display Oldsmobile Aurora 2001 Owner's Manuals

2-7 Power Door Locks
With power door locks,
you can lock or unlock all
the doors of your vehicle
using the driver's or the
front passenger's door
lock switch.
Door Ajar Reminder
If a door is not fully closed when the transaxle is in gear, a
chime will sound and the Driver Information Center (DIC)
will display one of these messages:

DRIVERS DOOR AJAR

PASSENGER DOOR AJAR

LEFT REAR DOOR AJAR

RIGHT REAR DOOR AJAR
Programmable Automatic Door Locks
This is a personalization feature that programs your door
locks to automatically lock or unlock your vehicle.
This feature also allows you to program the vehicle to
lock all doors when shifting out of PARK (P). Also, you
can program the door locks to do one of the following:

Unlock just the driver's door when shifting back
into PARK (P),

unlock all doors when shifting back into PARK (P),

unlock just the driver's door when turning the
ignition to LOCK,

unlock all doors when turning the ignition to
LOCK, or

no automatic door unlock when shifting into
PARK (P) or turning the ignition to LOCK.
You can also program this feature to be turned off.
Then you will not have automatic door lock or unlock.
This feature will function when you close the doors and
turn on the ignition. If someone needs to get out while
you're not in PARK (P), have that person use the manual
or power door lock. When the door is closed again, it
will not lock automatically. Use the manual or power
lock to lock the door again.

2-21
Ignition Positions
With the ignition key in the ignition switch, you can turn
the switch to four different positions.
LOCK (A): This is the only position in which you
can remove the key. This position locks your ignition,
steering wheel and transaxle. It's a theft
-deterrent feature.
NOTICE:
If your key seems stuck in LOCK and you can't
turn it, be sure you are using the correct key;
if so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. But turn the key only with your hand.
Using a tool to force it could break the key or the
ignition switch. If none of this works, then your
vehicle needs service.
ACCESSORY (B): This position lets you use your
electrical power accessories such as power windows,
power sunroof (option), radio and the windshield wipers.
RUN (C): This is the position the switch returns to after
you start your engine and release the switch. This is the
position for normal driving. Even when the engine is not
running, you can use RUN to operate your electrical
power accessories and to display some instrument panel
warning lights.
START (D): This position starts your engine. When
the engine starts, release the key. The ignition switch
will return to RUN for normal driving.

2-36
As you signal a turn or a lane change, if the arrows
flash very fast, a bulb may be burned out and other
drivers won't see your turn signal.
If a bulb is burned out, replace it to help avoid
an accident.
If the arrows don't go on at all when you signal a turn,
check the fuse (see ªFuses and Circuit Breakersº in the
Index) and for burned
-out bulbs.
Turn Signal On Chime
If your turn signal is left on for more than 0.8 miles
(1.3 km), a chime will sound at each flash of the turn
signal and the DIC will display the TURN SIGNAL
ON? reminder message. To turn off the chime and
message, move the turn signal lever to the off position.
To turn off the DIC message while the turn signal is
still active, press any button on the DIC.
Headlamps
The headlamp control
is located on the turn
signal/multifunction lever.
Turn the control to this symbol to turn on
the following:

Parking Lamps

Sidemarker Lamps

Taillamps

License Plate Lamps

Instrument Panel Lights

2-45
With your headlamp control in AUTO when it is
dark enough outside, your low
-beam headlamps will
automatically come on. The other lamps that turn on
with your headlamps will also turn on. When it is bright
enough outside, the regular lamps will go off, and your
high
-beam headlamps change to the reduced brightness
of DRL.
To turn off all exterior lighting at night when you are
parked, turn the headlamp control all the way toward
OFF. The DRL will turn on automatically and the
HEADLAMPS SUGGESTED message will be
displayed on the DIC when you move the transaxle
out of PARK (P).
If the headlamp control is in the parking lamps position
at night, only the parking lamps will be on. If the
transaxle is out of PARK (P), only the parking lamps
will be active and the HEADLAMPS SUGGESTED
message will be displayed on the DIC.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Automatic Headlamps
The automatic headlamps will keep your headlamps on
when it is dark outside and the ignition is in RUN.
It's possible that your headlamps may go out if you
drive from a dark area into a bright area like a lighted
parking lot. If this happens, turn on your headlamps
with the regular headlamp switch.
Light Sensor
Your automatic headlamps and Daytime Running Lamps
work with the light sensor on top of the instrument
panel. Don't cover it up. If you do it will read ªdarkº
and the automatic headlamp lighting will turn on.
Exterior Lighting Battery Saver
If the manual lamp control has been left on, the exterior
lamps will turn off approximately 10 minutes after the
ignition is turned to LOCK and any door has been
opened. This protects against draining the battery in
case you have accidentally left the headlamps or parking
lamps on. If you need to leave the lamps on for more
than 10 minutes, use the manual control to turn the lamps
back on after the ignition has been turned to LOCK and
any door has been opened. To delay the lamps from
turning off, see ªAutomatic Headlampsº in the Index.

2-46
Interior Lamps
Instrument Panel Brightness Control
The instrument panel
brightness control is located
on the driver's side of the
instrument panel.
When it is dark outside, you can brighten or dim
your instrument panel cluster lights by turning the
dimmer knob.
Turn the knob clockwise to brighten the instrument
panel cluster lights and displays. Turn the knob
counterclockwise to dim the instrument panel cluster
lights and displays.
If it is day and your parking lamps are on, the
instrument panel cluster lights and displays will
come on at full intensity and will not be adjustable. If it is dark enough outside and your parking lamps are
on, the instrument panel cluster lights and displays and
the backlighting for the door and steering column
switches will come on, and can also be adjusted.
Courtesy Lamps
If it is dark enough outside and the front reading lamp
slider control is in the AUTO position, when any door is
opened all of the vehicles courtesy lamps will come on.
See ªReading Lampsº in the Index. They make it easier
for you to enter and leave the vehicle. The courtesy lamps
will remain on for about 25 seconds after all doors have
been closed. They will then theater dim to off.
Move the front reading lamp slider control in the
overhead console to ON to turn on the interior courtesy
lamps. When the control is moved back to either OFF
or AUTO, the courtesy lamps will immediately turn off.
If the control is OFF when the doors are opened, only
the lower instrument panel courtesy lamps will come on.
Also, if the control is OFF when illuminated entry or
delayed exit lighting are active, only the lower
instrument panel courtesy lamps will be on.
If a door is left ajar, your interior lamps will turn off
after 10 minutes to save your battery.

2-48 Parade Dimming
To activate the instrument panel backlighting during
the day, turn the headlamp switch to the parking lamp
position. Dimming of the instrument panel display is
not possible during daylight hours. The instrument panel
display can only be adjusted when the parking lamps
are on and it is dark outside.
Perimeter Lighting
When the unlock symbol on the remote lock control
transmitter is pressed, the DRL headlamps, parking
lamps and back
-up lamps will turn on for approximately
25 seconds if it is dark enough outside.
This feature can be programmed on or off for each
transmitter. You can also program how long the
exterior lamps will stay on after unlocking the vehicle.
You must program this feature through the Driver
Information Center (DIC). See ªDIC Personalization
Programmingº in the Index.
Front Reading Lamps
These lamps and the interior courtesy lamps will come
on when you open a door. They will turn off when you
turn on the ignition. If a door is left open, they will turn
off after about 10 minutes.
To turn on the reading lamps when the doors are closed,
press the button under the lamp you want on. Press it
again to turn the lamp off.
These lamps work even when the ignition is off. To avoid
draining your vehicle's battery, be sure to turn off all
front and rear reading lamps when leaving your vehicle.

2-49 Rear Reading Lamps
These lamps will come on when you open the doors.
You can also turn them on by pressing the button on the
side of the lamp. Press it again to turn them off.
Inadvertent Power Battery Saver
This feature is designed to protect your vehicle's
battery against drainage from the interior lamps,
trunk lamp, glove box lamp or cigarette lighters.
When the ignition is turned off, the power to these
features will automatically turn off after 10 minutes.Power will be restored for an additional 10 minutes if
any door is opened, the trunk is opened or the courtesy
lamp switch is turned on. To restore power back to
the cigarette lighters the ignition must be turned back
to RUN.
Battery Load Management
The battery load management feature is designed to
monitor the vehicle's electrical load and determine when
the battery is in a heavy discharge condition. During
times of high electrical loading, the engine may idle at a
higher RPM setting than normal to make sure the battery
charges. High electrical loads may occur when several
of the following are on: headlamps, high beams, fog
lamps, rear window defogger, high blower fan, heated
seats and engine cooling fans.
If your vehicle's battery remains in a heavy discharge
condition for a long period of time, the blower fan,
rear defogger, heated seats and heated mirrors will be
disabled and the DIC will display BATTERY SAVER
ACTIVE. This can happen either under long periods of
idling or low speed driving with high electrical loading,
or in the event of a charging system fault.

2-50
Mirrors
Electrochromic Day/Night Rearview Mirror
with Compass
Your vehicle has an electrochromic inside rearview
mirror with a compass. Your vehicle's mirror may also
contain OnStar

controls.
This is the on/off button for mirrors equipped
with OnStar controls.
Pressing the MIRROR button (or the on/off button for
mirrors equipped with OnStar controls) located at the
bottom of the mirror, turns the automatic dimming
feature on or off.
The mirror also includes an eight
-point compass display
in the upper right corner of the mirror face. When on, the
compass automatically calibrates as the vehicle is driven.
When cleaning the mirror, use a paper towel or similar
material dampened with glass cleaner. Do not spray
glass cleaner directly on the mirror as that may cause
the liquid cleaner to enter the mirror housing.Mirror Operation
To turn on the automatic dimming feature, press MIRROR
(or press and hold the on/off button for about three seconds
for mirrors equipped with OnStar controls). To turn off
automatic dimming, press MIRROR (or press and hold
the on/off button for about three seconds for mirrors
equipped with OnStar controls) again. The green indicator
light will be illuminated when this feature is active.
The automatic dimming feature will be active each time
the vehicle is started.
Compass Operation
Press COMPASS (or the on/off button for mirrors equipped
with OnStar controls) once to turn the compass on or off.
When the ignition and the compass feature are on, the
compass will show two character boxes for approximately
two seconds. After two seconds, the mirror will display the
compass heading.
Compass Calibration
If after two seconds, the display does not show a compass
heading (ªNº for North, for example), there may be a
strong magnetic field interfering with the compass. Such
interference may be caused by a magnetic antenna mount,
magnetic note pad holder or a similar magnetic item.
If the letter ªCº should ever appear in the compass
window, the compass may need calibration.

2-51
The mirror can be calibrated in one of two ways:

Drive the vehicle in circles at 5 mph (8 km/h) or
less until the display reads a direction, or

drive the vehicle on your everyday routine.
Mirrors equipped with OnStar controls can be placed in
calibration mode by pressing and holding the on off
button until a ªCº is shown in the compass display.
Compass Variance
The mirror is set in zone eight upon leaving the factory.
It will be necessary to adjust the compass to compensate
for compass variance if you live outside zone eight.
Under certain circumstances, as during a long distance
cross
-country trip, it will be necessary to adjust for
compass variance. Compass variance is the difference
between earth's magnetic north and true geographic
north. If not adjusted to account for compass variance,
your compass could give false readings.
To adjust for compass variance:
1. Find your current location and variance zone number
on the following zone map.
2. Press and hold COMPASS (or the on/off button for
mirrors equipped with OnStar controls) until a zone
number appears in the display.
3. Once the zone number appears in the display, press
the COMPASS (or the on/off button for mirrors
equipped with OnStar controls) button quickly until
the correct zone number appears in the display.
Stop pressing the button and the mirror will
return to normal operation. If ªCº appears in the
compass window, the compass may need calibration.
See ªCompass Calibrationº explained previously.

2-65 Speedometer and Odometer
Your speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (km/h). Your
odometer shows how far your vehicle has been driven,
in either miles (used in the United States) or kilometers
(used in Canada).
The speedometer shows a top speed of 140 mph
(220 km/h). This is not intended to be the vehicle's
top speed.
You may wonder what happens if your vehicle needs a
new odometer installed. If the new one can be set to
the mileage total of the old odometer, then it must be.
But if it can't, then it's set at zero and a label must be
put on the driver's door to show the old mileage reading
when the new odometer was installed.
Trip Odometer
Your trip odometer tells you how far you have driven
since you last reset it. Your vehicle is equipped with two
trip odometers, ªAº and ªBº.
Press the TRIP A/B button to change which trip odometer
is displayed.
Press the TRIP RESET button to reset the trip odometer
that is currently being displayed.