Peugeot 208 2017 Owner's Manual

169
Main beam headlamps
F Disconnect the main headlamp connector.
F R emove the protective cover by pulling on
the tab.
F

D
isconnect the bulb connector.
F

P
ull the bulb out and change it.
To reassemble, carry out these operations in
reverse order, positioning the alignment lug at
the bottom.
Daytime running lamps/
sidelamps
F Turn the bulb holder a quarter turn and pull it out.
F

P
ull out the bulb and replace it.
To refit, carry out these operations in reverse
o r d e r.
Daytime running lamps /
sidelamps (light emitting diodes
– LEDs)
For the replacement of this type of diode lamp,
contact a PEUGEOT dealer or a qualified
workshop.
8
In the event of a breakdown

170
Foglamps / directional lamps
F Access to the front foglamp is through the aperture below the bumper.
F

D
isconnect the bulb holder connector by
pressing on the top of the tongue.
F

E
xtract the bulb holder by pressing on the
two clips (top and bottom).
F

R
eplace the module.
To refit, carry out these operations in
reverse order.
Contact a PEUGEOT dealer or a qualified
workshop to obtain the module.
You can also contact a PEUGEOT
dealer or a qualified workshop for the
replacement of these bulbs.
Integrated direction indicator
side repeaters
F Insert a flat screwdriver between the door mirror glass and its base.
F

T
ilt the screwdriver and use it as a lever to
extract the glass.
F

U
nclip the shell of the door mirror by
pressing on the two fixing clips.
F

P
ress the central tongue and remove the
side repeater.
F

P
ull out the bulb holder and replace the
faulty bulb. To refit, carry out these operations in
reverse order.
To replace this type of bulb, you can also
contact a PEUGEOT dealer or a qualified
workshop.
Rear lamps
1.
Brake lamps (light emitting diodes –
LEDs).
2. Reversing lamps (P21W).
3. Direction indicators (PY21W amber)
4. Sidelamps (light emitting diodes –
LEDs).
In the event of a breakdown

171
5.Foglamp (P21W).
Light- emitting diodes – LEDs
For replacement, contact a PEUGEOT
dealer or a qualified workshop.
Reversing lamps and direction
indicators
These two bulbs are changed from inside the
boot:
F

O
pen the boot. F

R
emove the access grille from the
corresponding side trim panel.
F
U
nscrew and remove the nut.
F
D
isconnect the lamp unit connector.
F
U
nclip the lamp unit and carefully extract it
pulling straight towards you.
F
P
ress the four tabs and remove the bulb
h o l d e r.
F

T
urn the bulb a quarter turn, pull it out and
fit a new bulb. To reassemble, proceed in reverse order.
Make sure to engage the lamp unit in its guides
while keeping it in line with the vehicle.
Tighten sufficiently to ensure sealing, but
without damaging the lamp.
Third brake lamp
F Unscrew the fixing pins on each side of the
lamp, without removing them completely.
F

P
ush on the screws to unclip the lamp unit.
F

D
isconnect the lamp unit connector.
F

R
emove the lamp unit from the outside.
F

T
urn the bulb holder corresponding to the
faulty lamp a quarter turn and pull it out.
F

P
ull the bulb out and change it.
To reassemble, proceed in reverse order.
8
In the event of a breakdown

172
Licence plate lamps
For easier removal, per form this procedure with
the tailgate half open.
F
I
nsert a thin screwdriver into the cut-out
located outside the lens.
F

P
ush it outwards.
F

R
emove the lens.
F

C
hange the faulty bulb.
To refit, press on the lens to clip it in place.
Foglamp
For access, pass your hand under the bumper.
F T urn the bulb holder a quarter turn and pull
it out.
F

D
isconnect the lamp unit connector.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
To replace this type of bulb, you can also
contact a PEUGEOT dealer or a qualified
workshop.
Changing a fuse
Access to the tools
The extraction tweezers are fitted to the back
of the dashboard fusebox cover or glovebox.
Dashboard
F Unclip the cover by pulling at the top left, then right.
F

D
isengage the cover completely and turn it
ove r.
F

R
emove the carrier on which the tweezers
are fitted.
In the event of a breakdown

173
Glove box
F Open the glove box lid.
F U nclip the fusebox cover by pulling at the
top right.
F

D
isengage the cover completely and turn it
ove r.
F

R
emove the carrier on which the tweezers
are fitted. Before changing a fuse, it is necessary that:
F

t
he vehicle must be stationary with the
ignition off,
F
s
witch off all electrical consumers,
F
t
he defective fuse must be identified using
the allocation tables and the diagrams in the
following pages.
To work on a fuse, you must:
F
u
se the special tweezers to extract the fuse
from its housing and check the condition of
its filament,
F
a
lways replace the defective fuse with a
fuse of the same rating (same colour); using
a different rating could cause a malfunction
(risk of fire).
If the fault recurs after replacing a fuse, have
the electrical system checked by a PEUGEOT
dealer or a qualified workshop.
The fuse allocation tables and
corresponding diagrams are available on
the website:
http://public.servicebox.peugeot.com/ddb/
You can go to a PEUGEOT dealer or a
qualified workshop.OK
Failed
Tw e e z e r s
Professional repairers: for full information
on the fuses and relays, consult the wiring
information and diagrams available at a
PEUGEOT dealer.
The replacement of a fuse not shown in
the allocation tables opposite may cause
a serious malfunction of your vehicle.
Contact a PEUGEOT dealer or a qualified
workshop.
8
In the event of a breakdown

174
Installing electrical
accessories
Your vehicle's electrical system is
designed to operate with standard or
optional equipment.
Before installing other electrical
equipment or accessories on your vehicle,
contact a PEUGEOT dealer or a qualified
workshop.
PEUGEOT accepts no responsibility for
the cost incurred in repairing your vehicle
or for rectifying malfunctions resulting
from the installation of accessories
not supplied and not recommended by
PEUGEOT and not installed in accordance
with specifications, in particular when the
combined power consumption of all of the
additional equipment connected exceeds
10

milliamperes.
On the left
Fuse no. Rating Functions
F1 (GPL) 10 AIgnition + (positive).
F2 5 AExterior mirrors, headlamps, diagnostic socket.
F9 5 AAlarm.
F10 5 AIndependent telematic unit, trailer interface unit.
F11 5 AElectrochrome interior rear-view mirror, additional
heating.
F13 5 AHi-Fi amplifier, parking sensors.
F16 15 AFront 12
V socket.
F17 15 AAudio system, after-market audio system.
F18 20 ATouch screen.
In the event of a breakdown

175
Fuse no.Rating Functions
F23 5 ACourtesy mirrors, map reading lamp.
F26 15 AHorn.
F27 15 AScreenwash pump.
F28 5 AAnti-theft.
F29 15 AAir conditioning compressor.
F30 15 ARear wiper.
8
In the event of a breakdown

176
On the rightFuse no.Rating Functions
F01 40 AHeated rear window.
F02 10 AHeated door mirrors.
F03 30 AFront one-touch windows.
F04 -Not used.
F05 30 ARear one-touch windows.
F06 10 AFolding door mirrors.
F07 10 AFolding door mirrors.
F08 -Not used.
F09 15 AFront heated seats.
F10 20 AHi-Fi amplifier.
F11 -Not used.
F12 -Not used.
In the event of a breakdown

177
Underbonnet
The fusebox is placed in the engine
compartment near the battery (left-hand side).
Access to the fuses
F Unclip the cover.
F C hange the fuse.
F

W
hen you have finished, close the cover
very carefully to ensure correct sealing of
the fusebox. Fuse no.
Rating Functions
F16 15 AFront foglamps.
F18 10 ARight-hand main beam headlamp.
F19 10 ALeft-hand main beam headlamp.
F25 30 AHeadlamp washer relay (after-market).
F26 (GPL) 20 ABattery + (positive).
F29 40 AFront wiper motor.
8
In the event of a breakdown

178
12 V battery
Batteries contain harmful substances
such as sulphuric acid and lead.
They must be disposed of in
accordance with regulations and must
not, in any circumstances, be discarded
with household waste.
Take used remote control batteries and
vehicle batteries to a special collection
point.
Procedure for starting the engine using another
battery or charging a discharged battery.
General points
Lead-acid starter batteries
Protect your eyes and face before
handling the battery.
All operations on the battery must be
carried out in a well ventilated area and
away from naked flames and sources of
sparks, so as to avoid the risk of explosion
or fire.
Wash your hands afterwards.
Access to the battery
The battery is located under the bonnet.
To gain access:
F

O
pen the bonnet using the interior release
lever, then the exterior safety catch.
F

S
ecure the bonnet stay.
F

R
emove the plastic cover on the (+)
terminal.
The battery (-) terminal is not accessible. A
remote earth point is located on the engine.
Starting using another
battery
Never try to start the engine by connecting
a battery charger.
Never use a 24
V or higher battery
b o o s t e r.
Check beforehand that the backup
battery has a nominal voltage of 12
V and
a capacity at least equal to that of the
discharged battery.
The two vehicles must not be in contact
with each other.
Switch off all the electrical consumers
on both vehicles (audio system, wipers,
lighting, etc.).
Make sure that the jump leads are not
close to moving parts of the engine (fan,
belts, etc.).
Do not disconnect the (+) terminal while
the engine is running.
When your vehicle's battery is discharged, the
engine can be started using a backup battery
(external or from another vehicle) and jump
leads or a battery booster.
In the event of a breakdown