fog light bulb PEUGEOT 207 2008 Owners Manual

!
i
i
136
CHANGING A BULB
Procedure for the replacement of a
faulty bulb with a new bulb without the
use of tools.
1. Direction indicators
(PY 21 W amber).

2. Side lights (W 5 W).

3. Dipped headlamps (H7 - 55 W).

4. Main beam headlamps
(H1 - 55 W).

5. Directional headlamps
(H7 - 55 W).

6. Fog lamps (H11 - 55 W). Changing the direction indicators

 Handle the bulbs with a dry
cloth.
The headlamps are fi tted with poly-
carbonate glass with a protective
coating:

 do not clean them using a dry
or abrasive cloth, or using a
detergent or solvent product,

 use a sponge and soapy water. In certain climatic conditions (low
temperature, humidity),
conden-
sation on the internal surface of
the headlamp glass is normal ; it
disappears a few minutes after the
lights are switched on .
Model with dipped headlamps with
elliptical module and directional
headlamps
Amber coloured bulbs, such as
the direction indicators, must be
replaced with bulbs of identical
specifi cation and colour.

 Turn the bulb holder one quarter of
a turn and remove it.

 Pull the bulb then change it.
To refi t, carry out these operations in re-
verse order.
Front lights
Blown bulb
A message appears on the multifunc-
tion display to indicate the bulb to be
changed.
Refer to the appropriate procedure to
change the corresponding bulb.
Model with conventional lights

137
Changing the side lights

 Disconnect the main headlamp con-
nector.

 Remove the plastic protective cover
by pulling on the tab.

 Turn the bulb holder one quarter of
a turn and remove it.

 Pull the bulb and change it.
To refi t, carry out these operations in
reverse order.
Changing the dipped headlamps,
main beam headlamps or directional
headlamps

 Disconnect the main headlamp con-
nector.

 Remove the corresponding plastic
protective cover by pulling on the
tab. Changing the integrated direction
indicator side repeaters

 Insert a screwdriver towards the
centre of the repeater between the
repeater and the base of the mirror.

 Tilt the screwdriver to extract the
repeater and remove the repeater.

 Disconnect the repeater connector.
To refi t, carry out these operations in
reverse order.
To obtain a replacement repeater, contact
a PEUGEOT dealer.

 Disconnect the connector of the cor-
responding light.

 Move aside the spring to release the
bulb and remove the bulb.
To refi t, carry out these operations in
reverse order. Changing the fog lamps
For replacement of these bulbs, contact
a PEUGEOT dealer.

ii
138
REAR LIGHTS (SALOON)

1. Brake lights (P21 W).

2. Side lights (R5 W).

3. Fog lamps (P21 W).

4. Direction indicators
(PY 21 W amber).

5. Reversing lights (P21 W). Changing bulbs
These fi ve bulbs are changed from out-
side the boot:

 remove the light fi xing bolt,

 take out the light from the outside,

 disconnect the light connector,

 remove the light seal,

 press the four tabs and remove the
bulb holder,

 turn the bulb one quarter of a turn
and change it.
If the vehicle is fi tted with the JBL
audio system, on the right-hand
side, open the fl ap fi rst to gain ac-
cess to the fi xing bolt.
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifi cation
and colour. To refi t, carry out these operations in
reverse order.

i
140
Rear lights (SW)

1. Brake lights (P21 W).

2. Side lights (R5 W).

3. Direction indicators
(PY 21 W amber).

4. Fog lamps (P21 W).

5. Reversing lights (P21 W). Changing bulbs
These fi ve bulbs are changed from out-
side the boot:

 remove the access fl ap,

 disconnect the light connector,

 remove the light fi xing bolt,

 take out the light from the outside,

 press on the four tabs and remove
the bulb holder,

 turn the bulb a quarter of a turn and
change it.
To refi t, carry out these operations in
reverse order.
Take care to engage the light in its
guides keeping it in the centreline of the
vehicle.
Tighten the fi xing bolt suffi ciently by
hand to guarantee the sealing of the
light.
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifi cation
and colour.