lock OLDSMOBILE SILHOUETTE 1993 Repair Manual
[x] Cancel search | Manufacturer: OLDSMOBILE, Model Year: 1993, Model line: SILHOUETTE, Model: OLDSMOBILE SILHOUETTE 1993Pages: 323, PDF Size: 17.13 MB
Page 194 of 323

Problems on the Road
192
Towing Your Oldsmobile (CONT.:)
When you call, tell the towing service:
That your vehicle cannot be towed
from the front with sling-type
equipment.
drive.
vehicle. lever.
damaged.
That your vehicle has front-wheel
The make, model, and year of your
Whether you can still move the shift
If there was an accident, what was
When the towing service arrives, let the
tow operator know that this manual
contains detailed towing instructions and
illustrations. The operator may want to
see them.
1 X6016
m,. ,
L ‘~‘n help avoid injury to you or
0 Never let passengers ride in a
vehicle that is
being towed.
* Never tow faster than safe or
0 Never tow with damaged parts
0 Never get under your vehicle
posted speeds.
not fully secured.
after it has been lifted by the tow
truck.
chains on each side when towing
a vehicle.
Never use “J” hooks. Use T-
hooks instead.
* Always use separate safety When your vehicle is being towed, have
the
ignition key
off. The steering wheel
should be clamped in a straight-ahead
position, with
a clamping device
designed for towing service. Do not use
the vehicle’s steering column lock for
this. The transaxle should be
in Neutral
and the parking brake released.
Don’t have your vehicle towed on
the
front wheels, unless you must. If the
vehicle must be towed on the front
wheels, don’t
go more than 35 mph
(56 km/h) or farther than 50 miles
(80 km) or your transaxle will be
damaged. If these limits must be
exceeded,
then the front wheels have to
be supported on a dolly.
ProCarManuals.com
Page 208 of 323

Problems on the Road
206
Changing a Elat Tire (corn)
4. The compact spare tire is located
under the vehicle, behind the rear
bumper. Insert the narrow end
of the
shaft into
the hole above the rear
bumper. Then attach the folding
wrench to the shaft.
5. Rotate the folding wrench counter-
clockwise to lower the compact spare
tire until it can be pulled from under
the vehicle.
6. Slide the cable retainer through the center
of the spare, then place the
compact spare tire near the flat tire.
7. Each wheel nut is covered with a
nylon cap. Use the folding wrench to
remove the nylon caps from the
wheel
nuts before you loosen the
nuts.
ProCarManuals.com
Page 209 of 323

8. Loosen the wheel nuts-but do not
remove them-using the folding
wrench. 9. Attach the folding wrench to the jack,
and rotate the wrench clockwise to
raise the jack head a few inches. 10. Near each wheel, there is a notch in
the vehicle's frame. Position the
jack and raise the jack head until
it
fits firmly into the notch in the
vehicle's frame nearest the flat tire.
Do not raise the vehicle yet. Put the
compact spare tire near you.
A
Getting under a vehicle when
it is jacked up is dangerous. If
the vehicle slips off the jack, you
could be badly injured or killed.
Never get under a vehicle when
it
is supported only by a jack.
207
ProCarManuals.com
Page 210 of 323

Problems on the Road
I Changing a Flat Tire (conm)
208
YO' I
1 1. Raise the vehicle by rotating the
folding wrench clockwise
in the
jack. Raise the vehicle far enough
off
the ground so there is enough
room for the spare tire to
fit.
12. Remove all the wheel nuts and take
off the flat tire.
ProCarManuals.com
Page 211 of 323

13. Remove any corrosion or dirt from I 14. Replace the wheel nuts with the
the wheel bolts, mounting surfaces
or spare wheel. Place the spare on
the wheel mounting surface.
Never use oil
or grease on I
~ studs or nuts. If you do, the
I nuts might come loose. Your whel
luld fall
off, causing a serious
accident.
1
rounded end of the nuts toward the
wheel. Tighten each
nut by hand
until the wheel is held against the
hub.
1 5. Lower the vehicle by attaching the
folding wrench
to the jack and
rotating the wrench counter-
clockwise. Lower the jack
completely.
1
209
ProCarManuals.com
Page 214 of 323

Problems on the Road
Compact Spare Tire
Although the compact spare was fully
inflated when your vehicle was new, it
can lose air after a time. Check the
inflation pressure regularly. It should
be
60 psi (420 Pa). The compact spare is
made to go up to
3,000 miles (5 000 km),
so you can finish your trip and have
your full-size tire repaired or replaced
where you want.
Of course, it’s best to
replace your spare with a full-size tire as
soon as you can. Your spare will last
longer and be
in good shape in case you
need it again.
Your anti-lock brake system warning
light may come on when you are driving
with a compact spare. See the
Index
under Anti-Lock Brake System Warning
Light.
Don’t use your compact spare on some
Don’t take your compact spare other vehicle.
through an automatic car wash
with guide rails. The compact
spare can get caught on the rails.
That can damage the tire and
wheel, and maybe other parts
of
your vehicle. And don’t
mix your compact
spare or
wheel with other wheels
or tires. They
won’t fit. Keep your spare
and its wheel
together.
ProCarManuals.com
Page 221 of 323

To check on fuel availability, ask an auto
club, or contact
a major oil company
that does business in the country where
you'll be driving.
You can
also write us at the following
address for advice. Just tell us where
you're going and give your Vehicle
Identification Number (VIN)
.
General Motors of Canada Ltd.
International
Export Sales
P.O. Box 828
Oshawa, Ontario LlH 7N1, Canada
Remote Fuel Door Release
The remote fuel door release can help
keep your fuel tank from being siphoned. Always be sure the fuel door
is closed and latched after refueling.
To open the fuel door (on the left rear
fender), lift the release lever beside the
driver's seat.
Filling Your Tank
The cap is behind a hinged door on the
left side
of your vehicle.
h nammable. It burns violently,
lsoline vapor is highly
ana that can cause very bad
injuries. Don't smoke if you're
near gasoline or refueling your
vehicle. Keep sparks, flames, and
smoking materials away from
gasoline. I
1
To take off the cap, turn it slowly to the
left (counterclockwise).
219
ProCarManuals.com
Page 231 of 323

Engine Oil Additives
Don't add anything to your oil. Your
Oldsmobile dealer is ready to advise if
you think something should be added.
When to Change Engine Oil
See if any one of these is true for you:
Most trips are less than 4 miles (6 km).
It's below freezing outside and most
trips are less than
10 miles (16 km).
The engine is at low speed most of the
time (as in door-to-door delivery, or in
stop-and-go traffic).
You tow a trailer often.
Most trips are through dusty places.
If any one of these is true for your
vehicle, then
you need to change your
oil and filter every 3,000 miles
(5 000 km) or 3 months-whichever
comes first.
If none of them is true, change the oil
every 7,500 miles (12 500 km) or 12
months-whichever comes first. Change
the filter at the first oil change and at
every other oil change after that.
Engine Block Heater (omoN)
An engine block heater can be a big
help if you have to park outside in very
cold weather,
0°F (-18" C) or colder. If
your vehicle has this option, see the
Index under Engine Block Heater.
229
ProCarManuals.com
Page 245 of 323

Halogen Bulbs
Halogen bulbs have
Headlight Bulb Replacement
For the type of bulb, see the Index under
Replacement Bulbs.
- pressurized gas inside and can
burst
if you drop or scratch 1- .. .. * 3
bulb. You or others could be
injured. Take special care whe-
handling and disposing
of halosG,
bulbs.
I
YOU can get nun ~y naogen
Touch or move the t: I w
Drop UI~ bulb.
Scratch the bulb.
hot.
1. Remove
the two black knobs.
2. Tilt the bulb housing forward.
3. Twist the L-shaped bulb assembly
counterclockwise
f/6 turn until the
flanges align with the slots
in the
retainer ring.
4. Pull out the bulb assembly.
5. Disconnect the bulb wiring harness
from the bulb assembly by lifting the
plastic loclung
tab.
6. Snap a new bulb assembly onto the
wiring harness.
7. Replace the bulb assembly by
reversing step
3.
8. Replace the bulb housing and the two
black knobs.
243
ProCarManuals.com
Page 246 of 323

Service & Appearance Care
Taillight Bulb Replacement
For the type of bulb, see the Ida under
Replacement Bulbs.
1. Open the rear side windows and
2. Remove the two screws from the
3. Undo the spring clips under the
liftgate.
taillight housing.
weatherstrip at the rear
of the side
window.
4. Pull off the entire taillight housing.
5. Pinch the lever and twist the bulb
assembly
yS turn counterclockwise to
remove.
6. Remove the bulb by pressing in and
turning
y8 turn counterclockwise.
7. Line up the small retainer bumps on
the replacement bulb
so that the
lower bump slides into the deepest
slot in the housing. Press
in and twist
the bulb
y8 turn clockwise.
Reposition the bulb assembly in the
taillight housing.
Turn the assembly
y6 turn clockwise to lock in place.
and screws.
8. Replace the entire taillight housing
9. Attach the spring clips to the
taillight housing and secure them.
liftgate. signals and taillights.
IO. Close the rear side windows and
1 1. Test the bulbs by using your turn
ProCarManuals.com