display Peugeot 207 Dag 2009 Owner's Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2009, Model line: 207 Dag, Model: Peugeot 207 Dag 2009Pages: 267, PDF Size: 20.02 MB
Page 81 of 267
i
88
STATIC DIRECTIONAL
LIGHTING
When the dipped or main beam head-lamps are on, this function enables the beam to light the inside of the turn with an additional angle of approximately 30°.
The use of this lighting is optimum above all at low and average speed (city driving, w i n d i n g r o a d s , . . . ) .
with directional lighting
Programming
Switching on
The system is switched on from a certain speed and a certain angle of rotation of the steering wheel.
Operating fault
The function is activated or deactivated via the multi- f u n c t i o n d i s p l a y c o n fi g u r a -tion menu.
By default, this function is activated.
In the event of a malfunction, t h i s w a r n i n g l i g h t fl a s h e s o n t h e instrument panel, accompanied by a message on the multifunc-tion display.
Have it checked by a PEUGEOT dealer.
Switching off
The system is switched off below a certain angle of rotation of the steering wheel.
It is switched off when reverse gear is engaged.
HEADLAMP ADJUSTMENT
To avoid causing a nuisance to other road users, the height of the headlamps should be adjusted in relation to the load in the vehicle.
0. 1 or 2 people in the front seats.
-. 3 people.
1. 5 people.
2. 5 people + maximum authorised load.
3. Driver + maximum authorised load. without directional lighting
Page 84 of 267
!
i
91
Special position of the windscreen wipers Automatic windscreen wiping
The windscreen wipers operate auto-
matically, without any action on the part
of the driver, if rain is detected (sensor
b e h i n d t h e i n t e r i o r m i r r o r ) , a d a p t i n g t h e i r
speed to the intensity of the rainfall.
Activation
This is controlled manually by the driver
by pushing the stalk A to the "AUTO"
position.
It is accompanied by a message on the
multifunction display.
In the minute following switching off of the ignition, any action on the stalk posi-tions the wipers in the centre of the windscreen.
This action enables you to position the wiper blades for winter parking.
To park the wipers after this has been done, switch on the ignition and operate the stalk.
Do not cover the rain sensor, cou-
pled with the brightness sensor and
located in the centre of the wind-
screen behind the interior mirror.
Switch off the ignition when using
an automatic car wash.
In winter, it is advisable to wait until
the windscreen is completely clear
of ice before activating the auto-
matic wiping. The automatic wiping must be re-
activated if the ignition has been off
for more than one minute, by push-
ing the stalk
A downwards.
Switching off
This is controlled manually by the driver
by moving the stalk A to another posi-
tion and returning it to position "0" .
It is accompanied by a message on the
multifunction display. Operating fault
If an automatic wiping malfunction oc-
curs, the wipers will operate in intermit-
tent mode.
Have it checked by a PEUGEOT dealer.
Page 97 of 267
!
CHILD SAFETY
103
MANUAL CHILD LOCK
Mechanical system to prevent opening of the rear door using its interior control.
The control is located on the edge of each rear door.
T u r n t h e r e d c o n t r o l o n e q u a r t e r o f a turn to the right using the ignition key.
ELECTRIC CHILD LOCK
Remote control system to prevent open i n g o f t h e r e a r d o o r s u s i n g t h e i r i n -terior controls.
The control is located in the centre of the fascia.
Press button A .
The indicator light on button A comes on, accompanied by a message on the multifunction display.
Locking
Unlocking
T u r n t h e r e d c o n t r o l o n e q u a r t e r o f a turn to the left using the ignition key.
Activation
Deactivation
Press button A again.
The indicator light on button A switches off, accompanied by a message on the multifunction display.
Page 100 of 267
!
i
i
i
SAFETY
106
TYRE UNDER-INFLATION
DETECTION
System which automatically checks the pressure of the tyres while driving.
S e n s o r s fi t t e d i n e a c h v a l v e t r i g g e r a warning in the event of malfunction (speed above 12 mph (20 km/h).
Flat tyre
A message appears on the multifunc-tion display, accompanied by an audible signal, to locate the wheel concerned.
Check the tyre pressures as soon as possible.
This check must be carried out when the tyres are cold.
This warning light and the STOPwarning light come on on the instrument panel, accompanied by an audible signal and a mes-sage on the multifunction display locating the wheel concerned.
Stop immediately, avoiding any sud-den movement of the steering wheel and the brakes.
Change the damaged wheel (punc- t u r e d o r v e r y d e fl a t e d t y r e ) , a n d have the tyre pressure checked as soon as possible.
Puncture
Sensor(s) not detected or faulty
A message appears on the multifunc-tion display, accompanied by an audi-ble signal, to locate the wheel or wheels which are not detected or to indicate a fault in the system.
Contact a PEUGEOT dealer to replace the faulty sensor(s).
Page 102 of 267
!
SAFETY
108
The ESP/ASR systems offer ex-
ceptional safety in normal driving,
but this should not encourage the
driver to take extra risks or drive at
high speed.
The correct functioning of these
systems depends on observation
of the manufacturer's recommen-
dations regarding the wheels (tyres
and rims), the braking components,
the electronic components and the
PEUGEOT assembly and opera-
tion procedures.
After an impact, have these systems
checked by a PEUGEOT dealer.
Disarming
In exceptional conditions (starting a
vehicle which is bogged down, stuck
in snow, on soft ground, ...), it may be
advisable to disarm the ASR and ESP
systems, so that the wheels can move
freely and regain grip.
Press the "ESP OFF" button, locat-
ed in the centre of the fascia.
If this warning light comes on on
the instrument panel and the in-
dicator light on the button comes
on, this indicates that the ASR and
ESP systems are disarmed.
Reactivation
These systems are reactivated automat-
ically each time the ignition is switched
b a c k o n o r f r o m 3 0 m p h ( 5 0 k m / h ) ( e x -
cept in the case of the 1.6 l 16V THP
175 bhp petrol engine).
Press the "ESP OFF" button again
to reactivate them manually.
Operating fault
If this warning light comes on,
accompanied by an audible sig-
nal and a message on the multi-
function display, this indicates a
malfunction of these systems.
Have them checked by a PEUGEOT dealer.
TRAJECTORY CONTROL
SYSTEMS
Activation
These systems are activated automati-
cally each time the vehicle is started.
Anti-skid regulation (ASR) and
electronic stability programme
(ESP)
They come into operation in
t h e e v e n t o f a g r i p o r t r a j e c t o r y
problem.
T h i s i s i n d i c a t e d b y fl a s h i n g o f
this warning lamp on the instru-
ment panel. Steering/ESP coupling system
(SSP)
The anti-skid regulation (also known as
Traction Control) optimises traction to
prevent skidding of the wheels, by act-
ing on the brakes of the driving wheels
and on the engine.
The electronic stability programme acts
on the brake of one or more wheels and
on the engine to keep the vehicle on the
t r a j e c t o r y r e q u i r e d b y t h e d r i v e r . This system optimises the stability of
the vehicle and its braking capacity by
combining the actions of the ESP and
electric power steering when braking on
surfaces on which the grip of the right-
hand and left-hand wheel differs.
It permits increased braking of the
wheels which are in contact with the
section of road offering the higher level
of grip and, anticipating the instability of
the vehicle, the application of a slight
correction to the turning angle of the
wheels to assist the driver in maintain-
i n g h i s t r a j e c t o r y .
Page 104 of 267
SAFETY
110
1. Front left seat belt warning light.
2. Front right seat belt warning light.
3. Rear left seat belt warning light.
4. Rear centre seat belt warning
light ** .
5. Rear right seat belt warning light.
On the central bar, the corresponding
warning light 1 or 2 comes on in red if
the seat belt is not fastened or is unfas-
tened.
When the engine is running, the corre-
sponding warning light 1 or 2 comes on
in red, accompanied by an audible signal
and a message on the multifunction dis-
play, if a front occupant has unfastened
his seat belt.
Seat belt not fastened/unfastened
warning lights bar
Rear seat belts
T h e r e a r s e a t s a r e fi t t e d w i t h t h r e e s e a t
belts ** , each with three anchoring points
and an inertia reel with force limiter. Seat belt unfastened warning lights
bar
When the ignition is switched on,
the corresponding warning lights
3,
4 ** and 5 come on for approximately
3 0 s e c o n d s i n r e d i f t h e s e a t b e l t i s n o t
fastened.
When the engine is running, the corre-
sponding warning light 3, 4 ** or 5 comes
on in red, accompanied by an audible
signal and a message on the multifunc-
tion display, if a rear passenger has un-
fastened his seat belt.
Fastening
Pull the strap, then insert the tongue
in the buckle.
Check that the seat belt is fastened
correctly by pulling the strap.
Unfastening
Press the red button on the buckle.
** Except GTi.
Page 107 of 267
!
!
SAFETY
1 1 3
If both air bag warning lights come
on continuously, do not install a
"rear facing" child seat on the front
passenger seat.
Have the system checked by a
PEUGEOT dealer.
Operating fault
If this warning light comes on on
the instrument panel, accompa-
nied by an audible warning and
a message on the multifunction
display, contact a PEUGEOT dealer to
have the system checked. The air bags
may no longer be triggered in the event
of a serious impact.
To guarantee the safety of your
child, it is imperative that the pas-
senger air bag is disarmed when
you install a "rear facing" child seat
on the front passenger seat.
Otherwise, the child would risk be-
i n g s e r i o u s l y i n j u r e d o r k i l l e d i f t h e
air bag were triggered.
According to version, this warn-
ing light comes on either on
the instrument panel or on the
central bar when the ignition is
on and until the air bag is re-
armed. Reactivation
When you remove the child seat, turn
switch
1 to the "ON" position to re-arm
the air bag and so guarantee the safety
of your front passenger in the event of
an impact.
Deactivation
Only the front passenger's air bag can
be disarmed:
with the ignition off , insert the key
in the passenger air bag disarming
switch 1 ,
turn it to the "OFF" position,
then, remove the key keeping the
switch in this position.
Page 111 of 267
i
117
* According to engine.
GEAR CHANGE INDICATOR *
System which reduces fuel consump-
tion by advising the driver to change up
a g e a r o n v e h i c l e s fi t t e d w i t h a m a n u a l
gearbox.
Operation
The system acts solely in the context of
economical driving.
Depending on the driving situation and
your vehicle's equipment, the system
may advise you to skip one or more
gears. You can follow this instruction with-
out engaging the intermediate gears.
The gear engagement recommenda-
tions must not be considered compulsory.
I n f a c t , t h e c o n fi g u r a t i o n o f t h e r o a d , t h e
a m o u n t o f t r a f fi c a n d s a f e t y r e m a i n d e t e r -
mining factors when choosing the best
gear. Therefore, the driver remains re-
sponsible for deciding whether or not to
follow the advice given by the system.
This function cannot be deactivated. Example:
- You are in third gear.
The information appears in the form of an
arrow on the instrument panel display. In the case of driving which makes
particular demands on the perfor-
m a n c e o f t h e e n g i n e ( fi r m p r e s -
sure on the accelerator pedal, for
example, when overtaking...), the
system will not recommend a gear
change.
The system never suggests:
- e n g a g i n g o f fi r s t g e a r ,
- engaging of reverse gear,
- engaging of a lower gear.
- You press the accelerator pedal
moderately.
- The system may suggest that you engage a higher gear, if appropriate.
Page 113 of 267
i
i
i
119
Instrument panel displays
Gear lever positions
N Neutral
R Reverse
1, 2, 3, 4, 5 Gears in sequential mode
AUTO.
This comes on when the automated
mode is selected. It switches off on
changing to sequential mode.
In the automated mode, if the gear-
box detects poor grip, this warning
light comes on. Moving off Sequential mode
After starting the vehicle, select
position M to change to sequential
mode.
Automated mode
Following use of the sequential
mode, select position A to return to
the automated mode.
When stopping on a slope, do not
use the accelerator to immobilise
the vehicle; apply the handbrake.
When moving off on a slope, accel-
erate gradually while releasing the
handbrake.
Place your foot on the
brake when this warning
l i g h t fl a s h e s ( e . g . : s t a r t i n g
the engine).
Select position N .
Press the brake pedal.
Start the engine.
N appears on the instrument panel.
N fl a s h e s o n t h e i n s t r u m e n t p a n e l
display if the gear lever is not in po-
sition N on starting.
S e l e c t fi r s t g e a r ( p o s i t i o n M or A ) or
reverse (position R )
Release the handbrake.
Take your foot off the brake pedal,
then accelerate.
AUTO and 1 or R appear on
the instrument panel.
AUTO disappears and the gears
engaged appear in succession
on the instrument panel.
The gear change requests are only car-
ried out if the engine speed permits.
When driving at low speed, on ap-
p r o a c h i n g a s t o p s i g n o r t r a f fi c l i g h t s f o r
example, the gearbox changes down to
fi r s t g e a r a u t o m a t i c a l l y .
AUTO and the gear engaged
appear on the instrument panel.
The gearbox then operates in auto-
adaptive mode, without any action on
the part of the driver. It continuously se-
lects the most suitable gear in relation
to the following parameters:
- driving style,
- road conditions,
- vehicle load.
When reverse gear is engaged, an
audible signal is triggered.
Page 114 of 267
!
i
120
"Auto sequential" mode
In the automated mode, you can resume
control temporarily at any time using the
steering wheel controls.
The use of these controls permits man-
ual selection of the gears in situations
which require a more rapid change-
down than in the automated mode (ar-
rival at a roundabout, leaving a car park
with a steep gradient, overtaking...).
The gearbox engages the required gear if
the engine speed permits. AUTO remains
displayed on the instrument panel.
After a few minutes, the gearbox re-
sumes automatic control of the gears. "Snow" automated mode
In the automated mode, if the vehi-
cle detects poor grip, the gearbox will
change automatically to the "snow" au-
tomated mode.
Stopping the vehicle
Before switching off the engine, you can
change to position
N to be in neutral.
In this case, it is imperative that you
apply the handbrake to immobilise the
vehicle.
Reinitialisation
Following disconnection of the battery,
the gearbox must be reinitialised.
Switch on the ignition. Operating fault
With the ignition on, if this warn-
ing light comes on and AUTO
fl a s h e s , a c c o m p a n i e d b y a n a u -
dible signal and a message on
the multifunction display, this indicates
a gearbox malfunction.
Have it checked by a PEUGEOT dealer.
It is compulsory to press the brake
pedal while starting the engine.
Never select neutral N while the
vehicle is moving.
Only engage reverse gear R when
the vehicle is immobilised, with
your foot on the brake pedal.
In all cases, it is imperative that you
apply the handbrake to immobilise
the vehicle.
If you press the accelerator pedal
beyond the point of resistance, the
gearbox selects the gear below to
permit sharper acceleration.
AUTO and appear on the
instrument panel.
AUTO , and - appear on the
instrument panel.
Select position N .
Press the brake pedal.
Wait approximately 30 seconds until
N or a gear appears on the instru-
ment panel.
Release the brake pedal.
The gearbox is operational again.