key battery Peugeot 306 C Dag 2001 Owner's Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2001, Model line: 306 C Dag, Model: Peugeot 306 C Dag 2001Pages: 133, PDF Size: 2.05 MB
Page 30 of 133
Using the centre handle and a side handle, fold down the front of thehood, position the side handle hooksin their housings and secure the twohandles.
ELECTRIC HOOD: CLOSING Inside the vehicle:
- Turn the ignition key to position
M
(engine not running, oil pressure warning light on) and lower thefront windows.
- Press the switch 4on the central
console until the operation hasbeen completed (hood unfoldeduntil it stops not quite flush with thewindscreen).
4 As a safety precaution, opening and closingoperations must be car-
ried out when stationary.Driving with the hood
cover open is prohibited. If the boot is not closed, the hood cannot be opened or raised. If the front of the hood is not raised, the hood cannot beopened. Do not carry out too many opera- tions in succession as there is arisk that the battery may becomeflat. Do not place anything in the com- partment reserved for storing thehood as there is a risk of damage. Before opening the hood:
- Ensure that the hood and rear screen are clean.
- Ensure that the hood is dry, oth- erwise the compression it is subjected to when it is foldedwill result in marks or evenstains caused by moisture overtime.
Y OUR 306 CABRIOLET IN DETAIL 47
Page 39 of 133
YOUR 306 CABRIOLET IN DETAIL
60
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "ON/VOL"button to switch the set
on or off. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows "CODE"then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically.
Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the
code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again. After incorrectly inputting the code 14 times, the radio will be permanently locked and the display will read " END".
ADJUSTING THE SOUND Adjusting the volume
Turn the "ON/VOL" button to increase or decrease the volume of the set.
If the radio overheats, the volume reduces. If an attempt is made to increase the volume the message " TOO HOTÕÕ
appears on the display. Note If you have a telephone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the telephone is used.
Page 50 of 133
70
YOUR 306 CABRIOLET IN DETAIL
GENERAL FUNCTIONS On / off
With the ignition key in the ACCESSORIES or IGNITION position, press the "ON/VOL"button to switch the set
on or off. The set can operate for 30 minutes without switching the ignition on. ANTI-THEFT SYSTEM
The first time you use the set following disconnection of the set or the battery, you must enter the confidential code which was given to you on handover of your vehicle. Entering the code Switch the set on. The display shows Ò CODEÓ then the set changes over to code request mode and " - - - -" is displayed.
Enter your four-digitcode number using buttons " 1" to " 6".
For example: if your code is 5345 press buttons " 5", " 3", " 4" and " 5" in turn.
When the fourth number has been entered correctly, the radio starts automatically. Error in entering the code
If an error is made when entering one of the first three digits, do not continue the operation and switch off the radio to prevent blocking it. Each incorrect code entry will result in the set being blocked for a period of from 5 seconds to 30 minutes, after
the 7th incorrect entry.
To unblock the set, leave it switched on during the waiting period. When " - - - -" is displayed, you can enter the code again.
If the set is switched off during the waiting period, this waiting period will restart when the set is switched on again. After incorrectly inputting the code 14 times, the radio will be permanently locked and will display the message ADJUSTING THE SOUND Adjusting the volume
Turn the " ON/VOL" button Mto increase or decrease the volume of the set.
In the event of the radio overheating, the volume level decreases.
Note
If you have a car-phone fitted with a Ò muteÓ signal output connected to the set, the set will automatically change
to Ò mute Ó when the car-phone is used.
Page 67 of 133
THE REMOTE CONTROL
A single press on button Alocks the
doors and boot, this is displayed by the direction indicators staying on forabout 2 seconds.
A single press on button Bunlocks the
vehicle, this is displayed by the direc-
tion indicators flashing rapidly.
KEYS
Without central locking The key individually Iocks and unlocks the doors and boot.
With central locking
Turning the key in the driverÕs door lock will lock or unlock the doors andboot. If either of the front doors is notclosed, the central locking will notwork.
A
B
YOUR
306 CABRIOLET IN DETAIL
78
CHANGING THE REMOTE
CONTROL BATTERIES
To gain access to the battery, unclip the key casing with a coin where youcan see the ring (CR
1620/3 volt
battery). If the remote control does not work after the battery has been changed,re-programme the remote control.
PROGRAMMING THEREMOTE CONTROL Manual synchronisation
- Switch off the ignition,
- Switch on the ignition,
- Immediately after switching on the ignition press button A.
The remote control is now working again. Automatic synchronisation
- Switch on the ignition (position M),
- Switch off the ignition and, during the next four minutes, lock the vehicle using the remote control(button A).
The remote control is now workingagain.
Note: Do not repeatedly press the button of your remote control out of range of
your vehicle. You risk causing it not towork and the remote control wouldhave to be reprogrammed.