turn signal Peugeot 208 2018 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2018, Model line: 208, Model: Peugeot 208 2018Pages: 240, PDF Size: 7.73 MB
Page 20 of 240
18
Warning/indicator lampStateCause Actions/Observations
+
+ SCR emissions
control system
Fixed when the ignition is
switched on, accompanied
by an audible signal and
a
message.A fault with the SCR emissions
control system has been detected. This alert disappears once the exhaust emissions
return to normal levels.
AdBlue
® warning
lamp flashing, on
switching on the
ignition, associated
with the fixed Ser vice
and Engine-diagnostic
warning lamps,
accompanied by an
audible signal and
a
message indicating
the remaining driving
range. Depending on the message
displayed, you can continue driving
for up to 685
miles (1,100 km) before
the engine starting prevention system
is triggered. Carry out (3) as soon as possible to avoid star ting
being prevented
.
AdBlue
® warning
lamp flashing, on
switching on the
ignition, associated
with the fixed Ser vice
and Engine-diagnostic
warning lamps,
accompanied by an
audible signal and
a
message. An engine immobiliser prevents
the engine from restarting (over
the authorised driving limit after
confirmation of a
fault with the
emissions control system). To start the engine, carry out (2).
Rear foglamp Fixed. The lamp is on.
Instruments
Page 26 of 240
24
Starting preventedYou have exceeded the authorised driving
limit: the starting prevention system does
not allow the engine to be started.
To be able to restart the engine, you must call
on a
PEUGEOT dealer or a qualified workshop.
Each time the ignition is switched on, these
warning lamps come on and the AdBlue
warning lamp flashes, accompanied by an
audible signal and the display of the message
"Emissions fault: Starting prevented".
Trip computer
Instrument panel screen
F Each press on the end of the wiper
control stalk displays the information in
turn. -
Trip
1 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the first trip.
- Trip
2 with:
•
t
he average speed,
•
t
he average fuel consumption,
•
t
he distance travelled,
for the second trip.
-
T
he current information with:
•
t
he range,
•
t
he current fuel consumption,
•
t
he Stop & Start time counter.
With touch screen
The information is accessible via the
Driving/Vehicle
.
Reset trip
F When the desired trip is displayed, press
the button located on the end of the wiper
control stalk for more than 2
seconds.
Trips 1
and 2 are independent and are used
identically.
For example, trip 1
can be used for daily figures
and trip 2
for monthly figures.
Display of information on the touch screen
Instruments
Page 33 of 240
31
F Turn the key towards the rear again within 5 seconds to deadlock the vehicle.
Lighting of the direction indicators for a
few
seconds confirms that the procedure has
completed correctly.
If your vehicle is fitted with an alarm, this
function will not be activated when locking
with the key.
If the alarm is activated, the siren sounds
on opening the door; switch on the ignition
to stop it.
Central locking not
functioning
Use these procedures in the following cases:
- c entral locking fault,
-
b
attery disconnected or discharged.
In the event of a
malfunction with the
central locking system, the battery must
be disconnected to lock the boot and thus
ensure that the vehicle is locked fully.
Driver's door
F Turn the key towards the rear of the vehicle to lock it, or towards the front to unlock it.
Passenger doors
Unlocking
F P ull the interior door opening handle.
Locking
F
O
pen the door.
F
F
or the rear doors, check that the child lock
is not activated. Refer to the corresponding
section.
F
R
emove the black cap, located on the edge
of the door, using the key.
F
I
nsert the key into the hole without forcing
it; then, without turning it, move the latch
sideways towards the inside of the door.
F
R
emove the key and refit the black cap.
F
C
lose the doors and check from the
outside that the vehicle is locked.
Changing the battery
If the battery is flat, you are informed
by illumination of this warning lamp,
an audible signal and a
message in
the screen. Batter y ref.: CR1620/3
volts.
F
U
nclip the cover by inserting a small
screwdriver in the slot and raise the cover.
F
R
emove the discharged battery from its
housing.
F
I
nsert the new battery, observing the
polarity, and clip the cover onto the
housing.
F
R
einitialise the remote control.
For more information on Reinitialising the
remote control , refer to the corresponding
section.
Do not throw remote control batteries
away as they contain metals which are
harmful to the environment. Take them
to an approved collection point.
2
Access
Page 54 of 240
52
If the lighting is switched off automatically
(version with AUTO lighting) or the dipped
beams are switched off manually, the foglamps
and sidelamps remain on.
F
T
urn the ring rear wards to switch the
foglamps off; the sidelamps will then switch
of f.
In good or rainy weather, by day and
night, using the front and rear foglamps is
prohibited. In these situations, the power
of their beams may dazzle other drivers.
They should only be used in fog or falling
snow.
In these weather conditions, it is your
responsibility to switch on the foglamps
and dipped beam headlamps manually as
the sunshine sensor may detect sufficient
light.
Do not forget to turn off the front and rear
foglamps as soon as they are no longer
necessary.
Switching off of the lighting when the
ignition is switched off
On switching off the ignition, all of the
lighting turns off immediately, except for
dipped beam if automatic guide-me-home
lighting is activated. Switching on the lighting after the
ignition is switched off
To reactivate the lighting control stalk, set
the ring to position "
0" - lighting off, then to
the desired position.
On opening the driver's door, a
temporary
audible signal warns the driver that the
lighting is on.
The lamps, with the exception of the
sidelamps, switch off automatically after
a
maximum duration of 30 minutes to
prevent discharging of the battery.
Direction indicators
F Lower the lighting control stalk fully when turning left.
F
R
aise the lighting control stalk fully when
turning right. If you forget to cancel the direction
indicators for more than 20
seconds, the
volume of the audible signal will increase if
the speed is above 37 mph (60 km/h).
Three flashes
Move the stalk briefly upwards or downwards,
without going beyond the point of resistance;
the corresponding direction indicators will flash
three times.
This function can be used at any speed,
but it is particularly useful for changing
lane on fast roads.
Automatic illumination of
headlamps
When a low level of ambient light is detected by
t he sunshine sensor, the number plate lamps,
sidelamps and dipped beam headlamps are
switched on automatically, without any action
on the part of the driver. They may also come
on if rain is detected, at the same time as
automatic operation of the windscreen wipers.
As soon as the brightness returns to
a
sufficient level or after the windscreen wipers
are switched off, the lamps are switched off
automatically.
Lighting and visibility
Page 55 of 240
53
Switching on
F Turn the ring to the "AUTO" position.
Activation of the function is accompanied by
a
message on the screen.
Switching off
F Turn the ring to another position. Deactivation of the function is accompanied
by a
message in the screen.
In fog or snow, the sunshine sensor may
detect sufficient light. In this case, the
lighting will not come on automatically.
Do not cover the sunshine sensor, linked
with the rain sensor and located in the
centre of the windscreen behind the rear
view mirror; the associated functions
would no longer be controlled.
Automatic guide-me-home
lighting
When associated with automatic illumination of
headlamps, the guide-me-home lighting offers
the following additional options:
-
s
election of the lighting duration of 15, 30 or
60
seconds,
-
a
utomatic activation of guide-me-home
lighting when the automatic illumination of
headlamps is in operation.
The guide-me-home lighting can be
configured in the Driving/Vehicle
menu.
In the event of a
fault with the
sunshine sensor, the lighting comes
on, this warning lamp is displayed
in the instrument panel and/or
a
message appears on the screen,
accompanied by an audible signal.
Contact a
PEUGEOT dealer or
a
qualified workshop.
Manual guide-me-home
lighting
Temporarily keeping the dipped beam
headlamps on after the vehicle's ignition has
been switched off makes the driver's exit easier
when the light is poor.
Switching on
F With the ignition off, "flash" the headlamps using the lighting control stalk.
F
A f
urther "headlamp flash" switches the
function off.
Manual guide-me-home lighting is
also available from the remote control
lighting button.
Switching off
Manual guide-me-home lighting goes off
automatically at the end of a given period of
time.
4
Lighting and visibility
Page 56 of 240
54
Headlamp beam height
adjustment
To avoid causing a nuisance to other road
u sers, the height of the headlamp beams
should be adjusted according to the load in the
vehicle.
0. 1
or 2 people in the front seats.
-. Intermediate setting.
1. 5
people.
-. 5
people + maximum authorised load.
2. Driver + maximum authorised load.
The initial setting is position " 0".
Vehicle side marking by illumination of the
sidelamps on the traffic side only.
F
W
ithin one minute after switching off the
ignition, operate the lighting control stalk up
or down, depending on the traffic side (for
example, when parked on the left, move the
lighting control stalk upwards; the right-hand
sidelamps come on).
This is confirmed by an audible signal and
illumination of the corresponding direction
indicator lamp in the instrument panel.
To switch off the parking lamps, return the
lighting control stalk to the middle position or
switch on the ignition.
Parking lamps Daytime running lamps/
Sidelamps
The front and rear lamps light up automatically
when the engine starts.
They provide the following functions:
-
D
aytime running lamps (lighting control
stalk at position " 0" or " AUTO " with
adequate light level).
-
S
idelamps (lighting control stalk at " AUTO"
position with low light levels or "Sidelamps
only" or "Dipped/main beam headlamps").
The LEDs are brighter when operating as
daytime running lamps.
Lighting and visibility
Page 63 of 240
61
Anti-lock braking system
(ABS) and electronic brake
force distribution (EBFD)
The fixed illumination of this warning
lamp indicates that there is a fault
with the ABS.
The vehicle retains conventional braking. Drive
carefully at moderate speed. If these warning lamps come on,
accompanied by an audible signal
and a
message, this indicates a fault
with the electronic brake force
distribution (EBFD) system.
When changing wheels (tyres and rims),
ensure that these are approved for your
vehicle.
Normal operation of the ABS may make
itself felt by slight vibration of the brake
pedal. If you need to brake in an emergency,
press the brake pedal ver y firmly and
keep the pressure applied.
You must stop as soon as it is safe to do so.
In both cases, have the system checked by
a
PEUGEOT dealer or a qualified workshop as
soon as possible.Anti-slip regulation (ASR)/
Dynamic stability control
(DSC)
Operation
These systems are activated automatically
every time the vehicle is started.
They come into operation in the event of
a
problem with grip or trajectory. This is indicated by flashing of this
warning lamp in the instrument panel.
Deactivation
In exceptional conditions (starting a vehicle
w hich is bogged down, stuck in snow, on soft
ground, etc.), it may be advisable to deactivate
these systems, so that the wheels can turn
freely and regain grip.
Reactivate these systems as soon as the level
of grip permits.
Deactivation of ASR and DSC using the button
F Press this button.
The orange indicator lamp in the button comes
on.
The ASR and DSC systems will no longer have
an effect on engine operation or the brakes in
the event of an involuntary change of trajectory.
Deactivation of ASR using the touch screen
The deactivation is configured in the
Driving/Vehicle menu.
It is confirmed by the display of a
message.
Reactivation
These systems are reactivated automatically
each time the ignition is switched back on or
above 31 mph (50 km/h).
Below 31
mph (50 km/h), you can reactivate
them manually.
5
Safety
Page 71 of 240
69
The warning label present on both sides of the
passenger sun visor repeats this advice.
In line with current legislation, you will find this
warning in all the required languages in the
following tables.
Passenger airbag OFF
Deactivating the front passenger
airbag
F With the ignition off, insert the key in the
passenger airbag deactivation switch.
F
T
urn it to the OFF position.
F
R
emove the key while keeping the switch in
this position.
When the ignition is switched on,
this warning lamp comes on in the
instrument panel. It stays on while
the airbag is deactivated. To ensure the safety of your child, the front
passenger airbag must be deactivated
when you install a
"rear ward facing" child
seat on the front passenger seat.
Otherwise, the child would risk being
seriously injured or killed if the airbag
were deployed.
Reactivating the front passenger
airbag
When you remove the "rear ward facing" child
seat, with the ignition off , turn the switch to
the ON position to reactivate the airbag and so
assure the safety of your front passenger in the
event of an impact.
When the ignition is switched on,
this warning lamp comes on in the
instrument panel, for approximately
one minute, to signal that the front
airbag is activated.
5
Safety
Page 84 of 240
82
F Insert the key into the ignition switch.
The system recognises the starting code.
F Unlock the steering column by simultaneously turning the steering wheel and the key.
In some cases, you may have to apply
some force to turn the steering wheel (if
the wheels are on full lock against a
kerb,
for example).
F
T
urn the key all the way towards the
dashboard to position 3
(Starting).
F
W
hen the engine starts, release the key.
With Petrol engines , after a
cold start,
preheating the catalytic converter can
cause clearly-felt engine vibrations when
stationary, with the engine running, for
anything up to 2
minutes (accelerated idle
speed).
Electronic immobiliser
The original key contains a coded electronic
c hip. When the ignition is switched on, starting
is only possible if the code is detected and
recognised.
This anti-theft protection locks the engine
management system a
few moments after the
ignition is switched off and prevents starting of
the engine following a
break-in.
In the event of a
fault, you are
informed by the illumination of this
warning lamp, the emission of an
audible signal and the display of
a
message.
In this case, your vehicle will not start; contact
a
PEUGEOT dealer as soon as possible.
Switching off
F Immobilise the vehicle.
F T urn the key fully towards you to position
1
(Stop) .
F
R
emove the key from the ignition switch.
F
T
o lock the steering column, turn the
steering until it locks.
Free-wheeling
For safety reasons, do not free-wheel.
Other wise, some vehicle functions will no
longer be active. To facilitate unlocking of the steering
column, the front wheels should be
straight before switching off the engine.
Switching off the engine leads to a
loss of
braking assistance.
Key left in
If the key has been left in the ignition
switch at position 2
(Ignition on)
, the
ignition will be switched off automatically
after one hour.
To switch the ignition back on, turn the key
to position 1
(Stop)
, then back to position
2
(Ignition on)
.Parking brake
Releasing
Driving
Page 85 of 240
83
F Pull the parking brake lever up slightly, press the release button then lower the
lever fully.
When the vehicle is being driven,
if this warning lamp and the STOP
warning lamp come on, accompanied
by an audible signal and a
message
on the screen, this indicates that the
parking brake is still applied or has
not been fully released. Remember
to fully lower the parking brake lever.
Applying
F Pull the lever up to immobilise your vehicle. When parking on a steep slope, direct
your wheels against the kerb, apply the
parking brake, engage a gear opposite
to the direction the vehicle is facing and
switch off the ignition.
On return to the vehicle, remember that
a gear had been engaged before starting
the engine.
If excessive travel or a loss of
effectiveness of this system is noticed,
the parking brake must be checked, even
between two services.
Checks of this safety-related system
must be carried by a PEUGEOT dealer or
a
qualified workshop.
Manual gearbox
5-speed
F Move the gear lever fully to the right to
engage 5th g e a r.
Engaging reverse gear
F Move the gear lever to the right then pull it back.
Only engage reverse gear when the
vehicle is stationary with the engine at idle.
6-speed
F Move the lever fully to the right to engage 5th
or 6th g e a r.
Engaging reverse gear
6
Driving