check engine PEUGEOT 207 CC 2011 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2011, Model line: 207 CC, Model: PEUGEOT 207 CC 2011Pages: 224, PDF Size: 7.12 MB
Page 144 of 224

9
!
i
PRACTICAL INFORMATION
142
  Do not charge the batteries without 
disconnecting the terminals fi rst. 
  Do not disconnect the terminals 
while the engine is running. 
  The batteries contain harmful sub-
stances such as sulphuric acid and 
lead. They must be disposed of in 
accordance with regulations and 
must not, in any circumstances, be 
discarded with household waste. 
  Take used remote control batteries 
and vehicle batteries to a special 
collection point. 
   
Charging the battery using a 
battery charger 
   
 
 ) 
  Disconnect the battery from the ve-
hicle. 
   
 ) 
  Follow the instructions for use pro-
vided by the manufacturer of the 
charger. 
   
 ) 
  Reconnect starting with the nega-
tive terminal (-). 
   
 ) 
  Check that the terminals and connec-
tors are clean. If they are covered with 
sulphate (whitish or greenish deposit), 
remove them and clean them.  
  It is advisable to disconnect the 
battery if the vehicle is to be left un-
used for more than one month.    
Before disconnecting the 
battery 
  Wait 2 minutes after switching off 
the ignition before disconnecting 
the battery. 
  Close the windows and the doors 
before disconnecting the battery.  
   
Following reconnection of the 
battery 
  Following reconnection of the bat-
tery, switch on the ignition and wait 
1 minute before starting to permit ini-
tialisation of the electronic systems. 
However, if slight diffi culties are en-
countered following this operation, 
contact a PEUGEOT dealer or a 
qualifi ed workshop. 
  Referring to the corresponding sec-
tion, you must yourself reinitialise: 
   
 
-   the remote control key, 
   
-   the one-touch electric windows, 
   
-   the GPS satellite navigation 
system.  
 
     
 
Disconnecting the cables    
Reconnecting the cables 
   
 
 ) 
  Position the open clip  1 
 of the cable 
on the positive terminal (+) of the 
battery. 
   
 ) 
  Press vertically on the clip  1 
 to posi-
tion it correctly against the battery. 
   
 ) 
  Lock the clip by spreading the position-
ing lug and then lowering the tab  2 
.  
  Do not force the tab as locking will not 
be possible if the clip is not positioned 
correctly; start the procedure again.  
 
   
 
 ) 
  Raise the locking tab fully.  
  
Page 145 of 224

9
!
i
PRACTICAL INFORMATION
143
  A fl at battery prevents the engine 
from starting (refer to the corre-
sponding paragraph).     If a roof operation is in progress, 
it will be completed, but no further 
operation is possible.  
ENERGY ECONOMY MODE 
 
System which manages the duration of 
use of certain functions to conserve a 
suffi cient level of charge in the battery. 
  After the engine has stopped, you can 
still use functions such as the audio 
equipment, windscreen wipers, dipped 
beam headlamps, courtesy lamp, etc. 
for a maximum combined duration of 
thirty minutes. 
Exiting economy mode 
  These functions are reactivated auto-
matically next time the vehicle is driven. 
   
 
 ) 
  In order to resume the use of these 
functions immediately, start the 
engine and let it run for a few minutes.  
  The time available to you will then be 
double the duration for which the engine 
is left running. However, this period will al-
ways be between fi ve and thirty minutes. 
Switching to economy mode 
 
Once the thirty minutes are over, a 
message appears on the multifunction 
screen indicating that the vehicle has 
switched to economy mode and the ac-
tive functions are put on standby. 
CHANGING A WIPER BLADE 
  Procedure for replacing a worn wiper 
blade with a new one without the use 
of tools. 
   
Removing a front wiper blade 
 
 
 
 ) 
  Raise the corresponding wiper arm. 
   
 ) 
  Unclip the wiper blade and remove it.  
 
 
 
Fitting a front wiper blade
 
 
 
 ) 
  Check the size of the wiper blade 
as the shorter blade is fi tted on the 
right-hand side of the vehicle. 
   
 ) 
 Put the corresponding new wiper 
blade in place and clip it. 
   
 ) 
  Fold down the wiper arm carefully.  
 
LOAD REDUCTION MODE 
 
System which manages the use of cer-
tain functions according to the level of 
charge remaining in the battery. 
  When the vehicle is being driven, the load 
reduction function temporarily deactivates 
certain functions, such as the air condi-
tioning, the heated rear screen... 
  The deactivated functions are reactivated 
automatically as soon as conditions permit.