instrument cluster OLDSMOBILE AURORA 2002 Owners Manual

2-23
ACC (Accessory): This position lets you use your
electrical accessories such as power windows, power
sunroof (option), radio and the windshield wipers.
ON: This is the position the switch returns to after
you start your engine and release the switch. This is the
position for normal driving. Even when the engine is not
running, you can use ON to operate your electrical
accessories and to display some instrument panel
warning lights.
START: This position starts your engine. When the
engine starts, release the key. The ignition switch will
return to ON for normal driving.Key Reminder Warning
If you leave your key in the OFF ignition position,
you will hear a warning chime when you open the
driver's door.
Always leave your key in OFF. If you leave it in any
other position, you will drain the battery power.
Retained Accessory Power (RAP)
After you turn the ignition off and remove the key, you
will still have power to accessories such as the power
windows, audio steering wheel controls, clock, sunroof
(option), accessory power outlet and the radio for up to
10 minutes. The instrument panel cluster lights will stay
on for a few seconds, then go out. Once you open a
door, the power will shut off.
ProCarManuals.com

2-35
Turn Signal/Multifunction Lever
The lever on the left side of the steering column
includes the following:

Turn and Lane
-Change Signals

Headlamp High/Low
-Beam Changer

Flash
-To-Pass Feature
For information on exterior lamps, see ªExterior
Lampsº later in this section.
Turn and Lane-Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow
you to signal either a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever will
return automatically.
An arrow on the instrument
panel cluster will flash in
the direction of the turn
or lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.
ProCarManuals.com

2-36
As you signal a turn or a lane change, if the arrows flash
very fast, a bulb may be burned out and other drivers
won't see your turn signal.
If a bulb is burned out, replace it to help avoid
an accident.
If the arrows don't go on at all when you signal a turn,
check the fuse (see ªFuses and Circuit Breakersº in
the Index) and check for burned
-out bulbs.
Turn Signal On Chime
If your turn signal is left on for more than 0.8 miles
(1.3 km), a chime will sound at each flash of the turn
signal and the DIC will display the TURN SIGNAL
ON? reminder message. To turn off the chime and
message, move the turn signal lever to the off position.
To turn off the DIC message while the turn signal is
still active, press any button on the DIC. See
ªDriver Information Center (DIC)º in the
Index for more information.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high, push
the lever away from you until you hear a click. Then
release it.
When the high beams
are on, this light on the
instrument panel cluster
will also be on.
If the fog lamps are on when you turn on the
high
-beam headlamps, the fog lamps will turn off.
The fog lamps will turn back on when you turn
off the high
-beam headlamps.
ProCarManuals.com

2-37 Flash-to-Pass Feature
This feature lets you use your high-beam headlamps
to signal a driver in front of you that you want to pass.
It works even if your headlamps are off.
To use it, pull the turn signal lever toward you.
Your high
-beam headlamps will turn on. They'll stay on
as long as you hold the lever there. Release the lever to
turn them off.
If your headlamps are on, and on high beam, your
headlamps will switch to low beam when the lever is
released. To get back to high beam, push the lever
away from you.
Windshield Wipers
The lever on the right side of your steering column
operates your windshield wipers.
If your windshield wipers are on for more than six
seconds while you are driving, the low
-beam
headlamps, instrument panel cluster backlighting and
the taillamps will turn on. For more information see
ªWiper
-Activated Headlampsº in the Index.
ProCarManuals.com

2-41
1. Push the cruise control switch, located on the right
side of the steering column at the end of the lever,
in to ON.
2. Get up to the speed you want.
3. Push the lever down to SET
-CST (Coast) and release
it. The CRUISE light on the instrument panel cluster
will come on.
4. Take your foot off the accelerator pedal.Resuming a Set Speed
Setting the cruise control at a desired speed and then
applying the brake will end the cruise control function.
Once you're going about 25 mph (40 km/h) or more,
you can briefly push the cruise control lever up to
RES
-ACC (Resume-Accelerate) to reset. This returns
you to the desired preset speed.
Remember, if you hold the lever up at RES
-ACC,
the vehicle will accelerate until you release the lever or
apply the brake. So unless you want to go faster, don't
hold the lever at RES
-ACC.
Increasing Speed While Using Cruise Control
There are three ways to go to a higher speed:

Use the accelerator pedal to go to a higher speed. Push
the lever down, then release the lever and the accelerator
pedal. You'll now cruise at the higher speed.

Move the cruise lever up to RES
-ACC. Hold it there until
you reach a desired speed and then release the lever.

To increase your speed in very small amounts, move
the lever up to RES
-ACC briefly and then release it.
Each time you do this, your vehicle will go about
1 mph (1.6 km/h) faster.
The accelerate feature will only work after you have set the
cruise control speed by pushing the lever down to SET
-CST.
ProCarManuals.com

2-44
Wiper-Activated Headlamps
This feature turns on the low
-beam headlamps,
instrument panel cluster backlighting and taillamps
after the windshield wipers have been in use for
approximately six seconds. To operate, the exterior
lamps control must be in AUTO and it must be dark
enough outside.
When the exterior lamps control is in OFF or the
parking lamp position and the windshield wiper control
is on (LO, HI or INT), the HEADLAMPS
SUGGESTED message will appear on the DIC.
When you turn the key to OFF, the wiper
-activated
headlamps will immediately turn off. The
wiper
-activated headlamps will also turn off if
you turn the exterior lamps control to OFF or
turn off the windshield wipers.
Lamps on Reminder
If the exterior lamps control is left on, you'll hear a
warning chime when you turn the ignition off, remove
the key from the ignition and open the driver's door.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset. Fully
functional daytime running lamps are required on all
vehicles first sold in Canada.
A light sensor on top of the instrument panel makes the
DRL work, so be sure it isn't covered.
The DRL system will make your high
-beam headlamps
come on at reduced brightness in daylight when the
following conditions are met:

The ignition is on,

the exterior lamps control is off, and

the transaxle is not in PARK (P).
When the DRL are on, only your high
-beam headlamps
will be on. The parking lamps, taillamps, sidemarker
and other lamps won't be on.
ProCarManuals.com

2-47
Interior Lamps
Instrument Panel Brightness Knob
This feature controls the brightness of the instrument
panel lights.
The knob for this feature is
located on the driver's side
of the instrument panel.
Turn the knob clockwise to brighten the instrument
panel cluster lights and displays. Turn the knob
counterclockwise to dim the instrument panel cluster
lights and displays.
If it is day and your parking lamps are on, the instrument
panel cluster lights and displays will come on at full
intensity and will not be adjustable. If it is dark enough
outside and your parking lamps are on, the instrument
panel cluster lights and displays and the backlighting for
the door switches will come on, and can also be adjusted.
Courtesy Lamps
If it is dark enough outside and the front reading lamp
slider lever, located on the overhead console, is in the
AUTO position, when any door is opened all of the
vehicles courtesy lamps will come on. See ªReading
Lampsº in the Index. They make it easier for you to
enter and leave the vehicle. The courtesy lamps will
remain on for about 25 seconds after all doors have
been closed. They will then theater dim to off.
Move the front reading lamp slider lever to ON to turn
on the interior courtesy lamps. When the control is
moved back to either OFF or AUTO, the courtesy
lamps will immediately turn off.
If the control is OFF when the doors are opened, only
the lower instrument panel courtesy lamps will come on.
Also, if the control is OFF when illuminated entry or
delayed exit lighting are active, only the lower
instrument panel courtesy lamps will be on.
If a door is left ajar, your interior lamps will turn
off after 10 minutes to save your battery.
ProCarManuals.com

2-68
Instrument Panel Cluster
Your vehicle is equipped with this instrument panel cluster, which includes indicator warning lights and gages that are
explained on the following pages. The instrument panel is designed to let you know at a glance how your vehicle is
running. You'll know how fast you're going, how much fuel you're using, and many other things you'll need to drive
safely and economically.
United States version shown, Canada similar
ProCarManuals.com

2-69 Speedometer and Odometer
Your speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (km/h). Your
odometer shows how far your vehicle has been driven,
in either miles (used in the United States) or kilometers
(used in Canada).
The speedometer shows a top speed of 140 mph
(220 km/h). This is not intended to be the vehicle's
top speed.
You may wonder what happens if your vehicle needs a
new odometer installed. If the new one can be set to the
mileage total of the old odometer, then it must be. But if
it can't, then it's set at zero and a label must be put on
the driver's door to show the old mileage reading when
the new odometer was installed.
Trip Odometer
Your trip odometer tells you how far you have driven
since you last reset it. Your vehicle is equipped with two
trip odometers, A and B. The buttons for this feature
are located to the left of the steering column. The trip
odometer displays are located in the center of the
instrument panel cluster. Press the TRIP A/B button
to change which trip odometer is displayed.
Press and hold the TRIP RESET button to reset the trip
odometer that is currently being displayed.
ProCarManuals.com

6-15
A. Engine Compartment Fuse Block
B. Windshield Washer Fluid Reservoir
C. Engine Coolant Surge Tank
D. Remote Positive (+) Battery Terminal
E. Power Steering Fluid Reservoir
F. Passenger Compartment Air Filter
G. Remote Negative (
-) Terminal
H. Engine Oil Fill Cap
I. Engine Oil Dipstick
J. Brake Fluid Reservoir
K. Automatic Transaxle Fluid Dipstick
(near the air cleaner)
L. Engine Air Cleaner/Filter
Engine Oil
If the CHECK OIL LEVEL message appears on the
instrument cluster, it means you need to check your
engine oil level right away. For more information, see
ªDIC Warnings and Messagesº in the Index.
You should check your engine oil level regularly; this is
an added reminder.
ProCarManuals.com