Main menu Peugeot 208 2015 Owner's Manual

1
31
208_en_Chap01_instruments-bord_ed01-2016
F Select the "Driving" menu.
F

S

elect the desired tab using your finger.
Touch screen
F Press the MENU button to
display the main menu. Successively:
Current information
Range
(miles or km)
The distance that can be
travelled using the remaining
fuel in the tank (based on the
average fuel consumption over
the last few miles).
Once the remaining range is below 20 miles

(30 km), dashes are displayed. After topping-up
with at least 5 litres of fuel, the range is recalculated
and displayed if it exceeds 60 miles (100 km).
Current fuel consumption
(l/100 km or km/l or mpg)
Calculated over the last few seconds.
Stop & Star t time counter
(if function present)
(In minutes
/ seconds -
hours
/ minutes)
This function is only displayed above
20

mph (30 km/h).
This value can vary following a change
in driving conditions or the relief of the
road, giving rise to a big difference in
current fuel consumption.
If dashes instead of figures continue
to be displayed when driving, contact
a PEUGEOT dealer or a qualified
workshop. If your vehicle has Stop & Start, a time counter
records the periods in STOP mode during a
j o u r n ey.
It is reset to zero every time the ignition is
switched on using the key.
Instruments

33
208_en_Chap01_instruments-bord_ed01-2016
Date and time
Press MENU to display the " MAIN
MENU ".
Select "Adjust time " or "Adjust date".
Touch screen
Select " Settings ".
In the secondary page, select " Time/
Date ".
Select "
Secondary page ".
Modify the setting using the virtual keypad then
confirm.Press "Confirm " to save and quit.
Instrument panel
F Each press of this button moves between
the following settings:
-
hours,
-


minutes,
-

1
2 or 24 hour format.
1
Instruments

34
208_en_Chap01_instruments-bord_ed01-2016
Lighting dimmer
Tw o b u t t o n s
With the exterior lighting on:
One button
F Press this button to increase the brightness. F
P ress this button to
adjust the brightness,
F

P
ress this button to
reduce the brightness. F

r
elease the button when the desired level is
reached.
As soon as the lighting reaches the required
level of brightness, release the button. System for the manual adjustment of the
brightness of the instrument panel and the
touch screen to suit the ambient light level.
With the vehicle lighting off or in day
mode (daytime running lamps on),
pressing the button has no effect.
Touch screen
F Select " Screen settings" .
F Press
MENU

to display the "MAIN
MENU" .
F Select
"Settings" .
F Select
"Secondary page" .
Adjustment
F

A

djust the brightness by moving the cursor.
Instruments

79
The sidelamps and dipped beam headlamps are
switched on automatically, without any action
on the part of the driver, when a low level of
ambient light is detected or in certain cases of
activation of the windscreen wipers.
As soon as the brightness returns to a sufficient
level or after the windscreen wipers are switched
off, the lamps are switched off automatically.
AUTO mode
On
F Turn the ring to the "AUTO" position.
Activation of the function is accompanied
by a message in the screen.
Off
F Turn the ring to another position. Deactivation of the function is
accompanied by a message in the screen.
Automatic guide-me-home
lighting
Association with the automatic lighting provides
the guide-me-home lighting with the following
additional options:
-

s
election of the lighting duration of 15, 30
or 60 seconds,
-

a
utomatic activation of guide-me-home
lighting when the automatic illumination of
headlamps is in operation. In the event of a fault with the
sunshine sensor, the lighting comes
In fog or snow, the sunshine sensor
may detect sufficient light. In this
case, the lighting will not come on
automatically.
Do not cover the sunshine sensor,
coupled with the rain sensor and
located in the centre of the windscreen
behind the rear view mirror; the
associated functions would no longer
be controlled.
Configuration
Press "MENU" to display the "MAIN
MENU" .
Select "Driving" .
Select "Secondary page" .
Select the "Driving assistance" tab.
Activate the "Guide me home"
function. Select "Vehicle settings" .Switching off
Switching on Deactivate the "Guide me home"

function.
on, this warning lamp is displayed in the
instrument panel and/or a message appears in
the screen, accompanied by an audible signal.
Contact a PEUGEOT dealer or a qualified
workshop.
4
Lighting and visibility

86
With the dipped or main beam headlamps
on, this function makes use of the beam from
the front foglamp to illuminate the inside of a
bend, when the vehicle speed is below 25 mph
(approximately 40 km/h) (urban driving, winding
road, intersections, parking manoeuvres...).
Cornering lighting
With cornering lighting Without cornering lighting
Activation
The system operates:
- w hen the corresponding direction indicator
is switched on,
or
-

f
rom a certain angle of rotation of the
steering wheel.
Programming
The system is activated or
deactivated in the vehicle
configuration menu.
The system is activated by default.
Deactivation
The system does not operate:
- b elow a certain angle of rotation of the
steering wheel,
-

a
bove 25 mph (40 km/h),
-
w

hen reverse gear is engaged.
Lighting and visibility

88
Rear
If a significant accumulation of snow or
ice is present, or when using a bicycle
carrier on the boot, deactivate the
automatic rear wiper via the vehicle
configuration menu.Park.
Intermittent wipe.
Wash-wipe (set duration).
Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation if the windscreen
wipers are operating. On
Press "MENU" to display the " MAIN
MENU ".
Select "Driving" .
Select "Secondary page" .
Select "Vehicle settings" .
Select the "Driving assistance" tab.
Activate the "Auto rear wiper in
reverse" function.
Configuration
This function is activated by default.
Off
Deactivate the "Auto rear wiper in reverse"
function.
The automatic rain sensitive windscreen
wipers must be reactivated by pushing
the control stalk downwards, if the
ignition has been off for more than
1


minute.
Do not cover the rain sensor, linked with
the sunshine sensor, located at the top
of the windscreen behind the rear view
m i r r o r.
Switch off the automatic rain sensitive
wipers when using an automatic car wash.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic rain
sensitive wipers.
Single wipe
Pull the stalk briefly towards you.
Unusual operation
If the wipers operate in intermittent mode when
in AUTO mode, have the system checked by a
PEUGEOT dealer or a qualified workshop.
Lighting and visibility

Driving139
208_en_Chap06_conduite_ed01-2016
Speed settings
F Go to the main menu by pressing the " MENU " button.
F

Sel
ect the " Driving" menu.
F

Sel
ect the secondary page.
F

Sel
ect "Speed settings ".
F

Sel

ect the speed to be modified.
F

P

ress on " Modify". As a safety measure, the driver must
only carry out these operations when
stationary.
F

E
nter the new value.
F Pr ess on confirm.
F C onfirm to save the modifications and quit
the menu.
Use this button to select all speeds.
Use this button to deselect all
speeds.
This button restores the factory
settings.
The speed values applied by the speed limiter
"
LIMIT " and the cruise control " CRUISE" can
be saved (up to 5 different speed settings).
With the touch screen
Advice
6

Driving
142
208_en_Chap06_conduite_ed01-2016
The collision can be automatically
avoided if the speed difference between
your vehicle and the one ahead is not
more than 9 mph (15 km/h).
Above this threshold, the system will do
what is possible to avoid or reduce the
seriousness of the accident by lowering
the speed of impact.
The automatic braking triggered:
-

c

an be even more effective if the driver
presses the brake pedal more firmly,
-

m

ay stop the vehicle, holding the brakes on
for 1.5 seconds when stationary to allow
the driver time to take back control of the
vehicle,
-

m

ay cause the engine to stall,
-

m

ay give rise to a pumping noise, due to
the pressurisation of the braking system.
Touch screen
Press " MENU" to display the " MAIN
MENU ".
Select " Driving ".
Select " Secondary page ".
Select " Vehicle settings ".
Select the " Driving assistance " tab.
Check the " Automatic emergency
braking activated " box.
Activation
Confirm. Deactivation
Check the "
Automatic emergency braking
deactivated " box.
The last selection remains in memory when the
ignition is switched off.
If the automatic emergency braking function is
deactivated, following each start a temporary
message will be displayed to signal this, once a
speed threshold (6 mph - 10 km/h) is exceeded.
To deactivate :
- F ollowing an impact to the windscreen
close to the sensor.
-

W
hen towing a trailer.
-
W

hen the vehicle is being towed.
-

W
hen the vehicle is about to cross a toll
payment barrier.
-

W
hen the vehicle is going through an
automatic car wash.

Practical information175
208_en_Chap07_informations-pratiques_ed01-2016
Advice
While the quantity of AdBlue® in the additive
t
ank is sufficient, no information is displayed.
On the other hand, once the additive level
drops to the quantity needed for a range of
1 500 miles (2 400 km) driving, you are warned
by different temporary signals (warning lamp,
message, audible signal).
When the AdBlue
® tank is empty, restarting
becomes impossible. Different levels of alert are triggered according
to the remaining driving range threshold.
You will be informed as each mileage threshold
is reached and the alerts will change from
temporary to permanent.
-
T he 1st alert is triggered at a remaining
driving range of 1 500 miles (2 400 km).
-

T

he 2
nd alert is triggered at a remaining
driving range of 375 miles (600 km).
Up to 0 miles, at which point it will be
impossible to restart the engine after a stop.
Range indicators
It is strongly recommended that you do
not wait for the successive alerts before
topping-up the AdBlue
® tank, but do this
as soon as possible.
Driving range
Press this button to display the information.
With the touch screen:
If the range is greater than 3 100 miles
(5 000 km), a range value is not given. -

s
elect the "Driving assistance"
menu,
-
s

elect "Diagnostic",
-

s
elect CHECK.
7

271
208_en_Chap10b_SMEGplus_ed01-2016
As a safety measure and because it
requires sustained attention by the
driver, using a smartphone when
driving is prohibited.
All operations must be done with the
vehicle stationary.
The synchronisation of a
smartphone allows applications on a
smartphone that are adapted to the
MirrorLink
TM technology to be displayed
i
n the vehicle's screen.
The principles and standards
are constantly evolving. For the
communication process between the
smartphone and the system to work
correctly, the smartphone must be
unlocked; update the operating system
of your smartphone as well as the date
and time in the smartphone and the
system.
For the list of eligible smartphones,
connect to the brand's internet website
in your country. As a safety measure, applications
can only be viewed with the vehicle
stationary; display is interrupted once
the vehicle is moving.When connecting a smartphone to
the system, it is recommended that
Bluetooth
® be started on the smartphone.
Start the application on the
smartphone (optional, depending
on the smartphone and operating
syste m).
Access to the different audio sources remains
accessible in the margin of the MirrorLink
TM
display, using touch buttons in the upper bar.
Access to the menus for the system is possible
at any time using the dedicated buttons During the procedure, several screen
pages relating to certain functions
are displayed.
Accept to start and end the
connection.
Connect a USB cable. The
smartphone charges when
connected by a USB cable. Press on " MirrorLink
TM" to
start the application in the
system. Once connection is established, an page
is displayed with the applications already
downloaded to your smartphone and adapted
to MirrorLink
TM technology.
If only one application has been downloaded to
the smartphone, it starts automatically.
MirrorLinkTM smartphone
connection
Press the end of the lighting control stalk to
start voice recognition of your smartphone via
the system.
Voice recognition requires a compatible
smartphone connected to the vehicle by
Bluetooth.
Voice recognition
Please note:
-
i f your smartphone is supported, to
make it "MirrorLink
TM" compatible,
some phone manufacturers
nevertheless invite you to first
download a dedicated application.
From the system, press on
" Connected services " to display the
primary page.
10
Audio and Telematics