service reset Oldsmobile Aurora 2001 Owner's Manuals

2-70
CAUTION:
Your brake system may not be working properly
if the brake system warning light is on. Driving
with the brake system warning light on can lead
to an accident. If the light is still on after you've
pulled off the road and stopped carefully, have
the vehicle towed for service.
When the ignition is on, the brake system warning light
will also come on when you set your parking brake. The
light will stay on if your parking brake doesn't release
fully. If you try to drive off with the parking brake set,
a chime will also come on until you release the parking
brake. If the light stays on after your parking brake is
fully released, it means you have a brake problem.
A PARK BRAKE SET message will be displayed on
the Driver Information Center (DIC) while the park
brake is set and the vehicle is moving. The message
will not come on if the transaxle is in PARK (P).
Anti-Lock Brake System Warning Light
With the anti-lock brake
system, the light(s) will
come on when you start
your engine and may stay
on for several seconds.
That's normal.
If the light stays on, turn the ignition to OFF. Or, if
the light comes on when you're driving, stop as soon as
possible and turn the ignition off. Then start the engine
again to reset the system. If the light still stays on, or
comes on again while you're driving, your vehicle needs
service. If the regular brake system warning light isn't
on, you still have brakes, but you don't have anti
-lock
brakes. If the regular brake system warning light is also
on, you don't have anti
-lock brakes and there's a
problem with your regular brakes. See ªBrake System
Warning Lightº earlier in this section.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to RUN. If the
light doesn't come on then, have it fixed so it will be
ready to warn you if there is a problem.

2-90 DIC Warnings and Messages
Other messages or warnings may appear in the DIC
display. For Canadian drivers, in addition to the DIC
message your DIC will display EXP with a number after
it which reflects the following messages:
EXP (Export ID) Warning Message. . . . . . . . . . . .
1 AIR BAG PROBLEM. . . . . . . . . . . . . . . . . . . . . .
2 CHANGE OIL NOW. . . . . . . . . . . . . . . . . . . . . . .
3 CHANGE OIL SOON. . . . . . . . . . . . . . . . . . . . . .
4 CHECK CHARGE SYSTEM. . . . . . . . . . . . . . . . .
5 CHECK OIL LEVEL. . . . . . . . . . . . . . . . . . . . . . .
6 TRANS HOT...IDLE ENG. . . . . . . . . . . . . . . . . . .
7 CONFIRM TIME & DATE. . . . . . . . . . . . . . . . . .
8 DRIVERS DOOR AJAR. . . . . . . . . . . . . . . . . . . .
9 ENGINE HOT...A/C OFF. . . . . . . . . . . . . . . . . . .
10 HOT...REDUCE ENG RPM. . . . . . . . . . . . . . . . .
11 HOT...STOP ENGINE *. . . . . . . . . . . . . . . . . . . .
12 THEFT SYSTEM FAULT. . . . . . . . . . . . . . . . . .
13 LEFT REAR DOOR AJAR. . . . . . . . . . . . . . . . .
14 LOW BRAKE FLUID *. . . . . . . . . . . . . . . . . . . .
15 LOW ENGINE COOLANT. . . . . . . . . . . . . . . . .
16 LOW FUEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 LOW OIL PRESSURE *. . . . . . . . . . . . . . . . . . .
18 LOW TIRE PRESSURE. . . . . . . . . . . . . . . . . . .
19 LOW WASHER FLUID. . . . . . . . . . . . . . . . . . . .
20 PARK BRAKE SET *. . . . . . . . . . . . . . . . . . . . .
21 PASSENGER DOOR AJAR. . . . . . . . . . . . . . . .
22 RIGHT REAR DOOR AJAR. . . . . . . . . . . . . . . .
23 SERVICE VEHICLE SOON. . . . . . . . . . . . . . . .
24 TURN SIGNAL ON?. . . . . . . . . . . . . . . . . . . . . .
25 THEFT ATTEMPTED. . . . . . . . . . . . . . . . . . . . .
26 SERV STABILITY SYS. . . . . . . . . . . . . . . . . . . .
27 HEADLAMPS SUGGESTED. . . . . . . . . . . . . . .
28 TRUNK AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
29 BATTERY SAVER ACTIVE. . . . . . . . . . . . . . . .
32 HOT...IDLE ENGINE. . . . . . . . . . . . . . . . . . . . .
33 STARTING DISABLED *. . . . . . . . . . . . . . . . . .
36 CHECK GAS CAP. . . . . . . . . . . . . . . . . . . . . . . .
42 STABILITY ACTIVE. . . . . . . . . . . . . . . . . . . . .
The EXP codes are used to make translation from
English to other languages easier.
Pressing the RESET button will remove the above
messages or warnings from the DIC display, unless
noted by an asterisk (*).

2-91
CHECK OIL LEVEL - 5: If you ever see the
CHECK OIL LEVEL message, it indicates that the
engine oil level is 1 to 1 1/2 quarts (0.9 L to 1.4 L) low.
The message will appear only if the engine is running
and it has been at least eight minutes since the engine
was last running. If the message appears, check the oil
dipstick level. If it reads low, your oil level should be
brought up to the proper level (see ªEngine Oilº in
the Index). After bringing the oil to the proper level,
the ignition must be off for eight minutes to allow the
majority of oil to drain into the oil pan.
SERV STABILITY SYS
- 26 : If you ever see the
SERV STABILITY SYS message, it means there
may be a problem with your stability enhancement
system. If you see this message, try to reset the system
(stop; turn off the engine; then start the engine again).
If the SERV STABILITY SYS message still comes on,
it means there is a problem. You should see your dealer
for service. Reduce your speed and drive accordingly.STABILITY ACTIVE
- 42 : You may see the
STABILITY ACTIVE message on the Driver
Information Center. It means that an advanced,
computer
-controlled system has come on to help
your vehicle continue to go in the direction in which
you're steering. This stability enhancement system
activates when the computer senses that your vehicle is
just starting to spin, as it might if you hit a patch of ice
or other slippery spot on the road. When the system is
on, you may hear a noise or feel a vibration in the brake
pedal. This is normal.
When the STABILITY ACTIVE message is on,
you should continue to steer in the direction you want
to go. The system is designed to help you in bad
weather or other difficult driving situations by making
the most of whatever road conditions will permit. If the
STABILITY ACTIVE message comes on, you'll know
that something has caused your vehicle to start to spin,
so you should consider slowing down.

3-27
After you clean the player, press and hold EJECT for
five seconds to reset the CLEAN PLAYR indicator.
The radio will display CLEANED to show the indicator
was reset.
Cassettes are subject to wear and the sound quality
may degrade over time. Always make sure the cassette
tape is in good condition before you have your tape
player serviced.
Care of Your Compact Discs
Handle discs carefully. Store them in their original cases
or other protective cases and away from direct sunlight
and dust. If the surface of a disc is soiled, dampen a
clean, soft cloth in a mild, neutral detergent solution
and clean it, wiping from the center to the edge.
Be sure never to touch the signal surface when handling
discs. Pick up discs by grasping the outer edges or the
edge of the hole and the outer edge.
Care of Your Compact Disc Player
The use of CD lens cleaner discs is not advised, due to
the risk of contaminating the lens of the CD optics with
lubricants internal to the CD mechanism.
Diversity Antenna System
Your AM-FM antennas are located in the front
windshield and rear window. Be sure that the inside
surfaces of the front windshield and rear window are
not scratched and that the lines on the glass are not
damaged. If the inside surfaces are damaged, they
could interfere with radio reception. Also, for proper
radio reception, the antenna connector at the top
-center
of the front windshield and the antenna connector at
the top
-center of the rear window need to be properly
attached to the posts on the glass.
NOTICE:
Do not try to clear frost or other material from
the inside of the rear window with a razor blade
or anything else that is sharp. This may damage
the rear defogger grid and affect your radio's
ability to pick up stations clearly. The repairs
wouldn't be covered by your warranty.

5-9
NOTICE:
Use the proper towing equipment to avoid
damage to the bumper, fascia or fog lamp areas
of the vehicle.
With current trends in automotive styles and design,
it is essential that the correct towing equipment is used
to tow a vehicle. Your vehicle can be towed with
wheel
-lift or car-carrier equipment only.
Consult your dealer or a professional towing service if
you need to have your vehicle towed. See ªRoadside
Assistanceº in the Index.
Engine Overheating
You will find a coolant temperature gage on your
vehicle's instrument panel. Your driver information center
will also display messages about engine overheating.
See ªEngine Coolant Temperature Gageº in the Index.
Overheated Engine Protection
Operating Mode
Should an overheated engine condition exist and the
message HOT STOP ENGINE is displayed, an overheat
protection mode which alternates firing groups of
cylinders helps prevent engine damage. In this mode,
you will notice a loss in power and engine performance.
This operating mode allows your vehicle to be driven
to a safe place in an emergency; you may drive up to
50 miles (80 km). Towing a trailer in the overheat
protection mode should be avoided.
NOTICE:
After driving in the overheated engine protection
operating mode, to avoid engine damage, allow the
engine to cool before attempting any repair. The
engine oil will be severely degraded. Repair the
cause of coolant loss, change the oil and reset the
oil life indicator. See ªEngine Oilº in the Index.

6-50 Check Tire Pressure System
The check tire pressure system can alert you to a large
change in the pressure of one tire. The system won't
alert you before you drive that a tire is low or flat.
You must begin driving before the system will
work properly.
The LOW TIRE PRESSURE message will appear
on the Driver Information Center (DIC) if pressure
difference (low pressure) is detected in one tire.
The check tire pressure system may not alert you if:

more than one tire is low,

the vehicle is moving faster than 65 mph (105 km/h),

the system is not yet calibrated,

the tire treadwear is uneven,

the compact spare tire is installed,

tire chains are being used, or

the vehicle is being driven on a rough or frozen road.
If the anti
-lock brake system warning light comes on, the
check tire pressure system may not be working properly.
See your dealer for service. Also, see ªAnti
-Lock Brake
System Warning Lightº in the Index.The check tire pressure system detects differences
in tire rotation speeds that are caused by changes in
tire pressure. The system can alert you about a low
tire
-- but it doesn't replace normal tire maintenance.
See ªTiresº in the Index.
When the LOW TIRE PRESSURE message appears on
the Driver Information Center, you should stop as soon
as you can and check all your tires for damage. If a tire
is flat, see ªIf a Tire Goes Flatº in the Index. Also check
the tire pressure in all four tires as soon as you can. See
ªInflation
-Tire Pressureº in the Index.
Any time you adjust a tire's pressure or have one or
more tires repaired or replaced, you'll need to reset
(calibrate) the check tire pressure system. You'll also
need to reset the system whenever you rotate the tires,
buy new tires, install or remove the compact spare, and
whenever the vehicle's battery has been disconnected.
Don't reset the check tire pressure system without first
correcting the cause of the problem and checking and
adjusting the pressure in all four tires. If you reset the
system when the tire pressures are incorrect, the check
tire pressure system will not work properly and may not
alert you when a tire is low or high.

6-51
To reset (calibrate) the system:
1. Turn the ignition switch to RUN.
2. Press the SELECT right arrow button on the DIC
until you enter the GAGE mode. Then press the
SELECT down arrow until TIRE PRESSURE
appears on the display.
3. Press and hold the DIC RESET button for about
five seconds. After five seconds, the display will
show TIRE PRESSURE RESET. If TIRE
PRESSURE RESET does not appear on the display
after about five seconds, see your dealer for service.
After you release the DIC RESET button, TIRE
PRESSURE NORMAL will appear on the display.
The system completes the calibration process during
driving. Calibration time can take 45 to 90 minutes,
depending on your driving habits. After the system has
been calibrated, the system will alert the driver that a tire
is low, up to a maximum speed of 65 mph (105 km/h).Tire Inspection and Rotation
Tires should be rotated every 6,000 to 8,000 miles
(10 000 to 13 000 km). Any time you notice unusual
wear, rotate your tires as soon as possible and check
wheel alignment. Also check for damaged tires or
wheels. See ªWhen It's Time for New Tiresº and
ªWheel Replacementº later in this section for
more information.
The purpose of regular rotation is to achieve more uniform
wear for all tires on the vehicle. The first rotation is the
most important. See ªScheduled Maintenance Servicesº in
the Index for scheduled rotation intervals.
When rotating your tires, always use the correct rotation
pattern shown here.

Scheduled Maintenance
7-6Engine Oil Scheduled Maintenance
Change engine oil and filter as indicated by the GM
Oil Life System
(or every 12 months, whichever
occurs first). Reset the indicator. The system will
show you when to change the oil
-- usually between
3,000 miles (5 000 km) and 10,000 miles (16 000 km)
since your last oil change. Under severe conditions, the
indicator may come on before 3,000 miles (5 000 km).
Never drive your vehicle more than 10,000 miles
(16 000 km) or 12 months without an oil and
filter change.The system won't detect dust in the oil. So if you drive
in a dusty area, be sure to change your oil and filter
every 3,000 miles (5 000 km) or sooner if the CHANGE
OIL SOON or the CHANGE OIL NOW message
appears. Remember to reset the Oil Life System when
the oil and filter have been changed. See ªOil Life
Systemº in the Index for information on resetting.
An Emission Control Service.