stop start Peugeot 3008 Hybrid 4 2013 Owner's Manual

4
FA
M
PRESENTATION OF THE HYBRID4 SYSTEM

26

Thank you for choosing a 3008 HYbrid4;
this vehicle has characteristics that are
different from conventional vehicles.
Study this handbook to learn about the
specifi c hybrid functions and for more
information, refer to the "Hybrid Sys-
tem" section.










The HYbrid4 technology allows two
sources of energy to be associated in
an effective manner: the Diesel HDi en-
gine, which drives the front wheels and
the electric motor, which drives the rear
wheels.
These two motors can operate alter-
nately or simultaneously, according to
the hybrid mode selected and the driv-
ing conditions.
The electric motor alone provides power
for the vehicle in "ZEV" (Zero Emissions
Vehicle) mode, and in "Auto" mode for
running at slow speed and low load. It
also assists the Diesel engine when
moving off, accelerating and changing
gear.
The battery that powers the electric
motor is recharged during phases of
deceleration and stores the energy for
subsequent use.


1.
Diesel HDi engine (front wheel drive).

2.
Electric motor (rear wheel drive).

3.
200 V battery.

4.
Electronic power supervisor.
5.
Stop & Start system.

6.
6-speed electronic gearbox.

7.
Electrical fl ow.

8.
HYbrid4 mode selector.

5
FA
M
How to start your vehicle


- Ensure that the gear lever is in posi-
tion N
.

- Switch the ignition on by turning the
key to position 2
.
If the Diesel pre-heating warning
lamp comes on (ambient tempera-
ture below freezing), wait unit it goes
off before starting.


- The instrument panel and the Ready

lamp come on. The power meter nee-
dle sweeps through its travel indicat-
ing that the hybrid system is active,
confi rmed by a message
; the dial in
the centre console is in AUTO
mode
(default mode for starting).

- The hybrid system determines
whether it is necessary to start the
Diesel engine.


- With the brake still applied, move
the gear lever to position A
to go
forwards or R
(by lifting the lever
slightly) for reverse.

- Lift your foot off the brake pedal, you
can move off.

- The parking brake is released auto-
matically as you move off, if confi gured
to do so (otherwise, release the park-
ing brake manually).

How to stop your vehicle andthe hybrid system



- Apply the brake until the vehicle
comes to a complete stop.

- Place the gear lever in position N
.

- Turn the ignition key to position 1
,
the parking brake is applied auto-
matically if confi gured to do so.

- Otherwise apply the parking brake
manually, the P
warning lamp must
be on.
- Press fi rmly on the brake pedal, turn
the ignition key to position 3
to start
up the hybrid system, then release
the key.

When stationary, switch off the
ignition and ensure that the
Ready
lamp is off before you
leave the vehicle, otherwise
the hybrid system will still be active.

For more information, refer to the "Un-
derbonnet precautions / warnings"
section.


When your vehicle starts in elec-
tric mode, this means that it
makes no noise. Be very careful of
pedestrians as they will not hear
you coming.

7
FA
M

Displays according to version in the
instrument panel screen or the main
screen.

This mode allows a more dynamic driving
style providing increased performance.
Acceleration and pickup are maximised
using the full capacity of the electric mo-
tor to supplement the Diesel engine.
The Stop & Start system also operates
in this mode.



This mode provides improved traction.
The Diesel engine drives the front
wheels continuously and the electric
motor drives the rear wheels.
Their coupling is managed automati-
cally to optimise traction on slippery
surfaces. This mode should be used on
snow covered roads and diffi cult ground
(mud, sand, …).
Sport mode
4WD mode (4 wheel drive)

HY
B
26
PRESENTATION










The HYbrid4 technology allows two
sources of energy to be associated in
an effective manner: the Diesel HDi en-
gine, which drives the front wheels and
the electric motor, which drives the rear
wheels.
These two motors can operate alter-
nately or simultaneously, according to
the hybrid mode selected and the driv-
ing conditions.
The electric motor alone provides power
for the vehicle in "ZEV" (Zero Emissions
Vehicle) mode, and in "Auto" mode for
running at slow speed and low load. It
also assists the Diesel engine when
moving off, accelerating and changing
gear.
The battery that powers the electric
motor is recharged during phases of
deceleration and stores the energy for
subsequent use.



1.
Diesel HDi engine (front wheel drive).

2.
Electric motor (rear wheel drive).

3.
200 V battery.

4.
Electronic power supervisor.
5.
Stop & Start system.

6.
6-speed electronic gearbox.

7.
Electrical fl ow.

8.
HYbrid4 mode selector.

27
Main parts of the HYbrid4 system

The HDi Diesel engine - 1
, located at the front, drives the front wheels and pro-
vides most of the power needed to drive the vehicle.
It is fi tted with the Stop & Start
system - 5
which recharges the batteries and pro-
vides additional power when needed (in 4x4 mode).

The electric motor - 2
, located at the rear, drives the rear wheels on its own, or
supplements the Diesel engine, according to the hybrid mode selected.
It recovers energy and charges the batteries during phases of deceleration of the
vehicle and is active up to 70 mph (120 km/h).

A 200 V NI-MH high voltage battery - 3
, provides a source of energy for the rear
electric motor.
Its charging rate is managed automatically by the vehicle during phases of decel-
eration.
It is located in a compartment in the boot, access to which is restricted to trained
service technicians.

The battery state of charge
is indicated by 8 horizontal or vertical bars (depending
on the screen).

The conventional battery
, located under the bonnet, powers the vehicle's 12 V
systems. It is recharged automatically by the high voltage network.

HY
B
28

The electronic power supervisor - 4
automatically manages the operation of
the two power units (Diesel and electric) to provide the lowest consumption.
An inverter and a transformer are needed to manage the electric power.
The inverter acts on the torque of the electric motor, by regulating the current
coming from the high voltage battery pack. Its operating range is between 150 and
270 volts.
The transformer converts the 200 V of the battery pack to 12 V, to power the
vehicle's ancillary systems.

The Stop & Start system - 5
allows the Diesel engine to be put into standby dur-
ing stops (traffi c lights, a stop, or in a traffi c jam, for example) or during phases of
running in all-electric mode.
The stopping and restarting of the Diesel engine is done in a way that is instanta-
neous and transparent for the driver.

The electronic gearbox - 6
provides, in automatic mode, signifi cant savings in
fuel consumption compared to a conventional manual gearbox, thanks to its elec-
tronic control system.
It also offers improved driving pleasure with the possibility at any time of choosing
the gear changing mode: automatic or manual, using the paddles located behind
the steering wheel.

HY
B
29
How to start your vehicle


- Ensure that the gear lever is in posi-
tion N
.

- Switch the ignition on by turning the
key to position 2
.
If the Diesel pre-heating warning
lamp comes on (ambient tempera-
ture below freezing), wait unit it goes
off before starting.

- Press fi rmly on the brake pedal, turn
the ignition key to position 3
to start
up the hybrid system, then release
the key.


- The instrument panel and the Ready

lamp come on. The power meter
needle sweeps through its travel
indicating that the hybrid system
is active, confi rmed by a mes-
sage
; the dial in the centre console
is in AUTO
mode (default mode for
starting).

- The hybrid system determines
whether it is necessary to start the
Diesel engine.


- With the brake still applied, move
the gear lever to position A
to go
forwards or R
(by lifting the lever
slightly) for reverse.

- Lift your foot off the brake pedal, you
can move off.

- The parking brake is released au-
tomatically as you move off, if con-
fi gured to do so (otherwise, release
the parking brake manually).

How to stop your vehicle andthe hybrid system



- Apply the brake until the vehicle
comes to a complete stop.

- Place the gear lever in position N
.

- Turn the ignition key to position 1
,
the parking brake is applied auto-
matically if confi gured to do so.

- Otherwise apply the parking brake
manually, the P
warning lamp must
be on.

For more information, refer to the
"Underbonnet precautions / warnings"
section.
When stationary, switch off the
ignition and ensure that the
Ready
lamp is off before you
leave the vehicle, otherwise
the hybrid system will still be active.


When your vehicle starts in
electric mode, this means
that it makes no noise. Be
very careful of pedestrians
as they will not hear you coming.

HY
B
36

Examples of displays


On starting and when stationary
There is no fl ow of energy (the Stop & Start system
stops and restarts the Diesel engine automatically).

Energy recovery
During this phase (deceleration, braking, foot off the
accelerator, … all modes), the battery is recharged by
the electric motor/generator, then being driven by the
rear wheels.
You can maximise this energy recovery by taking your
foot off the accelerator pedal, deceleration will then be
less marked than with a conventional vehicle.

100% electric
In all electric running (AUTO or ZEV modes), only the
electric motor, powered by the battery, drives the rear
wheels.
The display of "Zero Emission" indicates that the Diesel
engine is off and the vehicle is producing no CO
2.

HY
B
38
ECO OFF SWITCH


This function prevents the Diesel en-
gine being switched off and so ensures
that a comfortable temperature can be
maintained in the passenger compart-
ment (air conditioning running continu-
ously).
On pressing the switch, the engine re-
starts immediately.
To return to normal operation, press the
switch again.
After switching off the ignition, the vehi-
cle will return to normal operation (lamp
in the switch off).
During electric running and
when the engine is stopped,
the hybrid system manages
restarting automatically to as-
sure comfort levels in the passenger
compartment * .
However, variations in temperature
may still be felt in very hot climates.
To avoid any discomfort in these
conditions you can operate the ECO
OFF switch.




*
Except in ZEV mode, which favours
electric running over assuring a com-
fortable temperature.

HY
B
42
200 V HIGH VOLTAGE BATTERY

The 200 V high voltage battery cannot
be recharged from a mains supply.
The battery is Ni-MH (Nickel Metal Hy-
dride) and is located below the boot
fl oor, close to the electric motor.
Charging
The charging takes place automati-
cally when driving
.
The energy recovery can be faster dur-
ing deceleration.
The average state of charge is 4 to
5 bars, so preserving a margin for en-
ergy recovery when deceleration of go-
ing downhill (free energy).

The battery is charged when the vehi-
cle decelerates, the electric motor then
becomes a generator and converts ki-
netic energy into electrical energy (ex-
cept if the speed of the vehicle is above
70 mph (120 km/h)).
The battery is not recharged from a
mains supply.
The battery may also be charged auto-
matically when required by the Stop &
Start system of the Diesel engine.


To preserve the service life of
the battery, the level of charge
never falls below 20 %, even
if a level of 0 bars is displayed
after ZEV running.
Where the battery is close to maxi-
mum, vehicle deceleration with your
foot off the accelerator pedal will be
at a lower level.

This recovery allows the use of "free"
energy.
The battery charging time is very short
and is continuous.
A discharged battery (following ZEV
running or high load, for example) will
quickly return to a state of charge suf-
fi cient for full operation of the different
hybrid modes.