headlamp PEUGEOT 207 2008 Owner's Manual

137
Changing the side lights

 Disconnect the main headlamp con-
nector.

 Remove the plastic protective cover
by pulling on the tab.

 Turn the bulb holder one quarter of
a turn and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
Changing the dipped headlamps,
main beam headlamps or directional
headlamps

 Disconnect the main headlamp con-
nector.

 Remove the corresponding plastic
protective cover by pulling on the
tab. Changing the integrated direction
indicator side repeaters

 Insert a screwdriver towards the
centre of the repeater between the
repeater and the base of the mirror.

 Tilt the screwdriver to extract the
repeater and remove the repeater.

 Disconnect the repeater connector.
To refi t, carry out these operations in
reverse order.
To obtain a replacement repeater, contact
a PEUGEOT dealer.

 Disconnect the connector of the cor-
responding light.

 Move aside the spring to release the
bulb and remove the bulb.
To refi t, carry out these operations in
reverse order. Changing the fog lamps
For replacement of these bulbs, contact
a PEUGEOT dealer.

!
139
Changing the third brake light bulbs
(4 bulbs W 5 W)

 Press on the fi xing pins on each side
of the light.

 Take out the light from the outside.

 Turn the bulb holder which corre-
sponds to the faulty bulb one quarter
of a turn and remove it.

 Pull the bulb and change it. Changing the number plate light
bulbs (W 5 W)

 Insert a thin screwdriver in one of
the exterior holes of the lens.

 Push it towards the outside to unclip it.

 Remove the lens.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lights and their
surrounds to avoid damaging their
varnish and their seal.

!
141
Changing the third brake light bulbs
(4 bulbs W 5 W)

 Remove the two light fi xing nuts.

 Take out the light from the outside.

 Press on the two tabs and remove
the bulb holder

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
Tighten the fi xing bolt suffi ciently by
hand to guarantee the sealing of the
light. Changing the number plate bulbs
(W 5 W)

 Insert a thin screwdriver into one of
the exterior holes of the lens.

 Push it towards the outside to unclip
it

 Remove the lens.

 Pull the bulb and change it.
High pressure washing
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lights and their
surrounds to avoid damaging their
varnish and their seal.

144

Fuse N° Rating Functions

F8 20 A Audio equipment, audio/telephone, CD changer,
multifunction display, clock, steering wheel controls,
tyre under-infl ation detection, trailer fuse box.

F9 30 A Front 12 V socket, rear 12 V socket (SW).

F10 15 A Alarm siren, alarm control unit, directional
headlamps.

F11 15 A Diagnostic socket, low current ignition switch,
automatic gearbox control unit.

F12 15 A Rain/brightness sensor, amplifi er, trailer fuse box,
driving school module.

F13 5 A Engine fuse box, ABS relay, dual-function brake
switch, "2 Tronic" gearbox gear lever.

F14 15 A Instrument panel, seat belt warning lights bar,
headlamp adjustment, air conditioning, hands-free
kit, rear parking assistance control unit, air bags.

F15 30 A Locking and deadlocking.

F17 40 A Rear screen and exterior mirrors de-icing.

SH - PARC shunt.

145
Engine compartment fuses
The fuse box is placed in the engine
compartment, near the battery (left-
hand side).
Access to the fuses

 Unclip the cover.

 Replace the fuse (refer to the cor-
responding paragraph).

 When you have fi nished, close the
cover carefully to guarantee the
sealing of the fuse box. Fuse table

Fuse N° Rating Functions

F1 20 A Engine control unit and fan assembly control relay
supply, timing and canister solenoid valves
(1.6 l 16V THP), air fl ow sensor (Diesel), injection
pump (Diesel), water in diesel sensor (Diesel),
EGR solenoid valves, air heating (Diesel).

F2 15 A Horn

F3 10 A Front and rear wash-wipe.

F4 20 A Headlamp wash.

F5 15 A Fuel pump (petrol), Turbo solenoid valves
(1.6 l 16V THP).

F6 10 A Vehicle speed sensor, automatic gearbox.

F7 10 A Electric power steering, directional headlamps,
directional headlamps control relay, switching and
protection unit (Diesel).

F8 25 A Starter control.

F9 10 A ABS/ESP control unit, brake pedal switch.

F10 30 A Engine control unit actuators (petrol: ignition
coils, solenoid valves, oxygen sensors, injectors,
heaters, controlled thermostat) (Diesel: solenoid
valves, heaters).

F11 40 A Air conditioning blower.

F12 30 A Windscreen wipers Low/High speed.

146

Fuse N° Rating Functions

F13 40 A Built-in systems interface supply
(ignition positive).

F14 30 A Diesel heater (Diesel).

F15 10 A Left main beam headlamp.

F16 10 A Right main beam headlamp.

F17 15 A Left dipped beam headlamp.

F18 15 A Right dipped beam headlamp.
* The maxi-fuses provide additional pro- tection for the electrical systems. All
work on the maxi-fuses must be car-
ried out by a PEUGEOT dealer. Maxi-fuse table

Fuse N° Rating Functions

Box 1

MF1 * 70 A Fan assembly.

MF2 * 20 A/30 A ABS/ESP pump.

MF3 * 20 A/30 A ABS/ESP solenoid valves.

MF4 * 60 A Built-in systems interface supply.

MF5 * 60 A Built-in systems interface supply.

MF6 * 30 A Additional fan assembly (1.6 l 16V THP).

MF7 * 80 A Passenger compartment fuse box.

Box 2

MF8 * 30 A "2 Tronic" gearbox ECU.

MF9 * 80 A Heating unit (Diesel).

MF10 * 80 A Electric power steering.

MF11 * 40 A Valvetronic electric motor (1.6 l 16V THP).

!
i
149
A fl at battery prevents the engine from
starting (refer to the corresponding
paragraph).
If the telephone is being used at
this time:
- it will be maintained for 5 minutes with the RD4 audio equipment
hands-free kit,
- it will still be possible to fi nish the call with the RT4 GPS au-
dio/telephone.
ENERGY ECONOMY MODE
System which manages the duration of
use of certain functions to conserve a
suffi cient level of charge in the battery.
After the engine has stopped, you can
still use functions such as the audio
equipment, windscreen wipers, dipped
headlamps, courtesy lights, etc. for a
maximum combined duration of
thirty minutes. Exiting economy mode
These functions are reactivated auto-
matically next time the vehicle is driven.

 In order to resume the use of these
functions immediately, start the en-
gine and let it run for a few minutes.
The time available to you will then be
double the duration for which the en-
gine is left running. However, this period
will always be between fi ve and thirty
minutes.
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multi-function
display indicating that the vehicle has
switched to economy mode and the ac-
tive functions are put on standby.
CHANGING A WIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
of tools.
Removing a front or rear wiper
blade

 Raise the corresponding wiper arm.

 Unclip the wiper blade and remove it.
Fitting a front or rear wiper
blade

 At the front, check the size of the
wiper blade as the shorter blade is
fi tted on the right-hand side of the
vehicle.

 Put the corresponding new wiper
blade in place and clip it.

 Fold down the wiper arm carefully.