light PEUGEOT 207 CC 2011 Owner's Manual

3
i
ACCESS
66
The vehicle will relock automati-
cally after thirty seconds unless
a door is opened. This system
prevents unintentional unlocking.
The folding and unfolding of the
door mirrors can be deactivated by
a PEUGEOT dealer.

Folding the key


)
First press button A
to fold the key.







Locating your vehicle



)
Press the closed padlock to locate
your locked vehicle in a car park.
This is indicated by lighting of the cour-
tesy lamp and fl ashing of the direction
indicators for a few seconds.
Electronic engine immobiliser
The key contains an electronic chip
which has a special code. When the
ignition is switched on, this code must
be recognised in order for starting to be
possible.
This electronic engine immobiliser locks
the engine management system a few
minutes after the ignition is switched off
and prevents starting of the engine by
anyone who does not have the key.












Anti-theft protection

In the event of a fault, you are
informed by illumination of this
warning lamp, an audible signal
and a message in the screen.
In this case, your vehicle will not start;
contact a PEUGEOT dealer as soon as
possible.
Keep safely the label attached to the
keys given to you on acquisition of the
vehicle.


)
Press the boot unlocking but-
ton on the remote control for
more than 2 seconds. The
boot opens slightly.



Unlocking and partially opening
the boot

3
!
ACCESS
70

Triggering of the alarm

This is indicated by sounding of the si-
ren and fl ashing of the direction indica-
tors for approximately thirty seconds.
After it has been triggered, protection is
again operational.
If the alarm is triggered ten times in
succession, the eleventh time will
result in it becoming inactive.
If the indicator lamp on button A

fl ashes rapidly, this indicates that
the alarm was triggered during
your absence. When the ignition is
switched on, this fl ashing stops im-
mediately.
To avoid triggering the alarm when
washing your vehicle, lock it using
the key in the driver's door lock.


Failure of the remote control



)
Unlock the vehicle using the key in
the driver's door lock.

)
Open the door; the alarm is trig-
gered.

)
Switch on the ignition; the alarm
stops.


*
According to country.


Malfunction

When the ignition is switched on, light-
ing of the indicator lamp on button A
for
ten seconds indicates a siren fault.
Have it checked by a PEUGEOT dealer
or a qualifi ed workshop.


Locking the vehicle without
activating the alarm


)
Lock or deadlock the vehicle using
the key in the driver's door lock.



Automatic operation *

Depending on the legislation in force in
your country, one of these cases may
occur:


- 45 seconds after the vehicle is locked
using the remote control, the alarm is
activated, regardless of the status of
the doors and boot.

- 2 minutes after the last door or the
boot is closed, the alarm is activated.


)
To avoid triggering the alarm on
entering the vehicle, fi rst press the
unlocking button on the remote
control.

Reactivation of the interior
protection


)
Unlock the vehicle using the unlock-
ing button on the remote control.

)
Lock the vehicle again using the re-
mote control.
The alarm is activate again with both
types of protection; the indicator lamp
on button A
fl ashes once per second.

3
!
i
ACCESS
71
WINDOW CONTROLS
System which opens or closes a win-
dow manually or automatically. It is fi t-
ted with a system which controls all four
windows on all models.


1.
Driver's electric windows switch.


2.

Passenger's electric windows switch.


Each window switch controls, on its
own side, the front window and the rear
quarter light.

One-touch electric windows

You have two options:
The windows (except the driver's
window) do not have an automatic
mode or safety anti-pinch function
for closing.
For your safety, the windows rise
in several stages; however, always
be vigilant. The window control switches remain
operational for approximately 45 sec-
onds after the ignition is switched off
or until a door is opened.

)
Press or pull switch 1
. The
window stops as soon as the
switch is released.
The rear quarter light only opens once the
front window has opened completely.

Electric windows



- manual mode




)
Press or pull switch 1
gently. The
window stops as soon as the switch
is released.
The rear quarter light only opens once the
front window has opened completely.


- automatic mode




)
Press switch 1
fully. The window
opens or closes completely when
the switch is released.

)
Pressing the switch again stops the
movement of the window.

)
If you continue to press the switch,
the rear quarter light will open or
close.

3
i
i
ACCESS
76
BOOT

Opening



)
After unlocking the boot or the vehi-
cle using the remote control or the
key, pull the handle and raise the
boot lid.


Unlocking and partially opening
the boot


)
Press the boot unlocking
button on the remote control
for more than two seconds.
The boot opens slightly.

If a battery failure occurs, the boot
is locked. Contact a PEUGEOT
dealer or a qualifi ed workshop.


Boot anti-theft protection

The boot is designed to remain secure,
even in the "cabriolet" confi guration.
So, when the vehicle is locked and the
roof is open, the boot cannot be un-
locked:


- by means of the interior door opening
control, when the key is not in the
ignition switch,

- by pressing the manual centralised
control A
, when the key is not in the
ignition switch.


- when the engine is running
,
this warning lamp comes on,
accompanied by a message
on the multifunction screen for
a few seconds,

- when the vehicle is moving
(speed
above 6 mph (10 km/h)), this warn-
ing lamp comes on, accompanied
by an audible signal and a message
on the multifunction screen for a
few seconds.



Closing



)
Lower the boot lid using the interior
grab handle.
If the boot lid is not closed correctly:
Automatic locking of the boot
In the "cabriolet" confi guration, with
the vehicle locked, if you unlock the
boot by pressing the boot unlock-
ing button on the remote control,
it will lock automatically when you
close it again.
In this case, if you inadvertently
leave the key in the boot, press the
manual centralised control A
im-
mediately to unlock the boot and
retrieve the key.

4
80
VISIBILITY
LIGHTING CONTROL STALK
System for selection and control of the
various front and rear lamps providing
the vehicle's lighting.

Manual controls

The lighting commands are made di-
rectly by the driver by means of ring A

and stalk B
.

A.
main lighting mode selection ring,
with:
Model without AUTO lighting

Model with AUTO lighting
lighting off,
sidelamps only,
dipped or main beam
headlamps,

B.
stalk for inversion of the beam by
pulling:
dipped/main beam headlamps. automatic illumination of
headlamps.

Displays

The corresponding indicator lamp
comes on on the instrument panel to
confi rm the switching on of the lighting
selected.

Main lighting

The vehicle's various front and rear
lamps are designed to adapt the driver's
visibility gradually in relation to the cli-
matic conditions:


- sidelamps, to be seen,

- dipped beam headlamps to see
without dazzling other drivers,

- main beam headlamps for good
visibility when the road is clear.



Additional lighting

Other lamps are installed to respond to
particular driving conditions:


- rear foglamps to be seen from a dis-
tance,

- front foglamps for even better visibility,

- directional headlamps for improved
visibility around corners.



Programmes

Various automatic lighting control modes
are also available according to the fol-
lowing options:


- "guide-me-home" lighting,

- automatic illumination of headlamps,

- static directional lighting. In the lighting off and sidelamps modes,
the driver can switch on the main beam
headlamps directly ("headlamp fl ash")
by pulling and holding the stalk.

4
!
i
81
VISIBILITY

Model with front and
rear foglamps
front and rear foglamps
C.
foglamps selection ring.
These operate with the dipped and main
beam headlamps.


)
To switch on the foglamps, turn
ring C
forwards.

)
To switch off the rear foglamps, turn
ring C
rearwards twice in succession.
When the lighting is switched off auto-
matically (on AUTO model) or when the
dipped beam headlamps are switched
off manually, the foglamps and the side-
lamps will remain on.


)
Turn the ring rearwards to switch
off the foglamps, the sidelamps will
then switch off.
Do not forget to switch off the front
foglamps and the rear foglamps
when they are no longer neces-
sary. In normal light levels, the
power of their beams may dazzle
other drivers.
Lighting on reminder
The triggering of an audible signal
when a door is opened warns the
driver that they have forgotten to
switch off the vehicle's lighting, with
the ignition off.
In this case, switching off the light-
ing will stop the audible signal.
When the ignition is switched off,
if the dipped beam headlamps re-
main on, they will be switched off
automatically after thirty minutes to
prevent discharging of the battery.
This indicator lamp comes on
on the instrument panel.

* According to country.

Daytime running lamps *

On vehicles fi tted with daytime running
lamps, the dipped beam headlamps
come on when the vehicle is started.
The instruments and controls (multi-
function screen, air conditioning control
panel, ...) are not lit, unless the auto-
matic lighting mode is activated or the
lighting is switched on manually.

4
!
82
VISIBILITY
In fog or snow, the sunshine sensor
may detect suffi cient light. There-
fore, the lighting will not come on
automatically.
Do not cover the sunshine sensor,
coupled with the rain sensor and
located in the centre of the wind-
screen behind the rear view mirror;
the associated functions would no
longer be controlled.

Coupling with the "Guide-me-home"
lighting
Association with the automatic illumina-
tion of headlamps provides the "guide-
me-home" lighting with the following
additional options:


- selection of the lighting duration to
15, 30 or 60 seconds in the vehi-
cle parameters in the multifunction
screen confi guration menu,

- automatic activation of "guide-me-
home" lighting when automatic illumi-
nation of headlamps is in operation.











Automatic illumination of headlamps

The sidelamps and dipped beam head-
lamps are switched on automatically, with-
out any action on the part of the driver, when
a low level of external light is detected (sen-
sor behind the rear view mirror) or when the
windscreen wipers are switched on.
As soon as the brightness returns to a suf-
fi cient level or after the windscreen wipers
are switched off, the lighting is switched off
automatically.

"Guide-me-home" lighting

The dipped beam headlamps remain on
temporarily, after switching off the vehi-
cle's ignition, to make the driver's exit
easier in poor light.

Activation


)
With the ignition off, activate a
"headlamp fl ash" using stalk B
.

)
A second "headlamp fl ash" switches
the function off again.


Switching off
The "guide-me-home" lighting is switched
off automatically following the door lock-
ing command, after a given time.


Activation


)
Turn ring A
to the " AUTO
" position.
The automatic illumination of head-
lamps is accompanied by a mes-
sage in the multifunction screen.


Deactivation


)
Turn ring A
to a position other than
" AUTO
". Deactivation is accompa-
nied by a message in the multifunction
screen.

Operating fault
In the event of a malfunction of
the brightness sensor, the light-
ing comes on accompanied by
the service warning lamp, an
audible signal and a message on the
multifunction screen.
Have it checked by a PEUGEOT dealer
or a qualifi ed workshop.

4
i
VISIBILITY
STATIC DIRECTIONAL
LIGHTING
When the dipped or main beam head-
lamps are on, this function enables the
beam to light the inside of the turn with an
additional angle of approximately 30°.
The use of this lighting is optimum above
all at low and average speed (city driving,
winding roads, ...).

with directional lighting


without directional lighting



Programming

Switching on

The system is switched on from a cer-
tain speed and a certain angle of rota-
tion of the steering wheel.


Operating fault

The function is activated or
deactivated via the multi-
function screen confi gura-
tion menu.
This function is activated
by default.
In the event of a malfunction,
this warning lamp fl ashes on
the instrument panel, accom-
panied by a message on the
multifunction screen.
Have it checked by a PEUGEOT dealer
or a qualifi ed workshop.
HEADLAMP ADJUSTMENT

The initial setting is position "0"
. To avoid causing a nuisance to other
road users, the height of the headlamps
should be adjusted in relation to the
load in the vehicle.

0.
1 or 2 people in the front seats.

-.
3 people.

1.
4 people.

2.
4 people + maximum authorised load.

3.
Driver + maximum authorised load.


Switching off

The system is switched off below a certain
angle of rotation of the steering wheel.
It is switched off when reverse gear is
engaged.

4
i
i
84
VISIBILITY
WIPER CONTROL STALK
System for the selection and control of
the various windscreen wiping modes
permitting the dispersal of rain and
cleaning.
The vehicle's windscreen wipers are
designed to gradually improve the driv-
er's visibility in relation to the weather
conditions.


Manual controls

The wiping commands are made directly
by the driver using stalk A
.
fast (heavy rain),
normal (moderate rain),
intermittent (in proportion to
the speed of the vehicle),
off,
single wipe (press downwards),
Model with intermittent wiping

Windscreen wipers


A.
wiping speed selection control:










Windscreen and headlamp
wash


)
Pull the windscreen wiper stalk to-
wards you. The screenwash then the
wipers operate for a fi xed period.
The headlamp wash is only activate if
the dipped headlamps are on
.
With daytime running lamps, to
activate the headlamp wash, posi-
tion the lighting stalk in the dipped
beam position.
On vehicles fi tted with digital air
conditioning, any action on the
windscreen wash control results in
temporary closing of the air intake
to avoid odours inside the passen-
ger compartment. Automatic wiping is not available
on the 207CC at present.

4
i
85
VISIBILITY


Special position of the windscreen
wipers
In the minute following switching off of
the ignition, any action on the stalk po-
sitions the wipers vertically on the wind-
screen.
This action enables you to position the
wiper blades for winter parking.
To park the wipers after this has been
done, switch on the ignition and operate
the stalk.
COURTESY LAMP



A.
Courtesy lamp


B.
Map reading lamps

In this position, the courtesy
lamp comes on gradually:

Map reading lamps



)
With the ignition on, press the cor-
responding switch.
With the "permanent lighting" mode,
the duration of lighting varies, de-
pending on the circumstances:


- with the ignition off, approxi-
mately ten minutes,

- in energy economy mode, ap-
proximately thirty seconds,

- with the engine running, unlimited.




- when the vehicle is unlocked,

- when the key is removed from the
ignition,

- when a door is opened,

- when the remote control locking but-
ton is activated, in order to locate
your vehicle.
It switches off gradually:


- when the vehicle is locked,

- when the ignition is switched on,

-
30 seconds after the last door is closed.

Permanently off.
Permanent lighting.


Courtesy lamp