ignition Oldsmobile Cutlass Supreme 1996 s User Guide

4
Move the lever up as far as it will go.
3. Move the ignition key to the LOCK position.
4. Remove the key and take it with you. If you can
leave your vehicle with the ignition key in your
hand, your vehicle
is in PARK (P).
Console Shift
1. Hold the brake pedal down with your right foot and
2. Move the shift lever into the PARK (P) position
set the parking brake.
like this: Hold in the button
on the
lever, and push the lever all
the way toward the front of
your vehicle.
3. Move the ignition key to the LOCK position.
4. Remove the key and take it with you. If you can
leave your vehicle with the ignition key in your
hand, your vehicle is in PARK
(P).
2-20

Shifting Out of PARK (P)
Your Oldsmobile has a brake-transaxle shift interlock.
You
.must fully apply your regular brakes before you can
shift
from PARK (P) when the ignition is in the‘RUN
position. See “Automatic Transaxle Operation” in
the Index.
If you cannot shift out of PARK
(P), ease pressure on
the shift lever by pushing it all the way into PARK (P),
while keeping the brake pedal pushed down. Release the
shift
leyer button if you have a console shift. Then move
the shift lever out of PARK (P), being sure to press the
shift lever button if you have a console shift.
If you ever hold the brake pedal down but still can’t,
shift out of PARK
(P), try this:
1. Turn the key to the OFF position.
2. Apply and hold the brake until the end of Step 4.
3. Shift to NEUTRAL (N).
4. Start the engine and shift to the drive gear you want.
5. Have the vehicle fixed as soon as you can.
Parking Over Things That Burn
Things that can burn could touch hot exhaust
parts under your vehicle and ignite. Don’t park
over papers, leaves, dry grass
or other things that
can burn.
2-22

Power Windows
It can be dangerous to get out of your vehkle if
the shift lever
is not fully in PARK (P) with the’
parking. brake firmly,set. Your vehicle can roll.
Don’t leave your vehicle wlqen the.engi.ne
is , ’
running unless you have to. If you’ve left the . ’
engine running, the vehicle can move suddenly. ”
You or‘others could be injured. .To be sure.your ,.
.vehicle won’t move, even when you’re on fairly
level’ground, always set your parking brake and
move the shift lever to
PARK (P).
Follow the proper steps to be sure your vehicle won’t ,
move. See “Shifting Into PARK (P)” in the Index,.
If you are parking on a hill and if you’re pulling a
trailer,
also see. “Towing a Trailer” in the Index. .
!
Switches on the driver’s door armrest control each of the
windows when the ignition
is on. In addition, each
passenger door has a’switch for its own window.
rhe driver’s window switch has an auto-down feature.
This switch is labeled AUTO. Tap the rear of the switch,
and the’driver’s window will open
a small amount. If the
rear
of the switch is pressed all the way down, the
window will
go all the way down.

Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:
0 Push in the SET button until you reach the lower
speed you want, then release it.
To slow down in very small amounts, push the SET
button for less than half a second. Each time you do
this, you'll go
1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot
off the.peda1, your vehicle will slow
down to the cruise control speed you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills depends
upon your speed, load and the steepness
of the hil.ls.
When going up steep hills, you may have to step on the
accelerator pedal to maintain your speed. When going
downhill, you may have to brake or shift to a lower gear
to keep your speed down.
Of course, applying the brake
takes you out of cruise control. Many drivers find this to
be too much trouble and don't use cruise control on
steep hills.
.Ending Cruise Control
There are two ways to turn off the cruise control:
Step lightly on the brake pedal; OR
Move the cruise switch to OFF.
Erasing Cruise Speed Memory
When you turn off the cruise control or the ignition, or
shift into PARK
(P) or NEUTRAL (N), your cruise
control set speed memory is erased.

Lamps
r.
The lamp controls are on the instrument panel. They
control these systems:
.
0 Headlamps
Taillamps
Parking Lamps
License Lamps
Sidemarker Lamps
Instrument Panel Lights
0 Courtesy Lamps
Fog Lamps
2Q.. , Turn the knob to this symbol (B) to turn the
headlamps and other operating lamps.
PC Turn the knob to this symbol (A) to turn on
the parking and other operating lamps without
the headlamp s .
Turn the knob to OFF to turn off the lamps.
A warning chime will sound when you,.turn the ignition
switch to the OF", LOCK or ACC position with the
lamps on.
Daytime Running Lamps
Daytime Running Lamps (DIU) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work,
so be sure it isn't covered.

The DRL system will make your low-beam headlamps
come on at a reduced brightness when:
0 The ignition is on,
0 The headlamp switch is off, and
0 The parking brake is released.
When the DRL are on, only your low-beam headlamp,s
will be on. The taillamps, sidemarker and other lamps
won’t be on. Your instrument panel won’t be lit
up either.
When it’s dark enough outside, your low-beam
headlamps will change to full brightness. The other
lamps that come on with your headlamps will also
come on.
When it’s bright enough outside, the regular lamps will
go out, and your low-beam headlamps will change
to
-the reduced brightness of DIU.
To idle your vehicle with the DRL
off, set the parking
brake while the ignition is in the
OW or LOCK
position. Then start your vehicle. The DRL will stay off
until you release the parking brake.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
Fog Lamps
To turn fog lamps on, press the top of the switch (C). Press the
bottom of the switch to
turn the fog lamps off. Your parking
lamps must be on, or your fog lamps won’t come on.
The fog lamps will go
off whenever you change to
high-beam headlamps. When you return to low beams,
the fog lamps will come
on again.
Interior Lamps
Instrument Panel Brightness Control
You can brighten or dim the instrument panel lights by
moving the instrument panel lights dial.
If you turn the
dial all the way to
INT, your courtesy or interior lamps
will come on.
Courtesy Lamps
When any door is opened, several larnps come on. These
lamps are courtesy lamps. They make it easy for you to
enter and leave your vehicle. You can
also turn these
lamps on by moving the dial near the beadlamp knob all
the way up to
INT.
Some of the lamps have switches so you can turn them
on, even when the doors are closed. These lamps are
reading lamps.
To avoid draining your battery, be sure to ’
turn off all reading lamps when leaving your vehicle.
2-33

$7 m the glass panel and sunsh,ade, press the rem df
I the switch. Let go of the switch to stop the panel in any ' .
position. Press the front of the switch to close the glass
panel.. .The sunshade
can only be closed by hand. -. . ,: ',
Your sunroof includes a sliding glass panel .anda
sliding, sunshade. The switch works ,only when ,the
ignition is
,Theamroof glash panel cannot be opened or closed $-.;
your vehicle'has an electrkal failure%-., , . . -, .- :: . , I' ,_ i , . ;,
I :. .; -L.

Air Bag Readiness Light
There is an air bag readiness light on the instrument
panel, which. shows AIR BAG or the air bag symbol.
The system checks the air bag’s electrical system for
malfunctions. The light tells you if there is an electrical
problem. The system check includes the air bag sensors,
the air bag modules, the wiring and the crash sensing
and diagnostic module. For more information on
the air
! bag system, see “Air Bag” in the Index.
You will see this light flash
for a few seconds when you
turn your ignition to RUN or START. Then the light
should go out. This means
the system is ready.
If the air bag readiness light doesn’t come on when you
start your vehicle, or stays
on, or comes on when you
are driving, your air bag system may not work properly.
Have your vehicle serviced right away.
Charging ‘System Light
The charging system light
will come on briefly when
you turn on the ignition, as
a check to show you it’s
working. Then it should
go out.
.If it stays on, or comes on while you are driving,
you
may have a problem with the charging system. It could
indicate that you have a loose drive belt or another
electrical problem. Have it checked right away. Driving
while this light is on could drain your battery.
If you must drive a short distance with the light on, be
certain to turn off all your accessories, such as the radio
and air conditioner.

Brake System Warning Light
Your Oldsmobile’s hydraulic brake system is divided
into two parts. If one part isn’t working, the other part
can still work and stop you. For good braking, though,
~ you need both parts workmg well.
If the warning light comes on, there could be
a brake
problem. Have your brake system inspected right away.
BRAKE
This light should come on
briefly when you turn the
ignition key to
RUN. If it
doesn’t come on then,
have
it fixed so it will be
ready to warn you if
there’s a problem.
If the light comes on while you
are driving, pull off the
road and stop carefully. You may notice that the pedal is
harder to push.
Or, the pedal may go closer to the floor.
It may take longer to stop. If the light is still on, or if the anti-lock brake system warning light
is flashing, have
the vehicle towed for service. (See “Anti-Lock Brake
System Warning Light” and “Towing Your Vehicle” in
the Index
.)
1 C.’ UTION:
Your brake system may not be working properly
if the brake system warning light is on. Driving
with the brake system warning light on can lead
to an accident. If the light is still on or if the
anti-lock brake system warning light is flashing
after you’ve pulled
off the road and stopped
carefully, have the vehicle towed for service.
When the ignition is on, the brake system warning light
will also come on when
you set your parking brake. The
light will stay on if your parking brake doesn’t release
fully. If it stays on after your parking brake is fully
released, it means you have a brake problem.
2-47

Anti-Lock Brake System Warning Light
With the anti-lock brake system, this light will come
on when you start your
engine and it will stay
on for three seconds.
That’s normal.
If the light flashes when you’re driving, you don’t have
anti-lock brakes and there could be
a problem with your
regular brakes. Pull
off the road and stop carefully. You
may notice that the pedal is harder to push. Or, the pedal
may go closer to the floor. It may take longer to stop.
Vehicle” in the Index.)
, Have the .vehicle towed for service. (See.“Towing Your
Your regular brake system may not be working
properly
if the anti-lock brake system warning
light is flashing. Driving with the anti-lock brake system warning light flashing can lead to an
accident. After you’ve pulled
off the road and
stopped carefully, have the vehicle towed
for service.
If the anti-lock brake system warning light stays on
longer than normal after you’ve started your engine, turn
the ignition
off. Or, if the light comes on and stays on
when you’re driving, stop as soon as possible and turn
the ignition
off. Then start the engine again to reset the
system. If the light still stays on, or comes on again
while you’re driving, your Oldsmobile needs service. If
the light is on but not flashing and the regular brake
system warning light isn’t on, you still have brakes, but
you don’t have anti-lock brakes.
The anti-lock brake system warning light should come
on briefly when you turn the ignition key to
RUN. If the
light doesn’t come on then, have it fixed
so it will be
ready
to warn you if there is a problem.
2-48