Display Peugeot 1007 Dag 2008.5 Workshop Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008.5, Model line: 1007 Dag, Model: Peugeot 1007 Dag 2008.5Pages: 194, PDF Size: 11.23 MB
Page 112 of 194
7
105
Steering wheel controls
This system's controls are grouped
together on lever A .
1. Speed limiter mode selection dial
2. Value decrease button
3. Value increase button
4. Speed limiter on/off button Instrument panel display
The programmed information is
grouped together on the instrument
panel display.
5. Speed limiter on/off indication
6. Speed limiter mode selection in-
dication
7. Programmed speed value
SPEED LIMITER
This speed limiter, of the new genera-
tion, has a display on the instrument
panel to indicate the programmed
speed.
It prevents exceeding of the vehicle
speed programmed by the driver.
When the programmed speed is
reached, pressing the accelerator
pedal no longer has any effect.
The limiter operates with a pro-
grammed speed of at least 18 mph
( 3 0 k m / h ) ; i t r e m a i n s a c t i v e r e g a r d -
less of any action on the brake and
clutch pedals.
The speed limiter is switched on
manually: it requires a programmed
s p e e d o f a t l e a s t 1 8 m p h ( 3 0 k m / h ) .
The speed limiter is switched off by
manual operation of the control.
By pressing the accelerator pedal
fi r m l y , p a s s i n g t h e p o i n t o f r e s i s -
tance, it is possible to exceed the
programmed speed temporarily.
To return to the programmed speed,
simply slow down to a speed below
the programmed speed.
The programmed speed value remains
in the memory when the ignition is
switched off.
Page 113 of 194
7
106
Operating fault
If a speed limiter malfunction occurs,
t h e s p e e d i s r e p l a c e d b y fl a s h i n g
dashes. Contact a PEUGEOT dealer
to have the system checked.
Activating/deactivating the limiter
Switch the speed limiter on by
pressing button 4 .
Programming
Place the dial 1 in the LIMIT posi-
tion. The limiter is not yet active.
By default, the display indicates
the last speed programmed: Return to normal driving
Turn dial 1 to position "0" : the
speed limiter mode is deselected.
The display returns to the dis-
tance recorder.
In the event of a steep de-
scent or sharp acceleration,
the speed limiter will not be
able to prevent the vehicle
from exceeding the pro-
grammed speed.
In any event, the speed limiter cannot
replace the need to observe speed
limits, nor can it replace the need for
vigilance and responsibility on the
part of the driver.
The driver must remain alert and stay
in complete control of his vehicle.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
Set the speed value by press-
ing button 2 or 3 ( e . g . : 7 0 m p h
( 1 1 0 k m / h ) ) .
You can then change the programmed
speed using buttons 2 and 3 :
- b y + o r - 1 m p h ( 1 k m / h ) = s h o r t press,
-
b y + o r - 5 m p h ( 5 k m / h ) = l o n g p r e s s ,
- i n s t e p s o f + o r - 5 m p h ( 5 k m / h ) = maintained press. Exceeding the programmed
speed
Pressing the accelerator pedal to
exceed the programmed speed will
not have any effect, unless you press
the pedal
fi r m l y passing the point of
resistance .
The speed limiter is deactivated tem-
porarily and the programmed speed,
w h i c h i s s t i l l d i s p l a y e d , fl a s h e s .
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
c a n c e l s t h e fl a s h i n g a u t o m a t i c a l l y
and reactivates the speed limiter.
Switch the speed limiter off by
pressing button 4 : the display
c o n fi r m s t h a t i t i s o f f ( O F F ) .
Switch the speed limiter back on
by pressing button 4 again.
Page 114 of 194
7
1 0 7
CRUISE CONTROL
This cruise control, of the new genera-
tion, is linked with the speed limiter. It
has a display on the instrument panel
to indicate the memorised reference
speed.
It enables the vehicle to maintain a
steady speed programmed by the
driver.
The cruise control is switched on
manually: it requires a minimum ve-
h i c l e s p e e d o f 2 5 m p h ( 4 0 k m / h ) a n d
fourth gear must be engaged on the
manual gearbox.
The cruise control is switched off
by means of a manual action or by
pressing the brake or clutch pedal or
in the event of activation of the ESP.
By pressing the accelerator pedal, it is
possible to exceed the programmed
speed temporarily.
To return to the programmed speed,
simply release the accelerator pedal.
Switching off the ignition or turning
the dial cancels any programmed
speed value. Instrument panel display
The programmed information is
grouped together on the instrument
panel display.
5. Cruise control on/off indication
6. Cruise control mode selection in-
dication
7. Programmed speed value
Steering wheel controls
This system's controls are grouped
together on lever
A .
1. Cruise control mode selection dial
2. Value decrease button
3. Value increase button
4. Cruise control on/off button
Page 115 of 194
7
108
Exceeding the programmed speed
Intentional or unintentional exceeding
of the programmed speed results in
fl a s h i n g o f t h e p r o g r a m m e d s p e e d
on the display.
Returning to the programmed speed,
by means of intentional or uninten-
tional deceleration of the vehicle,
c a n c e l s t h e fl a s h i n g a u t o m a t i c a l l y .
Using the accelerator:
exceed the memorised speed until
the required speed is reached,
press button 2 or 3 .
Programming
Place switch 1 in the CRUISE
position. The cruise control is
not yet active and no speed has
been memorised. The display
indicates: Cancelling the cruise control
Switch the cruise control off by
pressing button 4 : the display
c o n fi r m s t h a t i t i s o f f ( O F F ) .
When changing the memo-
rised reference speed by
means of a maintained
press, pay attention as
the speed can increase or
decrease rapidly.
Do not use the cruise control on slip-
p e r y r o a d s o r i n h e a v y t r a f fi c .
In the event of a steep slope, the
cruise control cannot prevent the
vehicle from exceeding the pro-
grammed speed.
In any event, the cruise control can-
not replace the need to comply with
speed limits, nor can it replace the
need for vigilance and responsibility
on the part of the driver.
To prevent the mat from becoming
caught under the pedals:
- ensure that the mat is positioned correctly.
- n e v e r fi t o n e m a t o n t o p o f a n o t h e r .
It is advisable to keep your feet near
the pedals.
Set the programmed speed by
accelerating to the required
speed, then press button 2 or 3
( e . g . : 7 0 m p h ( 1 1 0 k m / h ) ) .
Return to normal driving
Turn dial 1 to position "0" : the
cruise control mode is dese-
lected. The display returns to the
distance recorder. Operating fault
If a cruise control malfunction occurs,
t h e s p e e d i s r e p l a c e d b y fl a s h i n g
dashes. Contact a PEUGEOT dealer
to have the system checked.
You can then change the programmed
speed using buttons 2 and 3 :
- b y + o r - 1 m p h ( 1 k m / h ) = s h o r t press,
-
b y + o r - 5 m p h ( 5 k m / h ) = l o n g p r e s s ,
- i n s t e p s o f + o r - 5 m p h ( 5 k m / h ) = m a i n t a i n e d p r e s s . Reactivating the cruise control
Switch the cruise control back on
by pressing button 4 again.
Page 116 of 194
7
109
VISUAL AND AUDIBLE REAR PARKING ASSISTANCE
This system consists of four proximity
sensors, located in the rear bumper,
and a special speaker.
T h i s d e t e c t s a n y o b s t a c l e ( p e r s o n ,
vehicle, tree, gate, etc.) behind the
vehicle. Nevertheless, it cannot
detect obstacles located just below
the bumper.
An object, such as a stake, a road-
works cone or any other similar
object may be detected at the begin-
ning of the manoeuvre, but may no
longer be detected when the vehicle
comes close to it. Detection zone
Activation
The system is activated as soon as
reverse gear is engaged, accompa-
nied by an audible signal. The proxi-
mity information is given by:
- an audible signal, which beco-
mes more rapid as the vehicle
approaches the obstacle.
- a graphic on the multifunction display, with blocks which be-
come increasingly close to the
vehicle. When the distance between the rear
of the vehicle and the obstacle is less
than thirty centimetres, the audible
signal becomes continuous and the
"Danger" symbol appears on the
multifunction display.
On completion of the manoeuvre,
when you exit reverse gear, the sys-
tem becomes inactive.
The rear parking assistance sys-
tem cannot, in any circumstances,
take the place of the vigilance and
responsibility of the driver.
Page 117 of 194
7
110
If there is an operating fault,
when reverse gear is enga-
ged, the service warning
light comes on, accompa-
nied by an audible signal
( s h o r t b l e e p ) a n d a m e s s a g e
on the multifunction display.
In bad or wintry weather, ensure that
the sensors are not covered with
mud, frost or snow.
Deactivation
With the engine running, press button A
to deactivate the system permanently.
The indicator light on the button comes
on.
The system will be deactivated
automatically when towing a trailer or
w h e n a b i c y c l e c a r r i e r i s fi t t e d ( v e h i c l e
fi t t e d w i t h a t o w b a r o r b i c y c l e c a r r i e r
recommended by PEUGEOT ).
Reactivation
Press button A again to reactivate
the system. The indicator light on the
button is switched off.
Page 121 of 194
8
115
CHECKING THE LEVELS
There are two marks on
the dipstick:
A = maximum
N e v e r fi l l p a s t t h i s m a r k .
B = minimum
Dipstick
Oil change
According to the information given in
the servicing booklet. Changing the brake fluid
T h e b r a k e fl u i d m u s t b e
changed at the intervals
stated, according to the
manufacturer's servicing
schedule.
U s e fl u i d s r e c o m m e n d e d b y t h e m a n -
u f a c t u r e r , w h i c h f u l fi l D O T 4 s t a n d a r d s . Windscreen and headlamp
wash level
For best quality cleaning and
for your safety, we would ad-
vise that you use products
recommended by PEUGEOT .
When the level is low, this is indicated
by an audible signal and a message
on the multifunction display.
Viscosity selection
In all cases, the oil selected must
meet the manufacturer's require-
ments.
Cooling system
U s e t h e fl u i d r e c o m m e n d e d b y t h e
manufacturer.
When the engine is warm, the tem-
perature of the coolant is controlled
by the engine fan. As this fan can ope
rate with the ignition key removed and
because the cooling system is pres-
surised, wait for at least one hour after
the engine has stopped before carry-
ing out any work.
Slacken the cap by two turns to re-
lease the pressure to prevent any
risk of scalding. When the pressure
has dropped, remove the cap and
top up the level. Diesel additive level (Diesel
with particle emission filter)
Lighting of the service warning light,
accompanied by a message and an
audible signal, indicates that the die-
sel additive level is low.
This additive must be topped up.
Contact a PEUGEOT dealer as soon
as possible.
To maintain the reliability of
engines and emission control
systems, the use of additives
in engine oil is prohibited. Used oil
Avoid prolonged contact of used oil
with the skin.
B r a k e fl u i d i s h a r m f u l t o h e a l t h a n d
very corrosive.
Note
: the coolant does not need to
be changed.
The level must always be
above the MIN mark and
close to the MAX mark. Do not dispose of used oil,
b r a k e fl u i d o r c o o l a n t i n t o
drains or into the ground.
Oil level
Check the level regularly
and top up between chang-
es. The maximum consump-
tion is 0.5 l per 600 miles
(1 000 km).
Check the level with the vehicle level,
engine cold, using the oil level gauge
on the instrument panel or the dip-
stick.
Page 131 of 194
9
124
Fuse N°RatingFunctions
115 ARear wiper.
35 AAir bags and pre-tensioners control unit.
410 ADiagnostic socket - Clutch switch - Steering wheel angle sensor - P a r t i c l e e m i s s i o n fi l t e r p u m p .
530 AElectric windows - Sunroof.
6-Not used.
75 ACourtesy light - Glove box lighting.
820 A T y r e u n d e r - i n fl a t i o n d e t e c t i o n c o n t r o l u n i t - E l e c t r i c m i r r o r f o l d i n g - A l a r m s i r e n - Multifunction display - Alarm control unit - Audio equipment - Aud io/telephone.
930 AAudio equipment - Lighter/12 V socket (100 W max).
1015 ASteering wheel controls.
1115 ADiagnostic socket - Low current ignition switch - Motorised strikers.
1215 AAir bags and pre-tensioners control unit - Rain/brightness sensor.
135 AABS relay - Speed sensor - Engine Fuse Box - "2 Tronic" gear lever - Brake swit ch.
1415 AParking assistance control unit - "Sesame" doors control unit and switches - Instrument panel - Seat belt warning lights bar - Air conditioning control panel - Headlamp adjustment - Hands-free kit.
1530 ALocking - Deadlocking - Unlocking.
1740 ARear screen and exterior mirrors demisting.
SH-PARC shunt.
Page 134 of 194
9
127
CHANGING A WINDSCREEN WIPER BLADE
Changing a front wiper blade
Lift the wiper arm.
Unclip the blade and remove it.
Fit the new blade.
Push back the wiper arm.
Note: t h e s h o r t e s t b l a d e i s fi t t e d o n
the right-hand wiper arm.
Changing the rear wiper blade
Lift the wiper arm.
Unclip the blade and remove it.
Fit the new blade.
Push back the wiper arm.
ECONOMY MODE FUNCTION
After the engine has stopped, certain
functions (doors, windscreen wipers,
electric windows, courtesy light, audio
equipment, dipped headlamps, etc.)
can only be used for a cumulative
duration of thirty minutes, to prevent
discharging of the battery.
Once the thirty minutes are over, a
message informing you of the switch
to economy mode appears on the
multifunction display and the active
functions are put on standby.
These functions are reactivated
automatically next time the vehicle is
driven.
To resume the use of these functions
immediately, start the engine and let
it run for a few minutes.
The time available to you will then be
double the duration for which the en-
gine is left running. However, this pe-
r i o d w i l l a l w a y s b e b e t w e e n fi v e a n d
thirty minutes.
Note: if the telephone is being used
when economy mode starts, it will
s t i l l b e p o s s i b l e t o fi n i s h t h e c a l l .
A fl a t b a t t e r y w i l l p r e v e n t t h e
engine from starting.
FITTING/REMOVING THE MAT
When removing the mat on the dri-
ver's side, push the seat as far back
a s p o s s i b l e a n d r e m o v e t h e fi x i n g s .
W h e n r e fi t t i n g , p o s i t i o n t h e m a t
correctly on the pins and clip the
fi x i n g s . C h e c k t h a t t h e m a t i s s e c u r e d
correctly.
To prevent the mat from becoming
caught under the pedals:
- only use mats suited to the fi x i n g s a l r e a d y p r e s e n t i n t h e
vehicle. It is imperative that these
fi x i n g s a r e u s e d .
- n e v e r fi t o n e m a t o n t o p o f another.
Placing the wiper blades in the
special position
Less than a minute after switching
off the ignition, operate the wip-
ers stalk to position the wiper
blades in the centre of the wind-
screen.
To return the windscreen wipers
to their normal position, switch on
the ignition and operate the wipers
stalk.
Page 147 of 194
140
01
22
11
5 5
3344
88
9 9
1010 1 5 1 5
11111717
18181212
1616
1414
7766
1313
1. Ejection of the CD.
2. Selection of the source: radio, Jukebox, CD,
C D c h a n g e r a n d a u x i l i a r y ( A U X , i f a c t i v a t e d o n t h e C o n fi g u r a t i o n m e n u ) .
L o n g p r e s s : C D c o p y t o h a r d d i s c .
3. L o n g p r e s s o n t h e S O S b u t t o n : e m e r g e n c y c a l l .
4. Selection of the display on the screen from the m odes: TRIP,
T E L , N A V a n d A U D I O .
5 . M o d i fi c a t i o n o f t h e s c r e e n d i s p l a y .
L o n g p r e s s : r e i n i t i a l i s a t i o n o f t h e W I P C o m .
6. O n / O f f a n d V o l u m e a d j u s t m e n t .
7. S e l e c t i o n o f t h e w a v e b a n d s F M 1 , F M 2 , F M a s t , A M .
8. T A ( T r a f fi c A n n o u n c e m e n t ) f u n c t i o n o n / o f f .
L o n g p r e s s : a c c e s s t o t h e P T Y ( r a d i o P r o g r a m m e T Y p e s ) m o d e .
9 . A c c e s s t o t h e " P E U G E O T " s e r v i c e s m e n u .
10. Cancellation of the current operation.
L o n g p r e s s : r e t u r n t o t h e c u r r e n t a p p l i c a t i o n .
11. A u t o m a t i c s e a r c h f o r a l o w e r / h i g h e r f r e q u e n c y .
Selection of the previous/next CD, MP3 or Jukebox track.
12. D i s p l a y i n g o f t h e g e n e r a l m e n u .
13. K e y p a d f o r e n t e r i n g d e s c r i p t i o n s b y s u c c e s s i v e p r e s s e s .
14. Selection of the previous/next CD. Selection of t he previous/
next MP3/Jukebox directory.
1 5 . A u d i o o p t i o n a d j u s t m e n t s : f r o n t / r e a r , l e f t / r i g h t b a l a n c e ,
loudness, sound ambiences.
16. S e l e c t i o n a n d c o n fi r m a t i o n .
17. SIM card slot.
18. D i s p l a y i n g o f t h e l i s t o f l o c a l r a d i o s t a t i o n s ,
of the tracks on the CD or of the MP3/Jukebox dire ctories.
L o n g p r e s s : u p d a t i n g o f t h e l o c a l r a d i o s t a t i o n s .
FIRST STEPS