Oldsmobile Intrigue 2000 s Manual PDF

2-3
Your vehicle comes with two master keys and one spare
key. The master key can be used for the ignition, as well
as all door locks, trunk and storage compartments.
The third key is provided as a spare key.
These keys don't have key plugs. Your Oldsmobile
dealer or Roadside Assistance has a code for your key.If you need a new master key, contact your dealer who
can obtain the correct key code or, in an emergency, call
Oldsmobile Roadside Assistance at 1
-800-442-OLDS
(6537) (In Canada call 1
-800-268-6800).
NOTICE:
Your vehicle has a number of features that can
help prevent theft. But you can have a lot of
trouble getting into your vehicle if you ever lock
your key inside. You may have to damage your
vehicle to get in. So be sure you have an
extra key.

2-4
Door Locks
CAUTION:
Unlocked doors can be dangerous.
Passengers -- especially children -- can easily
open the doors and fall out. When a door is
locked, the inside handle won't open it.
Outsiders can easily enter through an unlocked
door when you slow down or stop your vehicle.
This may not be so obvious: You increase the
chance of being thrown out of the vehicle in a
crash if the doors aren't locked. Wear safety belts
properly, lock your doors, and you will be far
better off whenever you drive your vehicle.
There are several ways to lock and unlock your vehicle.
From the outside, use your key or keyless entry
transmitter, if equipped.
Power Door Locks
Press the power door lock
switch located on the door
near the handle to lock or
unlock all doors.

2-5
The rear doors do not have power door lock switches.
The manual lever on each front and rear door works
only on that door's lock. It won't lock or unlock all the
doors. Push the manual lever rearward to unlock and
forward to lock.
Last Door Closed Locking
This feature allows the doors to be locked while the
passengers are leaving the vehicle. This also provides a
brief time period after all the doors are closed, but
before the doors lock, in which the doors may be
reopened. Last door closed locking can be programmed
by the owner.
Last door closed locking is activated by either the power
door lock switch inside the vehicle or by pressing
the LOCK on the remote keyless entry transmitter
(if equipped). After pressing the power door lock switch
once, three chimes will be heard. The three chimes
indicate that the last door closed locking has
been activated.
The driver has three possible options once the last door
closed locking is activated:

Cancel the last door closed locking by pressing
the unlock switch or by fully inserting the key
in the ignition.

Override the last door closed locking feature and
lock the doors immediately by pressing the lock
switch a second time.

Let the last door closed locking feature complete the
locking of the vehicle.

2-6
If the driver wishes to let the last door closed locking
feature complete the locking of the vehicle, no
additional action is required. The last door closed
locking feature will lock the doors automatically after
all the doors have been closed for a period of five
seconds. During this five second period, any door may
be reopened, at which time the three possible actions
described previously are again available.
You can customize the vehicle to activate the last door
closed locking feature as described previously or to
completely disable the last door closed locking feature at
all times. If disabled, the doors will lock immediately
when a power door lock switch is pressed. The last door
closed locking feature is customized when the driver
performs the following sequence with the doors closed
and the ignition key in ON.
1. Press and hold the power door lock switch in the
unlock position.
2. While holding the door unlock switch, cycle the
transaxle out of and back into PARK (P).3. After an initial transaxle cycle, each additional cycle
will turn the last door closed locking feature on
or off.
4. During this customization procedure, the chime will
sound, providing the driver feedback. A single chime
will be heard if the last door closed locking feature is
off, and two chimes will be heard if the last door
closed locking feature is on.
5. When the door unlock switch is released, the vehicle
will remain in the most recent operating mode.
The last door closed locking feature is enabled when the
vehicle is shipped from the factory.
Disconnecting the battery for up to a year will not
change or delete the last door closed locking feature.

2-7 Programmable Automatic Door Locks
Programmable automatic door locks is a standard
feature intended to provide enhanced security and
convenience by automatically locking and unlocking
vehicle doors. The automatic locking and unlocking of
the vehicle will occur if the ignition key is in ON and
the driver's door is closed when the vehicle is shifted
out of PARK (P). One of four operating modes may be
selected and programmed by the driver:
Mode 1: No automatic door lock or unlock.
Mode 2: Automatic all door lock when transaxle is
shifted out of PARK (P). No automatic door unlock.
Mode 3: Automatic all door lock when transaxle is
shifted out of PARK (P). Automatic all door unlock
when transaxle is shifted into PARK (P).
Mode 4: Automatic all door lock when transaxle is
shifted out of PARK (P). Automatic driver's door only
unlock when transaxle is shifted into PARK (P).The operating mode of the programmable automatic
door locks will be changed when the driver performs the
following sequence with the doors closed and the
ignition key in ON.
1. Press and hold the power door lock switch in the
lock position.
2. While holding the door lock switch, cycle the
transaxle out of and back into PARK (P).
3. After an initial transaxle cycle, each additional cycle
will advance to the operating mode by one, starting
from the current operating mode.
4. During this customization procedure, the automatic
door lock and unlock functions will operate as
defined by each mode listed, providing the customer
with feedback of the current operating mode.
5. If cycled beyond Mode 4, the vehicle will enter
operating Mode 1. When the door lock switch is
released, the vehicle will remain in the most recent
operating mode.
The programmable automatic door locks are in operating
Mode 3 when the vehicle is shipped from the factory.
Disconnecting the battery for up to a year will not
change or delete any previously programmed modes.

2-8 Rear Security Locks
Your vehicle is equipped
with rear door security
locks that help prevent
passengers from opening
the rear doors of your
vehicle from the inside.
To use one of these locks:
1. Open one of the rear doors.
2. On the inside of the rear door will be a lock. Insert
your master key into this lock and turn it upward.
This will engage the safety lock.
3. Close the door.
4. Do the same thing to the other rear door.
The rear doors on your vehicle cannot be opened from the
inside when this feature is in use. If you want to open the
rear door when the security lock is on, unlock the door
from the inside and then open the door from the outside.
Lockout Prevention
Lockout Prevention is a standard feature intended to
provide enhanced security and convenience. This feature
prevents a driver who has left the key in the ignition
from locking the doors using the power door lock switch
while any door is open.
To override this feature, when the key is in the ignition
and a door is open, hold the power door lock switch for
more than three seconds.
This feature cannot guarantee that you will never be
locked out of your vehicle. If you don't leave the key in
the ignition, or if you use the manual door lock, you
could still lock your keys inside your vehicle. Always
remember to take your keys with you.

2-9
Keyless Entry System (If Equipped)
If your vehicle has this feature, you can lock and unlock
your doors or unlock your trunk from about 3 feet (1 m)
up to 30 feet (9 m) away using the remote keyless entry
transmitter supplied with your vehicle.
Your keyless entry system operates on a radio frequency
subject to Federal Communications Commission (FCC)
Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with RSS
-210 of Industry Canada.
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation of
the device.Changes or modifications to this system by other than an
authorized service facility could void authorization to
use this equipment.
At times you may notice a decrease in range. This is
normal for any remote keyless entry system. If the
transmitter does not work or if you have to stand closer
to your vehicle for the transmitter to work, try this:

Check the distance. You may be too far from your
vehicle. You may need to stand closer during rainy
or snowy weather.

Check the location. Other vehicles or objects may be
blocking the signal. Take a few steps to the left or
right, hold the transmitter higher, and try again.

Check to determine if battery replacement is
necessary. See the instructions that follow.

If you're still having trouble, see your dealer or a
qualified technician for service.

2-10 Operation
Press UNLOCK once to
unlock the driver's door and
to turn the interior lamps on
(see ªIllumination on
Remote Activationº in the
Index for more details).
Press UNLOCK again within five seconds to
unlock all doors.
To lock all doors, press LOCK. To unlock the trunk,
press the trunk symbol on the remote keyless entry
transmitter. The trunk will only unlock when the vehicle
is in PARK (P).
Remote Alarm
When you press the alarm button on the remote keyless
entry transmitter, the headlamps will flash, the horn will
sound repeatedly and the interior lamps will illuminate.This will allow you to attract attention if needed.
The alarm will continue until:

The driver presses the alarm button on the remote
keyless entry transmitter a second time,

the ignition is turned to ON or

110 seconds has elapsed.
Remote Activation Verification (RAV)
This feature helps provide audible and/or visible feedback
that a remote keyless entry lock or unlock command has
been received and executed. The ignition must be in OFF
for the remote activation verification to work.
You may select one of four operating modes for the
reception of a lock command. You may also select one
of four operating modes for the reception of an unlock
command. The selection and programming of the lock
and unlock modes are independent of each other.
The following modes are available for either lock or
unlock verification:
Mode 1: No Verification
Mode 2: Horn Chirp only
Mode 3: Headlamp and Parking Lamp Flash only
Mode 4: Horn Chirp and Headlamp and Parking
Lamp Flash

2-11
The operating mode of the remote activation verification
lock (RAV) feature will be changed when the driver
performs the following sequence with the doors closed
and the ignition key in ON:
1. Press and hold down the power door lock switch in
the lock position.
2. While holding the door lock switch, press and
release the remote keyless entry transmitter
LOCK button. This button press will initialize the
customization mode. Upon initiation of this mode,
the chime will sound the number of chimes
corresponding to the current RAV lock mode.
3. Each additional press of the remote keyless entry
transmitter LOCK button will cause the vehicle to
advance to the RAV lock mode by one, starting from
the current RAV lock mode.
4. If cycled beyond RAV lock Mode 4, the vehicle will
enter RAV lock Mode 1. When the door lock switch
is released, the vehicle will remain in the most recent
RAV lock mode.
Disconnecting the battery for up to a year will not
change or delete any previously programmed modes.Illumination on Remote Activation
This feature is included on vehicles with the remote
keyless entry system. The interior illumination will be
activated when an remote keyless entry door unlock
command is received. The ignition must be off for the
remote activation illumination to work. The interior
lamps will illuminate until the ignition is turned to
ON or until the illumination period of 40 seconds
has elapsed.
If during the illumination period, a door is opened, the
timed illumination period will be cancelled, though the
interior lamps will remain on until all doors are closed.
Matching Transmitter(s) To Your Vehicle
Each remote keyless entry transmitter is coded to
prevent another transmitter from unlocking your vehicle.
If a transmitter is lost or stolen, a replacement can be
purchased through your dealer. Remember to bring any
remaining transmitters with you when you go to your
dealer. When the dealer matches the replacement
transmitter to your vehicle, any remaining transmitters
must also be matched. Once your dealer has coded the
new transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have only four transmitters
matched to it.

2-12 Battery Replacement
Under normal use, the battery in your remote keyless
entry transmitter should last about three years.
You can tell the battery is weak if the transmitter won't
work at the normal range in any location. If you have to
get close to your vehicle before the transmitter works,
it's probably time to change the battery.
NOTICE:
When replacing the battery, use care not to touch
any of the circuitry. Static from your body
transferred to these surfaces may damage
the transmitter.
To replace your battery:
1. Insert a flat object like a dime into the slot on the
back of the transmitter. Gently pry apart the front
and back.
2. Gently pry the battery out of the transmitter.
(Do not use a metal object.)
3. Put the new battery into the transmitter as shown on
the transmitter (use a type CR2032 battery).
4. Put the two halves back together. Make sure the
halves are together tightly so water won't get in.
5. Resynchronize and then test the transmitter.