lock Peugeot 306 C Dag 2001 User Guide

Adjusting the height of the steering wheel Push the handle to unlock the steering wheel. Adjust the steering wheel to the desired height and pull the handle tolock it into position.
1
2
96
YOUR 306 CABRIOLET IN DETAIL
1 - Lighting rheostat* Dim or brighten the instru- ment panel lighting by turningthe knob.
This only operates when the exteriorlights are on. 2 - Headlight heightadjustment*
Depending on the vehicleÕs load, it is advisable to adjust
the headlight beam. 0 - 1 or 2 people in the front seats.
- - 3 people.
1 - 4 people.
2 - 4 people + maximum authorised
load.
3 - Driver + maximum authorised
load.
This adjustment can only be carried out with the lighting stalk in thedipped/main beam headlights posi-tion. Initial setting: 0.
* According to specification.

1
4
YOUR 306 CABRIOLET IN DETAIL
46
Inside the vehicle:
- Turn the ignition key to positionM (engine not running, oil
pressure warning light on).
- Unlock the hood using the two side handles 1.
- Raise the front of the hood approximately 10 inches (25 cm). - Press the switch
4on the cen-
tral console until the operation has been completed (hoodfolded in its housing and hoodcover closed).
ELECTRIC HOOD: OPENING

- From inside the vehicle, using thecentre handle and a side handle, fold down the front of the hood,position the side handle hooks intheir housings and secure the twohandles.
If the fault persists, contact your
PEUGEOT dealer.
A
B
1
If an electrical fault occurs while the hood is open, it is possible to close it manually.
Using the side handle 1, close the
hood and unfold it to the point of resistance.
- Close the rear of the hood.
- Close the hood cover and secure it by turning the wheelbrace Ba
quarter turn anti-clockwise.
- Fold down the rear of the hood on the hood cover.
Y OUR 306 CABRIOLET IN DETAIL
48
ELECTRIC HOOD:
MANUAL CLOSING Open the boot, remove the cap A.
Using the wheelbrace B, turn a quar-
ter turn clockwise in order to release the hood cover and open it.

- Release the two front side handles13 .
- Remove the hard top and carefully place it on a clean and stable stand. - From the boot, manually open the
hood cover 10. To do this, remove
the cap and turn the control aquarter turn clockwise using thewheelbrace. Remove the wheel-brace, close the boot and hold thehood cover 10open using the sec-
ond strap 2.
- Remove the two side brackets 12
using the 17 mm flat spanner 6.
- Connect connector 8to the har-
ness connector located behind theside flap 14on the right hand side
of the rear shelf (if the connectionis not made, the hood and blowerwill not operate).
- Remove the retaining straps 2
from the hood cover 10and from
the side flaps 7.
- Close the hood cover 10manually.
- Switch on the ignition.
- Close the hood and the windows.
12
13
10
2 Before folding the hood into its housing, ensurethat it has been brushedand dried to remove any
moisture and that the rear screen
is folded correctly.
To prevent damage to the hood cover and the boot, the boot mustbe closed during the hood coverlowering and raising operations. Although the hood cover may appear to support itself in the ver-tical position, it must be securedusing a strap.
Take extreme care when handling the hard top to avoid scratching ordamaging it. Do not lean the hard top against a wall or place it in an unstableposition. Store the hard top on a stand in a clean, dry environment and coverit. When the hood has been folded for a long time, ask a PEUGEOTdealer to remove any creases. Imperative The hard top heated rear screen harness must be connected at alltimes. If the harness is not con-nected significant damage mayresult from accidental operation.
The ignition must be switched off for all operations.
(except during the hood cover manoevring phase for the electric hood).
Y OUR 306 CABRIOLET IN DETAIL 51

- Secure the two side brackets 12to
the vehicle using the 17mm span- ner 6.
- Disconnect connector 8from the
harness located behind the sideflap 14on the right hand side of
the rear shelf. - Remove the retaining strap
2from
the hood cover 10.
- From the boot, close the hood cover 10manually. To do this,
remove the cap and turn the con-trol a quarter turn anti-clockwiseusing the wheelbrace. Remove thewheelbrace, reposition the capand close the boot.
Take care not to trap the harness.
- Carefully position the hard top: place the front edge of the roof incontact with the seal of the uppersection of the windscreen. Position the rear section of the roof on the side brackets 12.
Place the restraining straps
2on the
two side flaps 7and the hood cover
10 .
HARD-TOP: REFITTING
Tools
Your hard-top is supplied with a tool kit containing: 1
- A storage case.
2 - Two retaining straps.
3 - A screwdriver with two heads.
4 - A pair of gloves.
5 - A special spanner.
6 - A 17mm flat spanner.
6
3
5 1 4
2
10
14
2
82
7
5
12
Switch on the ignition. Open all the windows.
Lower the hood completely.
Switch off the ignition.Open the hood cover
WARNING The removal-refitting operations described below should have beendemonstrated by your PEUGEOTdealer on handover of your vehicle. If your hard-top was supplied as
an accessory, the first removaloperation must be carried out by
an approved dealer. The opera-tion must be carried out by threepeople.
Y OUR 306 CABRIOLET IN DETAIL
52

YOUR 306 CABRIOLET IN DETAIL
60
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "ON/VOL"button to switch the set
on or off. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows "CODE"then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again. After incorrectly inputting the code 14 times, the radio will be permanently locked and the display will read " END".
ADJUSTING THE SOUND Adjusting the volume
Turn the "ON/VOL" button to increase or decrease the volume of the set.
If the radio overheats, the volume reduces. If an attempt is made to increase the volume the message " TOO HOTÕÕ
appears on the display. Note If you have a telephone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the telephone is used.

70
YOUR 306 CABRIOLET IN DETAIL
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "ON/VOL"button to switch the set
on or off. The set can operate for 30 minutes without switching the ignition on. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows Ò CODEÓ then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically. Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again. After incorrectly inputting the code 14 times, the radio will be permanently locked and will display the message ADJUSTING THE SOUND Adjusting the volume
Turn the " ON/VOL" button Mto increase or decrease the volume of the set.
In the event of the radio overheating, the volume level decreases.
Note
If you have a car-phone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the car-phone is used.

321
YOUR 306 CABRIOLET IN DETAIL
56
To quickly de-ice or demist the windscreen and the side windows, set the heating and air flow controls to maximum.
To obtain even air distribution, ensure that the external air intake vent and the ven- tilation vents are not blocked and that the air can move freely under the front seats. 2 Adjusting the temperature
Turn the knob
2to the blue zone
(outside temperature) or to the red zone (hot).
3 Adjusting the air flow
Turn the knob 3to the required flow
position.
This position prevents the
entry of outside air. It mustonly be used for a short timeto prevent the entry ofunpleasant odours or dust.
1 Adjusting the air distribution
To direct hot or cold air, turn knob 1to the desired position.
Windscreen and side windows. Windscreen, side windows and footwells. Footwells only. Side and central vents.
HEATING

THE REMOTE CONTROL
A single press on button Alocks the
doors and boot, this is displayed by the direction indicators staying on forabout 2 seconds.
A single press on button Bunlocks the
vehicle, this is displayed by the direc-
tion indicators flashing rapidly.
KEYS
Without central locking The key individually Iocks and unlocks the doors and boot.
With central locking
Turning the key in the driverÕs door lock will lock or unlock the doors andboot. If either of the front doors is notclosed, the central locking will notwork.
A
B
YOUR
306 CABRIOLET IN DETAIL
78
CHANGING THE REMOTE
CONTROL BATTERIES
To gain access to the battery, unclip the key casing with a coin where youcan see the ring (CR
1620/3 volt
battery). If the remote control does not work after the battery has been changed,re-programme the remote control.
PROGRAMMING THEREMOTE CONTROL Manual synchronisation
- Switch off the ignition,
- Switch on the ignition,
- Immediately after switching on the ignition press button A.
The remote control is now working again. Automatic synchronisation
- Switch on the ignition (position M),
- Switch off the ignition and, during the next four minutes, lock the vehicle using the remote control(button A).
The remote control is now workingagain.
Note: Do not repeatedly press the button of your remote control out of range of
your vehicle. You risk causing it not towork and the remote control wouldhave to be reprogrammed.

1
2
79
YOUR 306 CABRIOLET IN DETAIL
Locking or unlocking the boot The boot can be locked indepen- dently using the key or togerther withthe doors by way of the central lock-ing function. The boot can only be unlocked using
the key. This system prevents unauthorised access to the boot when the hood isopen.
Opening and closing thedoors from inside the vehicle 1
Locking control.
2 Opening handle. Take careful note of the numbers on the keys. The key number is coded on the label attached to
the key. If the key is lost
your PEUGEOT dealer can rapid-ly supply you with new keys or aremote control. As a safety precaution (with chil- dren on board) remove the igni-tion key when you leave the vehi-cle, even for a short time. The high frequency remote con- trol is a high-performance systemwhich has a powerful beam.Therefore do not operate it while itis in your pocket as there is a pos-sibility that it may unlock yourvehicle.