG. The system checks the
air bag’s electrical system for malfunctions.
The light
tells you
if there is an electrical problem. The system
check includes the air bag sensors and modules, the
wiring and
the diagnostic module. For more information
on the air bag system, see “Air
Bag” in the Index.
AIR BAG
You will see this light
flash for
a few seconds
when you turn your
ignition to RUN or
START. Then the light
should go out. This
means the system is
ready.
If the air bag readiness light doesn’t come on when you
start your vehicle, or stays on, or comes on when you
are driving, your air bag system may not work properly.
Have your vehicle serviced right away.
2-64
ProCarManuals.com