seats Peugeot 207 Dag 2007.5 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2007.5, Model line: 207 Dag, Model: Peugeot 207 Dag 2007.5Pages: 223, PDF Size: 9.01 MB
Page 7 of 223
i
FAMILIARISATION
Also...
5. Access to the rear seats
( 3 - d o o r ) .
6. A r m r e s t ( e x c e p t 3 - d o o r ) .
7. Heated seat.
Front seat adjustment
Steering wheel adjustment
1. F o r w a r d s - b a c k w a r d s a d j u s t m e n t .
2. H e i g h t a d j u s t m e n t .
3. S e a t b a c k a n g l e a d j u s t m e n t .
4. Head restraint height and angle
a d j u s t m e n t .
49
1. Unlocking the control.
2. H e i g h t a n d d e p t h a d j u s t m e n t .
3. Locking the control.
56
Page 50 of 223
49
FRONT SEATS
Seat consisting of a seat cushion, seat
back and head restraint which can all
be adjusted to adapt your position for
maximum ease of driving and comfort.
1. F o r w a r d s - b a c k w a r d s a d j u s t m e n t
Lift the control and slide the seat for-
wards or backwards. 2. Driver's or passenger's seat
h e i g h t a d j u s t m e n t
Pull the handle upwards or push it
downwards as many times as ne-
cessary to obtain the required posi-
tion. 3.
S e a t b a c k a n g l e a d j u s t m e n t
Push the handle towards the rear.
Page 51 of 223
!
!
50
No person or object must prevent
the seat slide from returning to its
initial position; return to this posi-
tion is necessary for the seat to
lock in place.
Take care not to trap the seat belt
to avoid hindering the passage of
the rear passengers.
4. Access to rear seats
(3 door)
Pull the handle to fold the seat back
and move the seat forwards. On re-
positioning, the seat returns to its
initial position. 5. Head restraint height and angle
a d j u s t m e n t
To raise the head restraint, pull it up-
wards.
To remove the head restraint, press
the lug A and pull the head restraint
upwards.
To put the head restraint back in po-
sition, locate the stems of the head
restraint in the holes, taking care to
keep them in line with the seat back.
To lower the head restraint, press
the lug A and the head restraint at
the same time.
To tilt the head restraint, tilt the low-
er part forwards or rearwards. The head restraint has a frame with
a notch which prevents the head
restraint from lowering; this is a
safety device which provides pro-
tection in the event of an impact.
T h e a d j u s t m e n t i s c o r r e c t w h e n
the upper edge of the head
restraint is level with the top of
the head.
Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
Page 52 of 223
!
i
51
REAR SEATS
Bench seat the left-hand part (2/3) or
right-hand part (1/3) of which can be
folded to adapt the load space in the
boot. Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
As the head restraints are not inter-
changeable, take care to put them
back in their original position when
r e i t t i n g ( G T i ) .
Rear head restraints
These have a high position (comfort)
and a low position (rear visibility).
The command for activation of heat-
ing of the seat(s) remains memorised
for two minutes after the ignition has
been switched off.
7. Heated seats switch
With the engine running, the front seats
can be heated separately.
Use the adjustment dial, placed on
the side of each front seat, to switch
on and select the level of heating re-
quired:
0 : Off.
1 : Low.
2 : Medium.
3 : High.
They can also be removed; to remove
them:
pull the head restraint upwards to
the stop,
then, press the lug.
6. Armrests (except 3 door)
These can be folded down and are re-
movable.
To remove them, press the button
located between the armrest and
the side of the seat and pull it.
Page 53 of 223
!
i
51
REAR SEATS
Bench seat the left-hand part (2/3) or
right-hand part (1/3) of which can be
folded to adapt the load space in the
boot. Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
As the head restraints are not inter-
changeable, take care to put them
back in their original position when
r e i t t i n g ( G T i ) .
Rear head restraints
These have a high position (comfort)
and a low position (rear visibility).
The command for activation of heat-
ing of the seat(s) remains memorised
for two minutes after the ignition has
been switched off.
7. Heated seats switch
With the engine running, the front seats
can be heated separately.
Use the adjustment dial, placed on
the side of each front seat, to switch
on and select the level of heating re-
quired:
0 : Off.
1 : Low.
2 : Medium.
3 : High.
They can also be removed; to remove
them:
pull the head restraint upwards to
the stop,
then, press the lug.
6. Armrests (except 3 door)
These can be folded down and are re-
movable.
To remove them, press the button
located between the armrest and
the side of the seat and pull it.
Page 55 of 223
!
i
51
REAR SEATS
Bench seat the left-hand part (2/3) or
right-hand part (1/3) of which can be
folded to adapt the load space in the
boot. Never drive with the head restraints
removed; they must be in place and
correctly adjusted.
As the head restraints are not inter-
changeable, take care to put them
back in their original position when
r e i t t i n g ( G T i ) .
Rear head restraints
These have a high position (comfort)
and a low position (rear visibility).
The command for activation of heat-
ing of the seat(s) remains memorised
for two minutes after the ignition has
been switched off.
7. Heated seats switch
With the engine running, the front seats
can be heated separately.
Use the adjustment dial, placed on
the side of each front seat, to switch
on and select the level of heating re-
quired:
0 : Off.
1 : Low.
2 : Medium.
3 : High.
They can also be removed; to remove
them:
pull the head restraint upwards to
the stop,
then, press the lug.
6. Armrests (except 3 door)
These can be folded down and are re-
movable.
To remove them, press the button
located between the armrest and
the side of the seat and pull it.
Page 56 of 223
!
i
53
Folding the seat (SW)
This operation can be carried out at the
rear seats or through the opening rear
screen.
To fold a rear seat without any risk of
damage:
move the corresponding front seat
forward if necessary,
place the head restraints in the low
position, Check that no object could hinder
the movement of the bench seat,
either above or below.
Repositioning the seat (SW) The seat cushion lowers in order to
be covered by the seat back; this
q u i c k l y e n a b l e s y o u t o b e n e i t f r o m
a l a t b o o t l o o r .
pull the control 1 forward to release
the seat back 2 which folds easily
onto the seat cushion 3 .
When repositioning the rear seat,
straighten the seat back 2 and lock it.
Check that the red indicator, located
at control 1 , is no longer visible.
Page 64 of 223
i
61
Hooks Hooked onto the stowing rings, this ena-
bles you to secure your luggage, either
to the bottom of the boot or to the back
of the rear seats.
Rear shelf (Saloon)
To remove the shelf:
unhook the two cords,
raise the shelf slightly, then remove it. The hooks permit the securing of shop-
ping bags. Luggage retaining net
When changing a wheel
The hooks permit easy access to
the spare wheel by retaining the
boot carpet by means of its cord.
You have two storage options:
- either upright behind the front seats,
- or upright behind the rear seats.
Page 66 of 223
i
63
Load space cover (SW)
This consists of three sections which
can be folded back on each other.
To store it, fold it on itself and place it
vertically at the back of the boot.
To fold it from the boot:
take hold of the load space cover by
its strap A ,
fold it concertina-style to the rear
seats.
To unfold it from the boot:
take hold of the load space cover by
its strap A ,
unfold it to the boot pillars.
To gain access from the rear seats:
raise the front section of the load
space cover using the handle B . 12 V accessories socket (SW)
In order to connect a 12 V accesso-
ry (max power: 120 Watts), remove
the cap and connect the appropriate
adaptor.
Turn the key to the ignition position.
Maximum loads
7.5 kg, load space cover unfolded
with high load retaining net at row 2.
Page 67 of 223
i
64
High load retaining net (SW)
H o o k e d o n t o t h e u p p e r i x i n g s a n d o n t o
the ISOFIX rings or the lugs, this per-
mits use of the entire loading volume up
to the roof:
- behind the rear seats (row 2),
- behind the front seats (row 1) when the rear seats are folded.
To use it in row 1:
o p e n t h e c o v e r s o f t h e u p p e r i x i n g s 1 ,
unroll the high load retaining net,
position one of the ends of the net's
metal bar in the corresponding up-
p e r i x i n g 1 , then do the same with
the other end,
slacken the straps fully,
i x t h e s n a p h o o k o f e a c h o f t h e s t r a p s
on the corresponding lug 3 , located
under the bench seat cushion,
fold the rear seats,
tighten the straps without raising the
bench seat,
check that the net is hooked and
tightened correctly. To use it in row 2:
fold or remove the load space cover,
o p e n t h e c o v e r s o f t h e u p p e r i x i n g s 2 ,
unroll the high load retaining net,
position one of the ends of the net's
metal bar in the corresponding up-
p e r i x i n g 2 , then do the same with
the other end,
attach the hook of each of the net's
straps in the corresponding ISOFIX
ring 4 ,
tighten the straps,
check that the net is hooked and
tightened correctly.
When positioning the net, check
that the strap loops are visible from
the boot; this will make slackening
or tightening easier.