stop start Peugeot 208 2017 Owner's Guide

148
Checking levels
Check all of these levels regularly, in line with
the manufacturer's service schedule. Top them
up if necessary, unless other wise indicated.
If a level drops significantly, have the
corresponding system checked by a PEUGEOT
dealer or a qualified workshop.The fluid must comply with the
manufacturer's recommendations and with
the vehicle's engine.
Take care when working under the bonnet,
as certain areas of the engine may be
extremely hot (risk of burns) and the
cooling fan could start at any time (even
with the ignition off).
Used products
Avoid prolonged contact of used oil or
fluids with the skin.
Most of these fluids are harmful to health
or indeed very corrosive. Do not discard used oil or fluids into
sewers or onto the ground.
Take used oil to a PEUGEOT dealer
or a qualified workshop and dispose
of it in the containers reser ved for this
purpose.
Engine oil level
The check is carried out either when
the ignition is switched on using the
oil level indicator in the instrument
panel for vehicles equipped with an
electric gauge, or using the dipstick.
To ensure that the reading is correct, your
vehicle must be parked on a level sur face
with the engine stopped for more than
30


minutes.
It is normal to top up the oil level between
two ser vices (or oil changes). PEUGEOT
recommends that you check the level, and top
up if necessary, every 3,000
miles (5,000 km).
Checking using the dipstick
The location of the dipstick is shown in the
corresponding underbonnet layout view.
F
T
ake the dipstick by its coloured grip and
pull it out completely.
F

W
ipe the end of the dipstick using a clean
non-fluffy cloth.
F

R
efit the dipstick and push fully down, then
pull it out again to make the visual check:
the correct level is between marks A and B .
A = MA X
B = MIN
If you find that the level is above the A mark or
below the B mark, do not star t the engine.
-

I
f the level is above the MAX mark (risk of
damage to the engine), contact a PEUGEOT
dealer or a qualified workshop.
-

I
f the level is below the MIN mark, you must
top up the engine oil.
Practical information

150
Screenwash fluid level
Top up to the required level when
necessary.
Fluid specification
The screenwash fluid must be topped up with a
ready for use mix.
In winter (temperatures below zero), a liquid
with antifreeze must be used that is appropriate
for the prevailing conditions, in order to
preser ve the elements of the system (pump,
tank, ducts, etc.).
Filling with pure water is prohibited under all
circumstances (risk of freezing, limestone
deposits, etc.).
Diesel fuel additive level
(Diesel with particle filter)
The additive reser voir low level is
indicated by fixed illumination of this
warning lamp, accompanied by an
audible signal and a message that
the particle filter additive level is
too low.
To p p i n g u p
The reser voir must be topped up without delay
by a PEUGEOT dealer or a qualified workshop.
Level of AdBlue
An alert is triggered once the reser ve level is
reached.
To avoid the vehicle being immobilised as per
regulations, you must top up with AdBlue.
For more information on AdBlue
® and the SCR
system, and in particular topping it up, refer to
the corresponding section.
Checks
Unless otherwise indicated, check these
components in accordance with the
manufacturer's service schedule and according
to your engine.
Other wise, have them checked by a PEUGEOT
dealer or a qualified workshop.
12 V battery
The battery does not require any
maintenance.
However, check regularly that the
terminals are correctly tightened
(versions without quick release terminals)
and that the connections are clean.
For more information and the precautions
to take before starting work on the 12 V
battery , refer to the corresponding
section.
Versions equipped with Stop & Start are
fitted with a 12
V lead-acid battery of
specific technology and specification.
Its replacement should be carried out
only by a PEUGEOT dealer or a qualified
workshop.
Practical information

155
Refilling
Important: if your vehicle's AdBlue®
tank is completely empty – which is
confirmed by the alert messages and the
impossibility of starting the engine – you
must add at least 4

litres and no more than
10


litres. F

A
fter emptying the container or bottle, wipe
away any spillage around the tank filler
using a damp cloth.
If any fluid is spilt or splashed, wash
immediately with cold water or wipe with a
damp cloth.
If the fluid has crystallised, clean it off
using a sponge and hot water.
After refilling
Through the boot (1.6 litre
BlueHDi Euro 6.1)
F Refit the blue cap to the tank filler and turn it
a 6th of a turn clockwise, to its stop.
F
R
efit the black cap and turn it a quarter of a
turn clockwise without pressing. Check that
the cap indicator lamp is facing the support
indicator lamp.
F

D

epending on equipment, return the spare
wheel and/or the storage box to the bottom
of the boot.
F

R

efit the boot carpet and close the tailgate.
Through the fuel filler flap
(1.5 litre BlueHDi Euro 6.2)
F Refit the blue cap to the tank filler and turn it
a 6th of a turn clockwise, to its stop.
F
C
lose the fuel filler flap.
F

O

btain an AdBlue
® container or bottle. After
first checking the use-by date, read the
instructions on the label carefully before
pouring the contents of the container or
bottle into your vehicle's AdBlue
® tank.
7
Practical information

179
F Lift the plastic cover on the (+) terminal, if your vehicle has one.
F

C
onnect the red cable to the positive
terminal (+) of flat battery A (at the metal
elbow) then to the positive terminal (+) of
backup battery B or the booster.
F

C
onnect one end of the green or black
cable to the negative terminal (-) of backup
battery B or the booster (or an earth point
on the other vehicle).
F

C
onnect the other end of the green or black
cable to earth point C on the broken down
vehicle.
F

S
tart the engine of the vehicle with the
good battery and leave it running for a few
minutes.
F

O
perate the starter on the broken down
vehicle and let the engine turn.
If the engine does not start straight away,
switch off the ignition and wait a few moments
before trying again. F

W
ait until the engine returns to idle then
disconnect the jump lead cables in the
reverse order.
F
R
efit the plastic cover to the (+) terminal, if
your vehicle has one.
F
A
llow the engine to run for at least
30 minutes, by driving or with the vehicle
stationary, so that the battery reaches an
adequate state of charge.
Some functions, including Stop & Start,
are not available if the battery is not
sufficiently charged.
Charging the battery using
a battery charger
For optimum ser vice life of the battery, it is
essential to maintain an adequate state of
charge.
In some circumstances it may be necessary to
charge the battery:
-

i
f you only use your vehicle for short
journeys,
-

i
f the vehicle is to be taken off the road for
several weeks.
Contact a PEUGEOT dealer or a qualified
workshop. If you plan to charge your vehicle's battery
yourself, use only a charger compatible
with lead-acid batteries of a nominal
voltage of 12
V.
Follow the instructions provided by the
manufacturer of the charger.
Never reverse polarities.
It is not necessary to disconnect the
battery.
F
S
witch off the ignition.
F
S
witch off all electrical consumers (audio
system, lighting, wipers, etc.).
8
In the event of a breakdown

180
F Switch off the charger B before connecting the cables to the battery, so as to avoid any
dangerous sparks.
F

E
nsure that the charger cables are in good
condition.
F

R
aise the plastic cover, if your vehicle has
one, on the (+) terminal.
F

C
onnect the charger B cables as follows:
-

t
he positive (+) red cable to the (+)
terminal of the battery A ,
-

t
he negative (-) black cable to the earth
point C on the vehicle.
F

A
t the end of the charging operation, switch
off the charger B before disconnecting the
cables from the battery A .
Some functions, including Stop & Start,
are not available if the battery is not
sufficiently charged.
If this label is present, it is essential to
use only a 12
V charger to avoid causing
irreversible damage to the electrical
components related to the Stop & Start
system. Never try to charge a frozen battery – risk
of explosion!
If the battery has frozen, have it checked
by a PEUGEOT dealer or by a qualified
workshop who will check that the internal
components have not been damaged and
that the container has not cracked, which
would mean a risk of toxic and corrosive
acid leaking.
Disconnecting the battery
In order to maintain an adequate state
of charge for starting the engine, it is
recommended that the battery be disconnected
if the vehicle is taken out of ser vice for a long
period.
Before disconnecting the battery:
F

c
lose all openings (doors, boot, windows,
roof),
F

s
witch off all electrical consumers (audio
system, wipers, lighting, etc.),
F

s
witch off the ignition and wait for four
minutes.
At the battery, detach the (+) terminal only.
Quick-release terminal clamp
Disconnecting the (+) terminal
F Raise lever A fully to release clamp B .
F R emove clamp B by lifting it off.
In the event of a breakdown

181
To w i n gReconnecting the (+) terminal
F Raise lever A fully.
F R efit open clamp B on the (+) terminal.
F

P
ush clamp B fully down.
F

L
ower lever A to lock clamp B .
Do not force the lever as locking will not
be possible if the clamp is not positioned
correctly; start the procedure again.
Following reconnection of the
battery
Following reconnection of the battery, switch on
the ignition and wait 1 minute before starting to
permit initialisation of the electronic systems. If
minor problems nevertheless persist following
this operation, contact a PEUGEOT dealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise (depending on
version):
-

t
he remote control key,
-
etc.The Stop & Start system may not be
operational during the trip following the
first engine start.
In this case, the system will only be
available again after a continuous
period of immobilisation of the vehicle,
a period which depends on the exterior
temperature and the state of charge of the
battery (up to about 8 hours). Procedure for having your vehicle towed or for
towing another vehicle using the towing eye.
8
In the event of a breakdown

8
Voice commandsHelp messages
Navigate home To start guidance or add a stopover, say
"navigate to" and then the address or contact
name. For example, "navigate to address 11
Regent Street, London", or "navigate to contact,
John Miller". You can specify if it's a preferred
or recent destination. For example, "navigate
to preferred address, Tennis club", "navigate to
recent destination, 11 Regent Street, London".
Other wise, just say, "navigate home". To see
points of interest on a map, you can say things
like "show hotels in Banbury" or "show nearby
petrol station". For more information you can
ask for "help with route guidance".
Navigate to work
Navigate to preferred address <...>
Navigate to contact <…>
Navigate to address <...>
Show nearby POI <...>
Remaining distance
To get information about your current route,
you can say "tell me the remaining time",
"distance" or "arrival time". Try saying "help
with navigation" to learn more commands.
Remaining time
Arrival time
Stop route guidance
Depending on the country, give the
destination instructions (address) in the
language used by the system."Radio Media" voice
commands
These commands can be made from any
screen page after pressing the " Voice
command" or "Telephone" button located
on the steering wheel, as long as there is
no telephone call in progress.
PEUGEOT Connect Nav

15
The "USB peripheral error" or "Peripheral not
recognised" message appears on the screen.The USB memory stick is not recognised. Use only USB memory sticks formatted to FAT
32 (28 -bit file allocation table).
A telephone connects automatically,
disconnecting another telephone. Automatic connection overrides manual
connection.Modify the telephone settings to remove
automatic connection.
The iPod is not recognised when connecting to
the USB port. The iPod is of a generation that is not
compatible with the USB.
The hard disk or device is not recognised when
connecting to the USB socket. Some hard disks and devices need a power
supply greater than is provided by the audio
system.Connect the peripheral to the 230
V socket, the
12 V socket or an external power supply.
Caution : ensure that the device does not
transmit a voltage greater than 5
V (risk of
destruction of the system).
When streaming, the sound cuts momentarily. Some telephones prioritise connection of the
"hands-free" profile.Delete the "hands-free" connection profile to
improve streaming.
In "Random all" play, not all of the tracks are
played. In "Random all" play, the system can only take
into account up to 999 tracks.
With the engine off, the audio system switches
off after a few minutes of use. When the engine is switched off, the audio
system operating time depends on the battery
charge.
The switch-off is normal: the audio system
switches to economy mode and switches off to
prevent discharging the vehicle's battery.Start the vehicle’s engine to increase the battery
charge.
The message "the audio system is overheated"
appears on the display. In order to protect the installation if the
surrounding temperature is too high, the audio
system switches to an automatic thermal
protection mode leading to a reduction of the
volume or stopping of the playing of the CD.Switch the audio system off for a few minutes to
allow the system to cool.
.
Audio system / Bluetooth®

10
In "Random all" play, not all of the tracks are
played.In "Random all" play, the system can only take
into account up to 999 tracks.
With the engine off, the audio system switches
off after a few minutes of use. When the engine is switched off, the audio
system operating time depends on the battery
charge.
The switch-off is normal: the audio system
switches to economy mode and switches off to
prevent discharging the vehicle's battery.Start the vehicle’s engine to increase the battery
charge.
The message "the audio system is overheated"
appears on the display. In order to protect the installation if the
surrounding temperature is too high, the audio
system switches to an automatic thermal
protection mode leading to a reduction of the
volume or stopping of the playing of the CD.Switch the audio system off for a few minutes to
allow the system to cool.
Audio system

198
S
Safety, children ..........85, 88-90 , 93, 95 , 97-10 0SCR (Selective Catalytic Reduction) system .....15 2Screen, instrument panel ..........................3 0 - 31
Screen menu map ........................................... 13
Screenwash


.................................................... 74
Screenwash, rear


............................................ 74
Seat, rear bench


............................................. 53
Seat belts


............................................ 81- 83, 94
Seats, front
...............................

...........48, 50-52
Seats, heated


.................................................. 51
Seats, rear


................................................. 53-54
Serial number, vehicle


..................................192
Service indicator


............................................. 24
Servicing
................................................. 24,

104
Settings, system


........................................ 35, 19
Sidelamps
............................. 67,

70 -71, 167-171
Side repeater


................................................ 170
Snow chains


.................................................. 141
Socket, 12
V accessory ..................................64
Socket, auxiliary
........................................ 26,

10
Socket, JACK


...................................... 64, 26 , 10
Sockets, audio
............................................ 64,

5
Sockets, auxiliary
...............................

...............5
Speed limiter
.................................. 12

1-123, 126
Stability control (ESC)..................................... 78
Starting a Diesel engine
............................... 14

0
Starting the engine
......... 10

5, 108 -109, 112-115
Starting using another battery


......................178
Station, radio
...............................

..23-25 , 7, 3 , 3
Stay, bonnet


........................................... 145 -14 6
Steering mounted controls, audio
................ 3,

3
Steering wheel, adjustment
............................ 46
S

top (warning lamp)

........................................ 11
Stop & Start


.....................
21, 33 , 55 , 60, 11 8 -12 1 ,
131 , 13 8, 145 , 15 0, 181Storage ...................................................... 52, 63
Stowing rings .................................................. 65
Switching off the engine


...............105, 108 -109
Synchronising the remote control
.............38-39
T
Tables of fuses ....................... 17 2, 174 , 176 -17 7
Ta n k , f u e l ................................................ 13 8 -13 9
Telephone
..............................

........28-33 , 15 -18
Temperature, coolant


...................................... 23
Textured Paint


............................................... 15 6
Third brake lamp


........................................... 171
Three flashes (direction indicators)
.......... 6

8-69
Time (setting)


................................ 33-34, 36, 20
TMC (Traffic info)

............................................ 14To o l s .......162, 162-163 , 172, 174, 176 -17 7 , 182-183Touch screen ......................................... 13 6, 1, 1
To w b a r ............................... .............10 6 -107, 142
Towed loads


.................................................. 18 4
To w i n g


.................................................... 181-183
Traction control (ASR)


........................15, 78- 80
Traffic information (TA)


.....................................4
Traffic information (TMC)


................................14
Tr a i l e r
...............

.............................. 10 6 -107, 142
Triangle, warning ........................................... 157
Trip computer


............................................ 30-33
Ty r e s


...................................................... 104, 193
Tyre under-inflation detection ......15, 13 5 -13 6 , 161
U
Under-inflation (detection) ............................13 5
Unlocking ........................................................ 36
Unlocking from the inside
...............................40
Unlocking the boot

...............................
.....4 0 - 41
Updating the date
............................... 33,

36, 20
Updating the time
.......................... 33

-34, 36 , 20
USB


......................................... 26-27, 1 0 -11 , 5, 5
V
Ventilation ................................... 55-57, 60, 104
Voice commands ......................................... 5 -10
W
Warning and indicator lamps ..........................10
W arning lamp, braking system .......................11
Warning lamp, Diesel engine pre-heater


.......21
Warning lamp, Service ....................................20
Warning lamp, Stop


........................................ 11
Warning lamps


................................................ 10
Weights
...............

..................18 4 -185, 188, 19 0
Wheel, spare
...............................

...162-163 , 193
Window controls


....................................... 43-44
Wiper, rear ....................................................... 74
Wiper blades (changing)


...............................14 4
Wipers


................................................. 22, 72-73
Wipers, automatic rain sensitive


.....................73
Alphabetical index