Peugeot 208 2019 Workshop Manual

49
12 V accessory socket
F To connect a 12 V accessory (maximum
power: 120 watts), lift the cover and plug in
the correct adapter.
Do not exceed the maximum power rating
of the socket (risk of damage to your
accessory).
USB socket
The USB socket allows the connection of
a portable device, such as an iPod®-type digital
audio player, or a

USB memory stick.
The USB reader reads your audio files, which
are then transmitted to your audio system and
played via the vehicle's speakers.
These files are managed via the steering wheel
controls or from the audio system.
When connected to the USB socket,
the portable device can be charged
automatically.
While charging, a message is displayed
if the power consumption of the portable
device exceeds the amperage supplied by
the vehicle.
Boot fittings
1.Rear shelf
2. Hooks
3. Boot lamp
4. Stowing rings (depending on version)
The connection of an electrical device
not approved by PEUGEOT, such as
a

USB charger, may adversely affect the
operation of vehicle electrical systems,
causing faults such as poor radio
reception or inter ference with displays in
the screens.
For more detail on the Audio equipment and
telematics, and particularly the USB socket,
refer to the corresponding part of the audio
equipment section. The USB socket also allows a
smartphone to
be connected by MirrorLink
TM, Android Auto®
or CarPlay®, so that certain applications on the
smartphone can be used on the touch screen.
3
Ease of use and comfort

50
Rear shelf
To remove the shelf:
F u nhook the two cords,
F

g
ently lift the shelf, then remove it.
Stow it:
-
v

ertically behind the rear seats,
-
v

ertically behind the front seats. To refit the shelf:
F

e
ngage it on the supports on each side and
slide it until it reaches the notches,
F
r
aise it to refit the two cords.
When sharp deceleration occurs,
objects placed on the shelf can turn into
projectiles.
Ease of use and comfort

51
Lighting control stalk
In some weather conditions (e.g. low
temperature or humidity), the presence
of misting on the internal sur face of the
glass of the headlamps and rear lamps is
normal; it disappears after the lamps have
been on for a few minutes.
Travelling abroad
If planning to use your vehicle in a
country
that drives on the other side of the road,
the dipped beam headlamps must be
adjusted to avoid dazzling oncoming
drivers. Contact a
PEUGEOT dealer or
a


qualified workshop.
Selection of main lighting
mode
Lighting off (ignition off)/Front daytime
running lamps (engine running).
Sidelamps only.
Dipped or main beam headlamps.
Automatic illumination of headlamps.
Headlamp dipping
In the lighting off and sidelamps modes, the
driver can switch on the main beam headlamps
temporarily ("headlamp flash") by maintaining
a pull on the stalk.
Display
Illumination of the corresponding indicator
lamp in the instrument panel confirms that the
lighting selected is on.
Foglamps
The foglamps operate with dipped or main
beam headlamps on.
Turn the ring to align the desired symbol with
the marking. Pull the stalk to switch between dipped and
main beam headlamps.
Rear foglamp only
F To switch it on, turn the ring for wards.
When the lighting is switched off automatically
(version with AUTO lighting), the foglamp and
the dipped beam headlamps will remain on.
F

T
o switch it off, turn the ring rear wards.
Front foglamps and rear foglamp
Rotate and release the ring:
F o nce for wards to switch on the front
foglamps,
F

f
or wards a second time to switch on the rear
foglamp,
F

o
nce rear wards to switch off the rear
foglamp,
F

r
ear wards a second time to switch off the
front foglamps.
4
Lighting and visibility

52
If the lighting is switched off automatically
(version with AUTO lighting) or the dipped
beams are switched off manually, the foglamps
and sidelamps remain on.
F
T
urn the ring rear wards to switch the
foglamps off; the sidelamps will then switch
of f.
In good or rainy weather, by day and
night, using the front and rear foglamps is
prohibited. In these situations, the power
of their beams may dazzle other drivers.
They should only be used in fog or falling
snow.
In these weather conditions, it is your
responsibility to switch on the foglamps
and dipped beam headlamps manually as
the sunshine sensor may detect sufficient
light.
Do not forget to turn off the front and rear
foglamps as soon as they are no longer
necessary.
Switching off of the lighting when the
ignition is switched off
On switching off the ignition, all of the
lighting turns off immediately, except for
dipped beam if automatic guide-me-home
lighting is activated. Switching on the lighting after the
ignition is switched off
To reactivate the lighting control stalk, set
the ring to position "
0" - lighting off, then to
the desired position.
On opening the driver's door, a
temporary
audible signal warns the driver that the
lighting is on.
The lamps, with the exception of the
sidelamps, switch off automatically after
a
maximum duration of 30 minutes to
prevent discharging of the battery.
Direction indicators
F Lower the lighting control stalk fully when turning left.
F

R
aise the lighting control stalk fully when
turning right. If you forget to cancel the direction
indicators for more than 20
seconds, the
volume of the audible signal will increase if
the speed is above 37 mph (60 km/h).
Three flashes
Move the stalk briefly upwards or downwards,
without going beyond the point of resistance;
the corresponding direction indicators will flash
three times.
This function can be used at any speed,
but it is particularly useful for changing
lane on fast roads.
Automatic illumination of
headlamps
When a low level of ambient light is detected by
t he sunshine sensor, the number plate lamps,
sidelamps and dipped beam headlamps are
switched on automatically, without any action
on the part of the driver. They may also come
on if rain is detected, at the same time as
automatic operation of the windscreen wipers.
As soon as the brightness returns to
a
sufficient level or after the windscreen wipers
are switched off, the lamps are switched off
automatically.
Lighting and visibility

53
Switching on
F Turn the ring to the "AUTO" position.
Activation of the function is accompanied by
a
message on the screen.
Switching off
F Turn the ring to another position. Deactivation of the function is accompanied
by a
message in the screen.
In fog or snow, the sunshine sensor may
detect sufficient light. In this case, the
lighting will not come on automatically.
Do not cover the sunshine sensor, linked
with the rain sensor and located in the
centre of the windscreen behind the rear
view mirror; the associated functions
would no longer be controlled.
Automatic guide-me-home
lighting
When associated with automatic illumination of
headlamps, the guide-me-home lighting offers
the following additional options:
-

s
election of the lighting duration of 15, 30 or
60


seconds,
-

a
utomatic activation of guide-me-home
lighting when the automatic illumination of
headlamps is in operation.
The guide-me-home lighting can be
configured in the Driving/Vehicle
menu.
In the event of a
fault with the
sunshine sensor, the lighting comes
on, this warning lamp is displayed
in the instrument panel and/or
a
message appears on the screen,
accompanied by an audible signal.
Contact a
PEUGEOT dealer or
a


qualified workshop.
Manual guide-me-home
lighting
Temporarily keeping the dipped beam
headlamps on after the vehicle's ignition has
been switched off makes the driver's exit easier
when the light is poor.
Switching on
F With the ignition off, "flash" the headlamps using the lighting control stalk.
F

A f
urther "headlamp flash" switches the
function off.
Manual guide-me-home lighting is
also available from the remote control
lighting button.
Switching off
Manual guide-me-home lighting goes off
automatically at the end of a given period of
time.
4
Lighting and visibility

54
Headlamp beam height
adjustment
To avoid causing a nuisance to other road
u sers, the height of the headlamp beams
should be adjusted according to the load in the
vehicle.
0. 1
or 2 people in the front seats.
-. Intermediate setting.
1. 5


people.
-. 5
people + maximum authorised load.
2. Driver + maximum authorised load.
The initial setting is position " 0".
Vehicle side marking by illumination of the
sidelamps on the traffic side only.
F

W

ithin one minute after switching off the
ignition, operate the lighting control stalk up
or down, depending on the traffic side (for
example, when parked on the left, move the
lighting control stalk upwards; the right-hand
sidelamps come on).
This is confirmed by an audible signal and
illumination of the corresponding direction
indicator lamp in the instrument panel.
To switch off the parking lamps, return the
lighting control stalk to the middle position or
switch on the ignition.
Parking lamps Daytime running lamps/
Sidelamps
The front and rear lamps light up automatically
when the engine starts.
They provide the following functions:
-

D
aytime running lamps (lighting control
stalk at position " 0" or " AUTO " with
adequate light level).
-

S
idelamps (lighting control stalk at " AUTO"
position with low light levels or "Sidelamps
only" or "Dipped/main beam headlamps").
The LEDs are brighter when operating as
daytime running lamps.
Lighting and visibility

55
Cornering lighting
Activation
DeactivationWith dipped or main beam headlamps, this
system makes use of the beam from a front
foglamp to illuminate the inside of a
bend,
when the vehicle speed is below 25
mph
(approximately 40
km/h) (urban driving, winding
road, intersections, parking manoeuvres, etc.).
Without cornering lighting With cornering lighting
This function operates:
-

w
hen the corresponding direction indicator
is switched on,
or
-

f
rom a certain angle of rotation of the
steering wheel.
The system does not operate:
-

b
elow a certain angle of rotation of the
steering wheel,
-

a
bove 25 mph (40 km/h),
-
w

hen reverse gear is engaged.
Programming
It is possible to activate or deactivate
the cornering lighting from the
Driving/Vehicle menu.
This system is activated by default.
Wiper control stalk
In wintry conditions, remove snow, ice or
frost present on the windscreen, around
the wiper arms and blades and the
windscreen seal, before operating the
wipers.
Do not operate the wipers on a
dry
windscreen. Under extremely hot or cold
conditions, ensure that the wiper blades
are not stuck to the windscreen before
operating the wipers.
4
Lighting and visibility

56
Automatic rain sensitive
windscreen wipers
The windscreen wipers operate
automatically, without any action
on the part of the driver, when rain
is detected (sensor behind the rear
view mirror), adapting their speed to
the intensity of the rainfall.
Switching on
This indicator lamp comes on in the
instrument panel and a message is
displayed.
Give a

short downwards push to the control
stalk.
A wiping cycle confirms that the instruction has
been accepted.
Switching off
This indicator lamp goes off in the
instrument panel and a message is
displayed.
Give another short downwards push to
the control stalk or shift the control stalk to
a

different position (Int, 1 or 2). If the wipers operate in intermittent mode
when in AUTO mode, have the system
checked by a
PEUGEOT dealer or
a

qualified workshop.
Do not cover the rain sensor, combined with
the sunshine sensor, located at the top of
the windscreen behind the rear view mirror.
When using an automatic car wash, switch
off the automatic rain sensitive wipers.
In winter, it is advisable to wait until the
windscreen is completely clear of ice before
activating the automatic rain sensitive
wipers.
Front screenwash
Pull the wiper control stalk towards you. The
screenwash and then the wipers operate for
a
preset time.
Front wipers
Fast (heavy rain).
Normal (moderate rain).
Intermittent (proportional to the
speed of the vehicle).
Of f.
Single wipe (press down and
release). The automatic rain sensitive windscreen
wipers must be reactivated by pushing the
control stalk downwards, if the ignition has
been off for more than 1
minute.
Lighting and visibility

57
Changing a wiper blade
This position permits release of the windscreen
wiper blades.
It is used for cleaning or replacing the wiper
blades. It can also be useful, in winter, to
release the wiper blades from the windscreen.
To move the wiper blades to the vertical position:
F O perate the wiper control stalk within one
minute after switching off the ignition to
position the wiper blades vertically on the
windscreen.
To return them to the park position:
F

S
witch on the ignition and operate the wiper
control stalk.
Removing a wiper blade
F Lift the corresponding wiper arm.
F U nclip and remove the wiper blade.
Fitting a new wiper blade
F Put the corresponding new wiper blade in place and clip it.
F

F
old down the wiper arm carefully. To maintain the effectiveness of the wiper
blades, it is advisable to:
-

h
andle them with care,
-
c
lean them regularly using soapy water,
-
a
void using them to retain cardboard on the
windscreen,
-
r
eplace them at the first signs of wear.
Rear wiper
Of f.
Intermittent wipe.
Wash-wipe (set duration).
If a

significant accumulation of snow or ice
is present, or when using a
bicycle carrier
on the boot, deactivate the automatic rear
wiper via the vehicle configuration menu
on the touch screen.
Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation if the windscreen wiper
is operating.
The activation or deactivation of
operation of the rear wiper when
engaging reverse gear can be set in
the Driving/Vehicle menu.
4
Lighting and visibility

58
General safety
recommendations
Labels are affixed in different locations on
your vehicle. They include safety warnings
and vehicle identification information. Do
not remove them: they are an integral part
of your vehicle.
For any work on your vehicle, use
a qualified workshop that has the technical
information, skills and equipment required,
all of which a
PEUGEOT dealer is able to
provide.
Depending on country regulations, some
safety equipment may be compulsory:
high visibility safety vests, warning
triangles, breathalysers, spare bulbs,
spare fuses, fire extinguisher, first aid kit,
mud flaps at the rear of the vehicle, etc. We draw your attention to the following
points:
-

T
he fitting of electrical equipment
or accessories not approved by
PEUGEOT may cause excessive
current consumption and faults and
failures with the electrical system of
your vehicle. Contact a
PEUGEOT
dealer for information on the range of
recommended accessories.
-

A
s a safety measure, access to
the diagnostic socket, used for the
vehicle's electronic systems, is
reser ved strictly for PEUGEOT dealers
or qualified workshop, equipped
with the special tools required (risk
of malfunctions of the vehicle's
electronic systems that could cause
breakdowns or serious accidents).
The manufacturer cannot be held
responsible if this advice is not
followed.
-

A
ny modification or adaptation not
intended or authorised by PEUGEOT
or carried out without meeting the
technical requirements defined by
the manufacturer will result in the
suspension of the legal and contractual
warranties. Installation of accessory radio
communication transmitters
Before installing a


radio communication
transmitter, you must contact a PEUGEOT
dealer for the specifications of compatible
transmitters (frequency, maximum power,
aerial position, specific installation
requirements), in line with the Vehicle
Electromagnetic Compatibility Directive
(2004/104/EC).
Hazard warning lamps
F When you press this red button, all four direction indicators flash.
They can operate with the ignition off.
Automatic operation of
hazard warning lamps
When braking in an emergency, depending on
the deceleration, the hazard warning lamps
come on automatically.
Safety