reset OLDSMOBILE INTRIGUE 1998 Owners Manual

Windshield Washer At the end of the right-hand lever on the steering wheel,
there
is a wiper symbol. To spray washer fluid on the
windshield, push the button
on the end of the lever. The
wipers will run
for several sweeps and then either stop
or return to your preset speed.
I-
CAUTION:
In freezing weather, don’t use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
2-34
ProCarManuals.com

3. Push the COAST/SET
button on your steering wheel and release it. Once
you’re going about
25 rnph (40 km/h)or more,
press the RES/ACCEL
button on your steering
wheel. You’ll go right back
up to your chosen speed and
stay there.
4. Take your foot off the accelerator.
The CRUISE light on the instrument panel cluster will
come on after the cruise control has been set to the
desired speed.
It will go off when you:
step lightly on the brake pedal,
0 press CLEAR on the steering wheel or
0 press the CRUISE button on the instrument panel.
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course shuts off
the cruise control. But you don’t need to reset
it.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:
0
0
Use the accelerator pedal to get to the higher speed.
Press the COAST/SET button on the steering wheel,
then release the button and the accelerator pedal.
You’ll now cruise at the higher speed.
Press the RES/ACCEL button on the steering wheel.
Hold it there until you get up to the speed you want
and then release the switch. (To increase your speed
in very small amounts, press the RES/ACCEL
button for less than half a second and then release it.
Each time you do this, your vehicle will
go 1 mph
(1.6 km/h) faster.)
2-36
ProCarManuals.com

Speedometer/Odometer
Your speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (kndh). Your
odometer shows how far your vehicle has been driven in
either miles (used in the United States) or in kilometers
(used in Canada).
Your vehicle has a tamper-resistant odometer.
If your odometer fails and needs to be replaced, the
entire cluster needs to be replaced. Take your vehicle to
the dealer to have this done. The dealer will have the
new cluster odometer set to the mileage of the old
odometer/cluster if at all possible. But if it can’t, then
it’s set at zero and a label must be put on the driver’s
door to show the old mileage reading when the new
odometer was installed.
SeasodTrip Mode
Press this button to display
It is also pressed to display the trip mileage (trip mode).
The mode switch is located
on the left side of the
instrument panel, next to the TRIP RESET button for
the trip odometer.
2-53
ProCarManuals.com

Trip Odometer
Your trip odometer (trip mode) tells you how far you
have driven since you last reset it. To set it to zero, press
the
TRIP RESET button on the left side of the
instrument panel.
Tachometer
The tachometer displays the engine speed in thousands
of revolutions per minute (rpm).
NOTICE: I
Do not operate the engine with the tachometer in
the red area, or engine damage may
occur.
2-54
ProCarManuals.com

If the CHANGE OIL light comes on and stays on after
you
start the engine, have the oil changed. The light may
indicate to change the oil sooner than suggested in your
maintenance schedule, depending on your driving patterns.
This light will come on when the system predicts that the
oil’s remaining useful life is almost up. It alerts you to
change the oil on a schedule consistent with your vehicle’s \
driving conditions. Therefore,
you should change your oil
at the intervals recommended in your maintenance
schedule or when the CHANGE
OIL light comes on,
whichever comes first. See “Engine Oil, When to Change”
and “Maintenance Schedule,” in the Index.
To reset the CHANGE
OIL light, see “Engine Oil” in
the Index.
Fuel Gr 2
0
Your fuel gage tells you
about how much fuel
you
have left when the ignition
is on. When the indicator
nears EMPTY
(E), you still
have a little fuel left,
but
you should get more soon.
Here are some things owners ask about. All these
situations are normal and do not show
a problem with
your fuel gage:
At the service station, the pump shuts off before the
gage reads
FULL (F).
It takes a little more or less fuel to fill up than the gage
indicated.
For example, the gage may have indicated
the tank was half full, but it actually took a little more
or less than half
the tank’s capacity to fill it.
The gage moves a little when you turn the corner or
speed
up.
2-65
ProCarManuals.com

PUSHBUTTONS: The five numbered pushbuttons let
you return to your favorite stations.
You can set up to
15 stations (five AM, five FMl and five FM2). Just:
1. Turn the radio on.
2. Press AM-FM to select the band.
3. Tune in the desired station.
4. Press TONE to select the equalization that best suits
the type
of station selected.
5. Press and hold one of the five numbered buttons.
The sound will mute. When
it returns, release the
button. Whenever you press that numbered button,
the station you set will return and the tone that you
selected will also be automatically selected for
that button.
6. Repeat the steps for each pushbutton.
P SCAN: Press SCAN for more than two seconds, and
P SCAN will appear on the display. The radio will go to
the first preset station stored on your pushbuttons, stop
for a few seconds, then go on
to the next preset station.
Press SCAN again
to stop scanning.
Setting the Tone
BASS: Press this knob lightly so it extends. Turn the
knob to increase or decrease bass. When you use this
control,
the radio’s tone setting will switch to manual.
TREB: Press this knob lightly so it extends. Then pull
the knob all the way out. Turn the knob to increase or
decrease treble. When you use this control, the radio’s
tone setting will switch to manual. If a station is weak or
noisy, you may want
to decrease the treble.
Push these knobs back into their stored positions when
you’re not using them.
TONE: This feature allows you to choose preset bass
and treble equalization settings designed for jazz, vocal,
pop, rock and classical stations. JAZZ will appear on the
display when you first press TONE. Each time you press
it, another setting will appear
on the display. Press it
again after CLASSIC appears and MANUAL will
appear. Manual tone control will return to the
BASS and
TREB knobs. Also, if you use the BASS and TREB
knobs, control will return to them and MANUAL
will appear.
3-11
ProCarManuals.com

FWD (2): Press this button to advance quickly to
another part of the tape. Press the button again to return
to playing speed. The radio will play the last-selected
station while the tape advances. You may select stations
during FWD operation by using TUNE.
PROG (3): Press this button to play the other side of
the tape.
00 (4): Press this button to reduce background noise.
Note that the double-D symbol will appear on the display.
Dolby Noise Reduction is manufactured under a license
from Dolby Laboratories Licensing Corporation. Dolby
and the double-D symbol are trademarks of Dolby
Laboratories Licensing Corporation.
TONE: Press this button to select a tone while playing a
cassette. The tone will be automatically set whenever
you play a cassette tape.
SEEK: Press the up or down arrow to search for the
next or previous selection
on the tape. Your tape must
have at least three seconds
of silence between each
selection for SEEK
to work.
SCAN: Press this button to listen to each selection for a
few seconds. The tape will go to the next selection, stop
for a few seconds, then go on to
the next selection. Press this
button again to stop scanning. The sound will mute,
SCAN will appear on the display and the tape direction
arrow will blink while scanning.
AM-FM: Press this button to play the radio when a tape
is in the player. The tape will stop but remain in the player.
TAPE AUX: If you have a tape inserted and the radio is
playing, press TAPE AUX to play your tape. To return
to the radio while a tape is playing, press
AM-FM. The
inactive tape will remain safely inside the radio for
future listening.
E JECE Press this button to remove the tape. The radio
will play. EJECT may be activated with either the
ignition or radio off. Cassettes may be loaded with the
radio and ignition off if this button is pressed first.
CLN: If this message appears on the display, the
cassette tape player needs to be cleaned. It will still play
tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See “Care of
Your Cassette Tape Player” in
the Index. After you clean
the player, press and hold EJECT for five seconds to
reset the CLN indicator. The radio will display
--- to
show the indicator was reset.
3-13
ProCarManuals.com

SCAN: Press this button and release it to listen to
stations for a few seconds. The radio will go to
a station,
stop for a few seconds, then go on to the next station.
Press the button again to stop scanning. The sound will
mute while scanning, and SCAN will appear on the
display. If you press SCAN for more than two seconds,
the radio will change
to P SCAN mode. P SCAN will
appear
on the display.
PUSHBUTTONS: The five numbered pushbuttons let
you return to your favorite stations. You can set up to
15 stations (five AM, five FMl and five FM2). Just:
1.
2.
3.
4.
5.
6.
Turn the radio on.
Press AM-FM to select the band.
Tune
in the desired station.
Press
TONE to select the equalization that best suits
the type of station selected. (This function is not
available on the Bose radio.)
Press and hold one of the five numbered buttons.
The sound will mute. When it returns, release the
button. Whenever you press that numbered button,
the station you set will return and the tone that you
selected will also be automatically selected for that
button. (The tone will not automatically return on the
Bose radio.)
Repeat the steps for each pushbutton.
P SCAN: Press SCAN for more than two seconds, and
P
SCAN will appear on the display. The radio will go to
the first preset station stored
on your pushbuttons, stop
for a few seconds, then go on
to the next preset station.
Press SCAN again to
stop scanning.
Setting the Tone
BASS:
Press this knob lightly so it extends. Turn the
knob to increase or decrease bass. When you use this
control, the radio’s tone setting will switch to manual.
(The radio’s tone setting will not switch to manual on
the Bose radio.)
TREB: Press this knob lightly so it extends. Then pull the
knob all the way out. Turn the knob to increase or
decrease treble. When you use this control, the radio’s tone
setting will switch to manual. (The radio’s tone setting wi\
ll
not switch to manual on the Bose radio.) If a station is
weak or noisy, you may want to decrease the treble.
Push these knobs back into their stored positions when
you’re not using them.
TONE: This feature allows you to choose preset bass and
treble equalization settings designed for
jazz, vocal, pop,
rock and classical stations.
JAZZ will appear on the
display when
you first press TONE. Each time you press
it, another setting will appear on the display. Press it
again after CLASSIC appears and
MANUAL will appear.
3-15
ProCarManuals.com

EJECT: Press this button to remove the tape. The radio
will play.
EJECT may be activated with either the
ignition or radio off. Cassettes may be loaded with the
radio and ignition off if this button
is pressed first.
CLN: If this message appears on the display, the
cassette tape player needs to be cleaned.
It will still play
tapes, but you should clean it as soon as possible to
prevent damage to the tapes and player. See “Care of
Your Cassette Tape Player” in the Index. After you clean
the player, press and hold EJECT for five seconds to
reset the CLN indicator. The radio will display
--- to
show the indicator was reset.
Playing a Compact Disc
With the ignition on, insert a disc partway into the slot,
label side up. The player will pull it in and the disc
should begin playing. If you want
to insert a CD when
the ignition is off, first press EJECT or RCL.
The
CD player will play either normal-size discs or the
smaller
8 cm discs with an adapter.
Note that when the disc is inserted, CD will be
displayed. When the disc is playing, a box will appear
around CD
on the display. If you select a tone setting for
your
CD, it will be activated each time you play a CD.
(The tone setting function is not available on the
Bose radio.) As
each new track starts to play, the track number will
appear in the display.
If
E (error) and a number appear on the radio display
and the disc comes out, it could be that:
E20: The road is too rough. The disc should play
when the road is smoother.
0 E20: The disc is dirty, scratched, wet or
upside down.
E20: The air is very humid. If so, wait about an hour
and try again.
If any error occurs repeatedly
or if an error can’t be
corrected, please contact your retailer. If your radio
displays an error number, write it down and provide
it to
your retailer when reporting the problem.
REV (1): Press and hold this button to quickly reverse
within a track.
You will hear sound at a reduced volume.
The display will show elapsed time.
FWD (2): Press and hold this button to quickly advance
within a track. You will hear sound at a reduced volume.
The display will show elapsed time.
RDM (5): Press this button to hear the tracks in random,
rather than sequential, order.
RDM will appear on the
display when you press this button.
3-18
ProCarManuals.com

Audio Steering Wheel Controls
(If Equipped)
If your vehicle has this
feature, you can control
certain radio functions
using the buttons
on your
steering wheel.
VOL: Press the up or down arrow to increase or
decrease volume.
SEEK: Press this button to tune to a higher radio
station. When playing a cassette tape or compact disc,
press
SEEK to hear the next selection. There must be
at least a three-second gap between selections on a
cassette tape.
PROG: Press this button to tune in a higher preset radio
station. When playing a cassette tape, press
PROG to
hear the other side of a tape that is playing. When using
the
CD changer, this button will seek the next selection.
Understanding Radio Reception
AM
The range for most AM stations is greater than for FM,
especially at night. The longer range, however, can
cause stations to interfere with each other. AM can pick
up noise from things like storms and power lines.
Try
reducing the treble to reduce this noise if you ever get it.
FM Stereo
FM stereo will give you the best sound, but FM signals
will reach only about 10 to
40 miles (16 to 65 km). Tall
buildings
or hills can interfere with FM signals, causing
the sound to come and
go.
3-25
ProCarManuals.com