lock PEUGEOT 206 2008 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2008, Model line: 206, Model: PEUGEOT 206 2008Pages: 127, PDF Size: 1.44 MB
Page 65 of 127
59
ACCESS
-
DOORS
Opening the doors from inside Locking/Unlocking from inside
"Door open" warning
With the engine running, you are
w a r n e d i f a d o o r i s n o t s h u t p r o p e r l y
by an audible signal and a message
or graphic on the multifunction dis-
p l a y , i n d i c a t i n g t h e d o o r i n q u e s t i o n .
When the vehicle is moving, if the
courtesy light button is in the "light-
i n g o n o p e n i n g a d o o r " p o s i t i o n , t h e
c o u r t e s y l i g h t l a s h e s .
Without central locking
T o l o c k , p r e s s b u t t o n
A. The button
locks the door in question.
The button on the driver’s door locks
the door and the tailgate.
T o u n l o c k , p u l l b u t t o n A or operate
the handle. With central locking
Press button
B to lock/unlock.
Opening the doors from outside
Page 66 of 127
ACCESS
60 -
CHILD SAFETY LOCK
On each rear door this prevents
opening of the door from the inside.
T u r n s w i t c h 1 an eighth turn (45 de-
grees) using the ignition key.
Automatic central locking of the
doors
The doors can lock automatically
w h e n y o u a r e d r i v i n g ( a t a s p e e d o f
more than 6 mph (10 km/h)).
A b o v e 6 m p h ( 1 0 k m / h ) , p r e s s b u t
-
ton B b r i e l y t o u n l o c k t h e d o o r s t e m -
porarily.
You can activate or deactivate this
function. To switch off
Press and hold button
B.
Notes: i f o n e o f t h e d o o r s i s o p e n ,
locking from the inside and automatic
central locking are not possible.
I f t h e b o o t i s o p e n , a u t o m a t i c c e n t r a l
locking of the doors is possible.
To switch on
Press and hold button
B.
Activation of the function is accom-
panied by an audible signal and a
message on the multifunction display.The message is displayed each time
the vehicle is started.
Page 67 of 127
61
ACCESS
-
LOCKING/UNLOCKING
THE TAILGATE
Without central locking
T o l o c k , t u r n t h e k e y f r o m A to C.
T o o p e n , t u r n t h e k e y f r o m A to B ,
press the handle then lift the tail-
gate.
TAILGATE RELEASE
This enables the tailgate to be un-
locked in the event of a central locking
fault:
- Fold back the rear seats to gain access to the boot from inside
t h e v e h i c l e ,
- P u l l t h e t a i l g a t e t r i m t o r e l e a s e i t ,
- Pull the opening catch 1
u p w a r d s .
"Boot open" warning
If the tailgate is not shut properly:
-
with the engine running, you
a r e w a r n e d b y a n a u d i b l e s i g n a l
and a message or graphic on the
m u l t i f u n c t i o n d i s p l a y ,
- when the vehicle is moving,
t h e c o u r t e s y l i g h t l a s h e s i f t h e
courtesy light button is in this
position.
With central locking
Locking and unlocking of the tailgate
i s s i m u l t a n e o u s w i t h t h e d o o r s .
The lighting is activated on opening
the tailgate.
Page 68 of 127
ACCESS
62 -
OPENING THE BONNET
Inside the vehicle: pull the handle on
t h e l e f t - h a n d s i d e , u n d e r t h e f a s c i a .
Outside the vehicle: lift the catch
and raise the bonnet.
BONNET STRUTSecure the strut to hold the bonnet
open.
B e f o r e c l o s i n g t h e b o n n e t , r e p l a c e
the strut in its housing.
FILLING THE FUEL TANK
T h e t a n k m u s t b e i l l e d w i t h f u e l w i t h
the engine switched off .
Insert the key then turn it to the left.
Remove the cap.
A l a b e l i n d i c a t e s w h i c h t y p e o f f u e l t o
use.
I f y o u i l l y o u r t a n k , d o n o t c o n t i n u e
after the third cut-off of the pump
nozzle. This could result in vehicle
malfunctions.
The capacity of the tank is approxi-
mately 50 litres.
To close
L o w e r t h e b o n n e t a n d r e l e a s e i t a t
the end of its travel.
Check that the bonnet is locked.
Page 70 of 127
VISIBILITY
64 -
"Follow me home" lighting
W h e n y o u l e a v e y o u r v e h i c l e , t h e
side lights and dipped headlamps
can be left on for approximately
30 seconds.
To do this:
- place the key in the STOP
p o s i t i o n ,
- place the lights stalk in the 0 p o s i t i o n ,
- l a s h t h e h e a d l a m p s ,
- get out of the vehicle and lock it.AUTOMATIC SWITCHING ON
OF LIGHTS
The side lights and dipped beam
h e a d l a m p s s w i t c h o n a u t o m a t i c a l -
l y i f t h e l i g h t i s p o o r a n d w h e n t h e
w i n d s c r e e n w i p e r s o p e r a t e c o n t i n u -
o u s l y a n d s w i t c h o f f w h e n t h e l i g h t
b e c o m e s b r i g h t e n o u g h o r t h e w i n d -
s c r e e n w i p e r s a r e s w i t c h e d o f f .
In foggy weather or in snow, the
brightness sensor can detect suf-
i c i e n t l i g h t , t h e l i g h t s w i l l n o t
come on automatically. If neces-
sary, the dipped headlamps must
be switched on manually.
T h i s f u n c t i o n i s a c t i v e w h e n t h e v e -
hicle is supplied to the customer.
To disarm or activate the function:
- Place the key in the accessories p o s i t i o n ( 1 s t n o t c h ) ,
- Place the lights stalk in the AUTO/0 p o s i t i o n ,
- Press the end of the lights stalk for more than four seconds.
Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen, behind the interior mirror.
It is used for automatic switching
on of the lights. Operating check
I n g o o d o r r a i n y w e a t h e r ,
b o t h d a y a n d n i g h t , t h e
front fog lamps and the
rear fog lamp are dazzling
and are prohibited.
D o n o t f o r g e t t o s w i t c h t h e m o f f
w h e n t h e y a r e n o l o n g e r n e e d e d .
Direction indicators
( l a s h e r s ) Left: d o w n w a r d s .
Right: u p w a r d s . Disarming
The disarmed function is accompa-
nied by an audible signal.
When the driver uses the manual
l i g h t i n g c o n t r o l s , t h e f u n c t i o n i s t e m
-
porarily disarmed.
If the brightness sensor does not
function correctly, the lights come
on accompanied by an audible signal
and a message on the multifunction
display.
Consult a PEUGEOT dealer.
Activation
The activated function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Page 71 of 127
VISIBILITY
64 -
"Follow me home" lighting
W h e n y o u l e a v e y o u r v e h i c l e , t h e
side lights and dipped headlamps
can be left on for approximately
30 seconds.
To do this:
- place the key in the STOP
p o s i t i o n ,
- place the lights stalk in the 0 p o s i t i o n ,
- l a s h t h e h e a d l a m p s ,
- get out of the vehicle and lock it.AUTOMATIC SWITCHING ON
OF LIGHTS
The side lights and dipped beam
h e a d l a m p s s w i t c h o n a u t o m a t i c a l -
l y i f t h e l i g h t i s p o o r a n d w h e n t h e
w i n d s c r e e n w i p e r s o p e r a t e c o n t i n u -
o u s l y a n d s w i t c h o f f w h e n t h e l i g h t
b e c o m e s b r i g h t e n o u g h o r t h e w i n d -
s c r e e n w i p e r s a r e s w i t c h e d o f f .
In foggy weather or in snow, the
brightness sensor can detect suf-
i c i e n t l i g h t , t h e l i g h t s w i l l n o t
come on automatically. If neces-
sary, the dipped headlamps must
be switched on manually.
T h i s f u n c t i o n i s a c t i v e w h e n t h e v e -
hicle is supplied to the customer.
To disarm or activate the function:
- Place the key in the accessories p o s i t i o n ( 1 s t n o t c h ) ,
- Place the lights stalk in the AUTO/0 p o s i t i o n ,
- Press the end of the lights stalk for more than four seconds.
Do not cover the brightness sen-
sor, coupled with the rain sensor,
located in the centre of the wind-
screen, behind the interior mirror.
It is used for automatic switching
on of the lights. Operating check
I n g o o d o r r a i n y w e a t h e r ,
b o t h d a y a n d n i g h t , t h e
front fog lamps and the
rear fog lamp are dazzling
and are prohibited.
D o n o t f o r g e t t o s w i t c h t h e m o f f
w h e n t h e y a r e n o l o n g e r n e e d e d .
Direction indicators
( l a s h e r s ) Left: d o w n w a r d s .
Right: u p w a r d s . Disarming
The disarmed function is accompa-
nied by an audible signal.
When the driver uses the manual
l i g h t i n g c o n t r o l s , t h e f u n c t i o n i s t e m
-
porarily disarmed.
If the brightness sensor does not
function correctly, the lights come
on accompanied by an audible signal
and a message on the multifunction
display.
Consult a PEUGEOT dealer.
Activation
The activated function is accompa-
nied by an audible signal and a mes-
sage on the multifunction display.
Page 77 of 127
LAYOUT
70 -
HEADLAMP ADJUSTMENT
D e p e n d i n g o n t h e l o a d i n y o u r v e h i c l e ,
it is recommended that the headlamp
beam is adjusted.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
2. 5 people + maximum
authorised load.
3. Driver + maximum
authorised load.
Initial setting is position 0.
STEERING WHEEL HEIGHT
ADJUSTMENT
W h e n s t a t i o n a r y , l o w e r t h e h a n d l e t o
u n l o c k t h e s t e e r i n g w h e e l .
Adjust to the desired height and
lift the handle to lock the steering
w h e e l .
HORN
Press one of the spokes of
t h e s t e e r i n g w h e e l .
Page 89 of 127
81
SAFETY
-
ANTI-LOCK BRAKING
SYSTEM (ABS) AND
ELECTRONIC BRAKE FORCE
DISTRIBUTION (EBFD)
T h e A B S , i n c o n j u n c t i o n w i t h t h e
e l e c t r o n i c b r a k e f o r c e d i s t r i b u t i o n ,
increases the stability and manoeu-
v r a b i l i t y o f y o u r v e h i c l e o n b r a k i n g ,
in particular on poor or slippery road
surfaces.
W h e n c h a n g i n g w h e e l s ( t y r e s a n d
r i m s ) , m a k e s u r e t h a t t h e s e a r e a p -
proved.
The anti-lock braking system comes
i n t o o p e r a t i o n a u t o m a t i c a l l y w h e n
t h e r e i s a r i s k o f w h e e l l o c k .
EMERGENCY BRAKING
ASSISTANCE SYSTEM
I n a n e m e r g e n c y , t h i s s y s t e m e n a -
bles the optimum braking pressure to
b e r e a c h e d m o r e q u i c k l y , t h u s r e d u c -
ing the stopping distance.
I t i s t r i g g e r e d b y t h e s p e e d a t w h i c h t h e
brake pedal is activated. The effect of
this is a reduction in the resistance of
the pedal and an increase in braking
e f i c i e n c y .
W h e n b r a k i n g i n a n e m e r g e n c y ,
p r e s s i r m l y w i t h o u t r e l e a s i n g t h e
pressure.
Depending on the force of the decel-
e r a t i o n , t h e h a z a r d w a r n i n g l i g h t s a r e
s w i t c h e d o n a u t o m a t i c a l l y . T h e y a r e
s w i t c h e d o f f a u t o m a t i c a l l y o n a c c e l -
eration.
W h e n t h i s w a r n i n g l i g h t
c o m e s o n , a c c o m p a n i e d b y
a b u z z e r a n d a m e s s a g e , i t
indicates that there is a mal-
f u n c t i o n o f t h e A B S , w h i c h c a n c a u s e
a l o s s o f c o n t r o l o f t h e v e h i c l e w h e n
braking. W h e n t h i s w a r n i n g l i g h t
c o m e s o n , c o n n e c t e d t o t h e
STOP
w a r n i n g l i g h t , a c c o m -
panied by a buzzer and a
m e s s a g e , i t i n d i c a t e s t h a t t h e r e i s a
malfunction of the electronic brake
f o r c e d i s t r i b u t i o n , w h i c h c a n c a u s e
a l o s s o f c o n t r o l o f t h e v e h i c l e w h e n
braking.
Stop immediately.
I n b o t h c a s e s , c o n s u l t a P E U G E O T
dealer.
Normal operation of the ABS may
make itself felt by slight vibrations
of the brake pedal.
In emergency braking, press
v e r y i r m l y w i t h o u t r e l e a s i n g t h e
pressure.
Page 119 of 127
PRACTICAL INFORMATION
108 -
Fitting/removing the mat
When removing the mat on the driver’s
s i d e , p u s h t h e s e a t a s f a r b a c k a s p o s -
s i b l e a n d r e m o v e t h e i x i n g s .
W h e n r e i t t i n g , p o s i t i o n t h e m a t c o r r e c t -
l y o n t h e p i n a n d c l i p t h e i x i n g s . C h e c k
that the mat is secured correctly.
To prevent the mat from becoming
caught under the pedals:
- only use mats suited to the i x i n g s a l r e a d y p r e s e n t i n t h e
vehicle. It is imperative that
t h e s e i x i n g s a r e u s e d .
- n e v e r i t o n e m a t o n t o p o f another. - Clean off bird drop-
p i n g s , r e s i n o u s d e p o s -
i t s , t a r s t a i n s a n d g r e a s e
marks as soon as pos-
s i b l e ; ( t h e s e a l l c o n t a i n
s u b s t a n c e s w h i c h c a n
cause serious damage
t o t h e p a i n t w o r k ) .
- Do not use a dry or abrasive cloth or detergent or solvent
products to clean the double
l e n s , c o m p l e x s u r f a c e h e a d -
l a m p s a s t h e y a r e i t t e d w i t h
polycarbonate glass covered
i n a p r o t e c t i v e i n i s h .
- D o n o t u s e p e t r o l , o i l o r c l o t h stain removers to clean the
b o d y w o r k a n d p l a s t i c p a r t s o f
your vehicle.
- To prevent the development of b o d y w o r k c o r r o s i o n a s a r e s u l t
of accidental damage (stone
c h i p s , s c r a t c h e s , e t c . ) h a v e
t h e m r e p a i r e d s w i f t l y .
BODYWORK MAINTENANCE
T o p r e s e r v e t h e p a i n t w o r k a n d t h e
p l a s t i c t r i m o n y o u r v e h i c l e , w e r e c o m -
m e n d t h a t y o u w a s h t h e m r e g u l a r l y .
- b y h a n d : t h e r e a r e n o s p e c i i c p r e c a u t i o n s t o t a k e ;
- u s i n g a n a u t o m a t i c c a r w a s h : r e -
peated use of poorly maintained
a u t o m a t i c c a r w a s h e s c a n l e a d
to the appearance of microscopic
s c r a t c h e s w h i c h g i v e t h e p a i n t -
w o r k a m a t t a p p e a r a n c e ( e s p e -
c i a l l y v i s i b l e o n d a r k c o l o u r s ) ;
- u s i n g a h i g h p r e s s u r e w a s h e r : a l w a y s f o l l o w t h e r e c o m m e n d a -
tions on the equipment (pres-
sure and spraying distance).
If there are damaged areas on the
vehicle (painted bumpers or head-
l a m p s ) , i t i s n o t r e c o m m e n d e d t o
direct the high pressure jet onto
them. Wash these areas by hand.
A l s o a v o i d t h e e n t r y o f w a t e r i n t o
the locks.
For all questions relating to the main-
t e n a n c e o f y o u r v e h i c l e , c o n t a c t a n
a p p r o v e d d e a l e r w h o c a n a d v i s e y o u
on quality products selected by our
departments.