buttons Oldsmobile Aurora 2001 Owner's Manuals
[x] Cancel search | Manufacturer: OLDSMOBILE, Model Year: 2001, Model line: Aurora, Model: Oldsmobile Aurora 2001Pages: 376, PDF Size: 2.67 MB
Page 84 of 376
2-14 Resynchronization
Pressing the transmitter buttons numerous times
(approximately 250 times) out of the vehicle's operating
range may cause the transmitter not to work. Replacing
the battery and pressing the transmitter buttons out
of range will also cause the transmitter not to work.
If only the instant alarm works, the transmitter needs
to be resynchronized to the receiver. Resynchronize by
pressing and holding both the buttons with the lock
and unlock symbols at the same time for about eight
seconds. You must be within range of the vehicle.
Once the transmitter has been resynchronized, the locks
will cycle (the horn may chirp and the exterior lamps
may flash) depending on the security feedback settings.
The system should now operate properly.
Trunk
CAUTION:
It can be dangerous to drive with the trunk lid
open because carbon monoxide (CO) gas can
come into your vehicle. You can't see or smell
CO. It can cause unconsciousness and even death.
If you must drive with the trunk lid open or if
electrical wiring or other cable connections must
pass through the seal between the body and the
trunk lid:
Make sure all other windows are shut.
Turn the fan on your heating or cooling
system to its highest speed with the setting
on any airflow selection except RECIRC.
That will force outside air into your vehicle.
See ªComfort Controlsº in the Index.
If you have air outlets on or under the
instrument panel, open them all the way.
See ªEngine Exhaustº in the Index.
Page 129 of 376
2-59
Your vehicle's engine should be turned off while
programming the transmitter. Follow these steps to
program up to three channels:
1. If you have previously programmed a transmitter
channel, proceed to Step 2. Otherwise, hold
down the two outside buttons on the HomeLink
Transmitter until the indicator light begins to flash
rapidly (after 20 seconds). Then release the buttons.
This procedure initializes the memory and erases any
previous settings for all three channels.
2. Decide which one of the three channels you want to
program. Hold the end of the hand
-held transmitter
about 2 to 5 inches (5 to 13 cm) away from the
surface of the HomeLink Transmitter so that you
can still see the indicator light.
3. Using both hands, press the hand
-held transmitter
button and the desired button on the HomeLink
Transmitter. Continue to press both buttons
through Step 4.
4. Hold down both buttons until you see the indicator
light on the HomeLink Transmitter flash slowly and
then rapidly. The rapid flashing indicates that the
HomeLink Transmitter has been programmed.
Release both buttons once the indicator light starts
to flash rapidly.If you have trouble programming the HomeLink
Transmitter, make sure that you have followed the
directions exactly as described. The HomeLink
Transmitter may not work with older garage door openers
that do not meet current Federal Consumer Safety
Standards. If you cannot program the transmitter after
repeated attempts, refer to ªRolling Code Programmingº
later in this section or contact the HomeLink Transmitter
manufacturer at 1
-800-355-3515.
Be sure to keep the original hand
-held transmitter
in case you need to erase and reprogram the
HomeLink Transmitter.
Note to Canadian Owners: During programming,
the hand
-held transmitter may automatically stop
transmitting after one or two seconds. In this case, you
should press and repress the button on the hand
-held
transmitter every two seconds without ever releasing the
button on the HomeLink Transmitter. Release both
buttons when the indicator light on the HomeLink
Transmitter begins to flash rapidly.
Page 131 of 376
2-61
3. Return to the HomeLink Transmitter in your
vehicle and firmly press and release the HomeLink
Transmitter button you have already programmed for
two to three seconds. Press and release the button
again (you may need to do this step up to three
times) to make sure that the HomeLink Transmitter
has been trained to the garage door opener motor
head unit. Check that the training was successful.
The garage door opener should now recognize the
HomeLink Transmitter. You may either use the
HomeLink Transmitter or the hand
-held transmitter
to open the garage door.
If after following these instructions, you still have problems
training the garage door opener, contact the HomeLink
Transmitter manufacturer at 1
-800-355-3515.
Erasing Channels
To erase all three programmed channels, hold down the
two outside buttons until the indicator light begins to
flash (after 20 seconds). Release both buttons.
Accessories
Accessories for the HomeLink Transmitter are available
from the manufacturer of the unit. If you would like
additional information, please call 1
-800-355-3515.
Page 133 of 376
2-63
The main components of your instrument panel are:
A. Air Outlet
B. Turn Signal/Multifunction Lever
C. Steering Wheel Controls for Climate Control System
D. Steering Wheel Controls for Audio System
E. Windshield Wiper/Washer Control
F. Driver Information Center (DIC)
G. Hazard Warning Flasher Button
H. Climate Control System
I. Instrument Panel Brightness ControlJ. Trip Odometer Buttons
K. Hood Release
L. Parking Brake
M. Cruise Control Lever
N. Ignition Switch
O. Audio System
P. Accessory Power Outlet
Q. Glove Box (Trunk Release Lockout Switch inside)
Page 148 of 376
2-78
Driver Information Center (DIC)
The Driver Information Center (DIC) displays
information in either English or metric. When the
system is on or off, push the ON/OFF button down
for three seconds to change the display between English
and metric. This will also change the digital screen for
the climate control system between English and metric.The DIC has different display modes which can be
accessed by pressing the four buttons on the DIC.
These buttons are labeled ON/OFF, SELECT right
arrow, SELECT down arrow and RESET. The button
functions are detailed in the following.
Turn on the system by pressing the ON/OFF button
once. When you turn on the ignition, the DIC will be in
the mode last displayed when the engine was turned off.
Keep in mind that this also applies to the OFF mode.
To turn off messages on the DIC (except LOW OIL
PRESSURE, LOW BRAKE FLUID, PARK BRAKE
SET, STARTING DISABLED and the HOT...STOP
ENGINE warning), press the RESET button.
Pressing the SELECT right arrow button will allow
you to access the following modes, DATE/ET, FUEL,
ECON, OIL and GAGE. While in any of these modes,
warning messages can interrupt and take over the
display until you acknowledge the message, or the
condition causing the problem goes away.
Page 149 of 376
2-79 Date/Elapsed Time
Pressing the SELECT down arrow while in DATE/ET
mode will allow you to choose between the elapsed time
and date menus.
Date
To set the date, press and hold the RESET button for
two seconds while the date is being displayed on the
DIC. When the date set mode is entered the display
will show the following:
YEAR?_____ MM/DD/00
The year will be flashing. To increase the item that is
flashing press SELECT right arrow. To decrease the
item that is flashing press SELECT down arrow.
When you reach the current year press the RESET
button. The DIC will ask for the month. The month
will flash the same as the year. Use the SELECT
buttons to reach the current month and press RESET.
The DIC will then ask for the day. The day will flash the
same as the year. Use the SELECT buttons to reach the
current day. Press the RESET button again and the set
display will stop flashing and go back to the normal
operation mode.Elapsed Time (ET)
When the ignition is on, the DIC can be used as a
stopwatch. The display will show hours and minutes.
The elapsed time indicator will record up to 100 hours,
then it will reset to zero and continue counting. Press
SELECT down arrow while in the DATE/ET mode,
and the display will show the amount of time that has
elapsed since the elapsed time indicator was last reset
(not including time the ignition is off), such as:
01:08 ELAPSED TIME
To start or stop the counting of time, press the RESET
button briefly. If the colon (:) in the time is flashing,
time is being counted. Time is displayed in hours and
minutes. Seconds are not displayed. Time will continue
to be counted as long as the ignition is on, even if
another display is being shown on the DIC.
To reset elapsed time to zero, press RESET button
for three seconds while the elapsed time is displayed.
Page 153 of 376
2-83 DIC Personalization
The DIC can be used to program the following personal
choice features available with your vehicle:
Automatic Door Locks
Window Lockout
Security Feedback
Delayed Locking
Perimeter Lighting
Driver ID
Memory Seats
Parallel Park Assist Mirror (Tilt Mirror)
To access the personalization menu, the vehicle must be
in PARK (P) with the ignition in RUN and no warning
messages displayed on the DIC. You must then press
and hold both of the SELECT buttons for three seconds.
This will display the personalization menu.The DIC display will show the following:
FEATURE PROGRAMMING
PRESS SELECT DOWN TO
SELECT MENU OPTIONS
PRESS SELECT RIGHT TO
CHANGE SETTINGS
The next item to be displayed is DRIVER 1 or
DRIVER 2. To change the driver number, press the
SELECT right arrow. The driver number that you
select should correspond with the number on the back
of your remote lock control transmitter. Once the correct
driver number has been selected, press the SELECT
down arrow to enter your choice and move on to the
next selection.
Page 163 of 376
3-2
Comfort Controls
This section tells you how to operate your climate
control system.
Your vehicle may be equipped with a passenger
compartment air filter. For more information, see
ªPassenger Compartment Air Filterº in the Index.
Comfort Controls Personalization
(If Equipped)
This feature allows two different drivers to store and
recall their own climate control settings for temperature,
air delivery mode and fan speed. The personal choice
settings recalled are determined by the transmitter used
to enter the vehicle. After the button with the unlock
symbol on a remote keyless entry transmitter is pressed,
and the ignition is in RUN, the climate control will
adjust to the last settings of the identified driver. The
settings can also be changed by pressing one of the
memory buttons (1 or 2) located on the driver's door,
until you hear two beeps. When adjustments are made,
the new settings are automatically saved for that driver.
Automatic Electronic Climate Control
Your vehicle is equipped with either a Single Zone or
a Dual Zone Automatic Electronic Climate Control
System. You can use the automatic setting or override
the automatic setting by using the manual controls.
Your vehicle also has the flow
-through ventilation
system described later in this section.
AUTO
-PUSH Knob
By pressing the AUTO
-PUSH knob, you have
selected the electronic climate control system to be in
the automatic mode. The climate control system will
automatically control the air temperature, air inlets, air
distribution and the fan speed based on your selected
temperature setting as well as on the temperature inside
the vehicle, the outside temperature and the sun load.
Page 164 of 376
3-3
When you press the AUTO-PUSH knob, the lights
under the AUTO
-PUSH and AUTO FAN knobs
will illuminate. Your current comfort setting will be
shown in the digital display.
Set the comfort level you want inside the vehicle by
using the colored buttons located below the climate
control display.
Turn the AUTO
-PUSH knob to select the
manual air delivery mode operation of the climate
control system.
Temperature Buttons
To adjust the comfort level you want maintained inside
the vehicle, use the red and blue buttons located below
the digital display. If you want a warmer comfort level,
push the red button. If you want a cooler comfort level,
push the blue button. Your selected comfort setting will
be shown on the digital display for five seconds, then
the outside temperature will be displayed.Mode Control
Turn the AUTO
-PUSH knob to deliver air through
the floor, panel or windshield outlets. The system will
stay in the selected mode until the AUTO
-PUSH knob
is pressed.
AUTO FAN Knob
This knob controls the fan speed in either an automatic
mode or a manual mode.
Pressing the AUTO FAN knob puts the fan control
in the automatic mode. The AUTO FAN light will
appear below the knob. The fan speed indicators
will not be illuminated when the system is in the
automatic fan control mode.
Turning the AUTO FAN knob selects a manual
fan speed. Turn this knob clockwise to raise the fan
speed. Turn this knob counterclockwise to lower the
fan speed. Turning the AUTO FAN knob overrides
the automatic fan control mode. The fan speed
indicators will be illuminated while in the manual
fan control mode.
Page 165 of 376
3-4
Automatic Operation
Press the AUTO
-PUSH knob when you want the
system to automatically adjust the interior temperature
to your preference. When the system is set for automatic
operation, air will come from the floor, the panel outlets
or the windshield outlets depending on the temperature
inside the vehicle, the outside temperature, the engine
coolant temperature and the sun load. Fan speed will
vary as the system reaches and maintains the comfort
setting you have selected.
To find your comfort setting, start with the system in
automatic mode by pressing the AUTO
-PUSH knob.
Adjust the comfort setting by using the red and blue
buttons located below the digital display until you
reach a setting of 75F (24C) on the display. Give the
vehicle about 30 minutes to stabilize and then readjust
the comfort setting if necessary. The display will show
the comfort setting for five seconds and then it will
show the outside temperature.In cold weather, the system will delay turning on the
fan to avoid blowing cold air. The length of the delay
depends on the engine coolant temperature and the
outside temperature. Turning the AUTO FAN knob
will override this delay by turning off the automatic fan
mode and changing the fan speed.
Your automatic electronic climate control system has a
sun sensor located on the top of the instrument panel
that detects direct sunlight. To keep you and your
passengers comfortable, the system may supply cooler
air to the side toward the sun. Be careful not to put
anything over this sun sensor. The automatic electronic
climate control system may not operate correctly if this
sensor is covered.
To change the automatic electronic climate control
display from an English display to a metric display,
push the OFF button located in the Driver Information
Center (DIC) for two seconds. The display in the DIC
will also change from an English to a metric display. To
return to an English display, repeat the above procedure.