display Peugeot 307 2007.5 User Guide
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2007.5, Model line: 307, Model: Peugeot 307 2007.5Pages: 212, PDF Size: 7.59 MB
Page 25 of 212
INSTRUMENTS and CONTROLS
24
After switching on the ignition, three
functions are shown in succession:
- service indicator,
- engine oil level indicator,
- total distance recorder (total and trip distances).
Note : the total and trip distances are
displayed for 30 seconds when the
ignition is switched off, on opening
the driver’s door, as well as on lock-
ing and unlocking the vehicle.
It also displays the information relat-
ing to the cruise control or speed lim-
iter, when either of these is activated
(see corresponding section).
Service indicator
This indicates when the next service
is due in accordance with the manu-
facturer’s servicing schedule.
The point at which the next service
is due is calculated from the last indi-
cator zero reset (see corresponding
section). It is determined by two pa-
rameters:
- the distance travelled,
- the time which has elapsed since the last service.
Note: the distance remaining before
the next service may be weighted by
the time factor, depending on the us-
er’s driving habits. DISPLAY
In the event of under-revving or over-
r e v v i n g , t h e g e a r s e l e c t e d l a s h e s f o r
a few seconds, then the actual gear
engaged is displayed
This comes on when the
"SPORT" programme on
the automatic gearbox is se-
lected.
This comes on when the
"SNOW" programme on the
automatic gearbox is select-
ed.
A u t o m a t i c g e a r b o x i n d i c a t o r
l i g h t s
"SNOW" indicator light This is displayed if a gear is
not engaged correctly (selec-
tor between two positions).
"SPORT" indicator light
Invalid value during manual
operation
Page 26 of 212
INSTRUMENTS and CONTROLS
Operation
For 5 seconds after the ignition is
switched on, the spanner symbolis-
ing the servicing operations comes
on; the distance recorder display in-
dicates the number of miles [kilome-
tres] (rounded off) remaining until the
next service.
E x a m p l e : 4,800 miles/km remain be-
f o r e t h e n e x t s e r v i c e . F o r i v e s e c o n d s
after the ignition is switched on, the
display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
the display indicates the total and trip
distance. T h e s e r v i c e i s o v e r d u e .
T h e s p a n n e r l a s h e s f o r 5 s e c o n d s
after the ignition is switched on.
E x a m p l e : the service is overdue by
300 miles/km, your vehicle must be
serviced as soon as possible.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and the
spanner remains lit. The display indi-
cates the total and trip distance.
Note: the spanner may also come on
if more than two years have elapsed
since the last service.
T h e d i s t a n c e r e m a i n i n g t o
t h e n e x t s e r v i c e i s l e s s t h a n
5 0 0 m i l e s ( 1 , 0 0 0 k m ) .
E x a m p l e : 400 miles (900 km) remain
before the next service.
For 5 seconds after the ignition is
switched on, the display indicates:
5 seconds after the ignition was
switched on, the distance recorder
resumes its normal operation and
t h e s p a n n e r r e m a i n s l i t .
It indicates that a service must be
carried out soon. The display indi-
cates the total and trip distance.
Page 27 of 212
INSTRUMENTS and CONTROLS
26
Your PEUGEOT dealer carries out
this operation after each service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
Switch off the ignition,
Press and hold the trip recorder
reset button,
Switch on the ignition.
The display begins a countdown.
When the display shows "=0" , release
the button; the spanner disappears.
Important: after this operation, if you
wish to disconnect the battery, lock
t h e v e h i c l e a n d w a i t f o r a t l e a s t i v e
minutes, otherwise the zero re-set
will not be registered.
Engine oil level indicator
When the ignition is switched on, the
engine oil level is indicated for a few
seconds, after the service information.
Oil level correct
O i l l e v e l g a u g e f a u l t Flashing of " O I L - - "
indicates a malfunc-
tion of the engine oil
level gauge.
Contact a PEUGEOT dealer.
T h e l e v e l r e a d w i l l o n l y b e c o r r e c t
i f t h e v e h i c l e i s o n l e v e l g r o u n d
a n d t h e e n g i n e h a s b e e n o f f f o r
m o r e t h a n 1 5 m i n u t e s .
Flashing of
"OIL" ,
linked with the
service warning
light, accompa-
nied by an audible
signal and a mes-
sage on the multifunction display, in-
dicates a lack of oil which could dam-
age the engine.
I f t h e l a c k o f o i l i s c o n i r m e d b y a
check using the dipstick, it is essen-
tial that the level is topped up.
L a c k o f o i l D i p s t i c k
There are 2 marks on the
dipstick:
- never exceed level A,
- in position B, top up t h e l e v e l v i a t h e o i l i l l e r
cap, using the type of
oil suited to your en-
gine.
A = max.
B = min.
S e r v i c e i n d i c a t o r z e r o r e - s e t
Page 28 of 212
INSTRUMENTS and CONTROLS
27
With the lights on, press the button
to vary the intensity of the lighting of
the instruments and controls. When
the lighting reaches the minimum (or
maximum) setting, release the button
then press it again to increase (or re-
duce) the brightness.
As soon as the lighting is of the re-
quired brightness, release the button.
T r i p r e c o r d e r z e r o r e s e t
b u t t o n
With the ignition on, press the button
until the zeros appear.
Pressing the button enables you to
alternate between the distance re-
corder and cruise control or speed
limiter displays, when either of these
is activated.
L i g h t i n g r h e o s t a t
Page 29 of 212
INSTRUMENTS and CONTROLS
28
TRIP COMPUTER
Press the button, located at the
end of the
w i p e r s s t a l k , to dis-
play the various items of trip com-
puter data in succession. The trip computer data is the follow-
ing:
System which provides current infor-
mation concerning the route travelled
(range, consumption, ...).
Press the control for more than two
seconds to reset the distance trav-
elled, the average consumption
and the average speed to zero.
M o n o c h r o m e d i s p l a y A Z e r o r e s e t
D a t a d i s p l a y s - the range,
- the current consumption,
- the distance travelled,
- the average consumption,
- the average speed.
The next press then returns you
to the normal display.
Page 31 of 212
INSTRUMENTS and CONTROLS
30
D i s t a n c e r e m a i n i n g t o b e
travelled
(km or miles)
This is the distance remain-
i n g t o b e t r a v e l l e d t o t h e i n a l d e s t i n a -
tion. It is either calculated instantly by
the navigation system if guidance is
activated, or entered by the user.
If the distance is not entered, dashes
are displayed in place of the digits.
A v e r a g e s p e e d
(km/h or mph)
This is the average speed cal-
culated since the last trip com-
puter zero reset (ignition on).
Range
(km or miles)
This indicates the number
of miles (or kilometres)
which can still be travelled with the
fuel remaining in the tank in relation
to the average consumption over the
last few miles (kilometres) travelled. C u r r e n t c o n s u m p t i o n
(l/100 km or km/l or mpg)
This is the average quantity
of fuel consumed over the
last few seconds.
A v e r a g e c o n s u m p t i o n
(l/100 km or km/l or mpg)
This is the average quan-
tity of fuel consumed since
the last trip computer zero reset.
D i s t a n c e t r a v e l l e d
(km or miles)
This indicates the dis-
tance travelled since the
last trip computer zero
reset.
A f e w d e f i n i t i o n s …
When the range falls below 20 miles
(30 km), dashes are displayed. After
i l l i n g w i t h a t l e a s t 5 l i t r e s o f f u e l , t h e
range is recalculated and is displayed
when it exceeds 60 miles (100 km). If dashes are displayed con-
tinuously while driving in
place of the digits, contact a
PEUGEOT dealer. This function is only displayed
from 20 mph (30 km/h).
T h i s i g u r e m a y i n c r e a s e f o l -
lowing a change of driving
style or relief, resulting in a
s i g n i i c a n t c h a n g e i n t h e c u r -
rent consumption.
Page 32 of 212
INSTRUMENTS and CONTROLS
31
D i s p l a y C
Press the "MENU" button to gain
access to the general menu.
Press the arrows, then the "OK"
button to select the " T r i p c o m p u -
ter" menu.
On the "Trip computer" menu,
select one of the following appli-
cations:
W a r n i n g s l o g
This summarises the active warning
messages, displaying them in suc-
cession on the multifunction display.
S t a t u s o f t h e f u n c t i o n s
This summarises the active or inac-
tive status of the functions present on
the vehicle.
E n t e r t h e d i s t a n c e t o t h e
d e s t i n a t i o n
This enables you to enter an approxi-
m a t e v a l u e f o r t h e d i s t a n c e t o t h e i -
nal destination.
"TRIP COMPUTER" MENU
System which provides general infor-
mation concerning the status of certain
equipment with which your vehicle is
equipped, such as the warnings log,
the status of the functions...
"DIAGNOSTICS" MENU
On the " D i a g n o s t i c s " menu, se-
lect one of the following applica-
tions:
C o l o u r d i s p l a y
Press the "MENU" button to gain
access to the general menu.
Turn the dial and press it to select
the " D i a g n o s t i c s " menu.
Page 33 of 212
MULTIFUNCTION DISPLAYS
32
Presentation
This displays the following information:
- the time,
- the date,
- the outside temperature * (this l a s h e s i f t h e r e i s a r i s k o f i c e ) ,
- t h e s t a t u s o f t h e a c c e s s e s ( d o o r s , b o o t , . . . ) ,
- the warning messages (e.g.: "Emis- s i o n c o n t r o l s y s t e m f a u l t y " ) o r i n f o r -
mation messages (e.g.: "Auto lights
o n " ) , d i s p l a y e d t e m p o r a r i l y , c a n
b e c l e a r e d b y p r e s s i n g t h e "ESC"
button,
- t h e t r i p c o m p u t e r ( s e e c o r r e - s p o n d i n g s e c t i o n ) .
* W i t h a i r c o n d i t i o n i n g o n l y .
Parameter configuration
T h e r e a r e t h r e e d i s p l a y c o n t r o l b u t t o n s :
- "ESC" to abandon the operation
in progress,
- "MENU" t o s c r o l l t h r o u g h t h e
menus or sub-menus,
- "OK" t o s e l e c t t h e m e n u o r s u b -
menu required.
General menu
Press the "MENU" b u t t o n t o s c r o l l
through the various menus of the
general menu:
- v e h i c l e c o n i g u r a t i o n ,
- options,
- display settings,
- languages,
- units.
Press the "OK" b u t t o n t o s e l e c t t h e
menu required.
(RD4 AUDIO EQUIPMENT)
Page 34 of 212
MULTIFUNCTION DISPLAYS
33
V e h i c l e c o n i g u r a t i o n
O n c e t h e " V e h i c l e c o n i g u r a t i o n "
m e n u h a s b e e n s e l e c t e d , y o u c a n
a c t i v a t e o r d e a c t i v a t e t h e f o l l o w i n g
equipment:
- w i p e r l i n k e d w i t h r e v e r s e g e a r ( r e f e r t o t h e " V i s i b i l i t y " s e c t i o n ) ,
- "follow-me-home" lighting (refer t o t h e " V i s i b i l i t y " s e c t i o n ) ,
- p a r k i n g a s s i s t a n c e ( r e f e r t o t h e " D r i v i n g " s e c t i o n ) .
Options
O n c e t h e " O p t i o n s " m e n u h a s b e e n
s e l e c t e d , y o u c a n s t a r t d i a g n o s t i c s o f
t h e s t a t u s o f t h e e q u i p m e n t ( a c t i v e ,
n o t a c t i v e , f a u l t y ) . Languages
O n c e t h e " L a n g u a g e s " m e n u h a s b e e n
s e l e c t e d , y o u c a n c h a n g e t h e l a n g u a g e
used by the display (Français, Italiano,
Nederlands, Portugues, Portugues-
B r a s i l , D e u t s c h , E n g l i s h , E s p a n o l ) .
Display settings
O n c e t h e " D i s p l a y s e t t i n g s " m e n u
h a s b e e n s e l e c t e d , y o u c a n g a i n a c -
c e s s t o t h e f o l l o w i n g s e t t i n g s :
- year,
- month,
- day,
- hour,
- minutes,
- 12 or 24 hour mode.
Units
O n c e t h e " U n i t s " m e n u h a s b e e n s e -
l e c t e d , y o u c a n c h a n g e t h e u n i t s o f
the following parameters:
- t e m p e r a t u r e ( ° C o r ° F ) ,
-
f u e l c o n s u m p t i o n ( l / 1 0 0 , m p g o r k m / l ) .
O n c e y o u h a v e s e l e c t e d a s e t t i n g ,
press the "OK" b u t t o n t o c h a n g e i t s
value.
W a i t f o r a p p r o x i m a t e l y t e n s e c -
o n d s w i t h o u t a n y a c t i o n t o a l l o w t h e
c h a n g e d d a t a t o b e r e c o r d e d o r p r e s s
the "ESC" b u t t o n t o c a n c e l .
The display then returns to the nor-
mal display.
F o r s a f e t y r e a s o n s , c o n i g u -
r a t i o n o f t h e m u l t i f u n c t i o n
displays by the driver must
t a k e p l a c e w h e n s t a t i o n a r y .
Page 35 of 212
MULTIFUNCTION DISPLAYS
34
* W i t h a i r c o n d i t i o n i n g o n l y .
General menu
Press the "MENU" b u t t o n t o g a i n a c -
c e s s t o t h e g e n e r a l m e n u , t h e n p r e s s
the "
" or "
" b u t t o n s t o s c r o l l
through the following items:
- radio-CD,
- v e h i c l e c o n i g u r a t i o n ,
- options,
- display settings,
- languages,
- units.
Press the "OK" b u t t o n t o s e l e c t t h e
menu required.
Presentation
This displays the following informa-
tion, via the RD4 audio equipment
c o n t r o l k e y p a d :
- the time,
- the date,
- the outside temperature * (this l a s h e s i f t h e r e i s a r i s k o f i c e ) ,
- t h e a u d i o s o u r c e d i s p l a y s ( r a d i o , C D , . . . ) ,
- t h e s t a t u s o f t h e a c c e s s e s ( d o o r s , b o o t , . . . ) ,
- the warning messages (e.g.: " E m i s s i o n c o n t r o l s y s t e m f a u l t y " )
or information messages (e.g.:
" A u t o l i g h t s o n " ) , d i s p l a y e d t e m -
p o r a r i l y , c a n b e c l e a r e d b y p r e s s -
ing the "ESC" button,
- t h e t r i p c o m p u t e r ( s e e c o r r e - s p o n d i n g s e c t i o n ) . Radio-CD
With the RD4 audio equipment
s w i t c h e d o n , o n c e t h e " R a d i o - C D "
m e n u h a s b e e n s e l e c t e d , y o u c a n
a c t i v a t e o r d e a c t i v a t e t h e f u n c t i o n s
l i n k e d w i t h t h e u s e o f t h e r a d i o ( R D S
f o l l o w i n g , R E G m o d e ) , t h e C D o r t h e
C D c h a n g e r ( i n t r o s c a n , r a n d o m p l a y ,
C D r e p e a t ) .
F o r f u r t h e r d e t a i l s c o n c e r n i n g t h e
" R a d i o - C D " a p p l i c a t i o n , r e f e r t o t h e
RD4 part of the "Audio and Telemat-
i c s " s e c t i o n . V e h i c l e c o n i g u r a t i o n
O n c e t h e " V e h i c l e c o n i g u r a t i o n "
m e n u h a s b e e n s e l e c t e d , y o u c a n
a c t i v a t e o r d e a c t i v a t e t h e f o l l o w i n g
equipment:
- r e a r w i p e r l i n k e d w i t h r e v e r s e g e a r
( r e f e r t o t h e " V i s i b i l i t y " s e c t i o n ) ,
- "follow-me-home" lighting (refer t o t h e " V i s i b i l i t y " s e c t i o n ) ,
- p a r k i n g a s s i s t a n c e ( r e f e r t o t h e " D r i v i n g " s e c t i o n ) .
Options
O n c e t h e " O p t i o n s " m e n u h a s b e e n
s e l e c t e d , y o u c a n s t a r t d i a g n o s t i c s o f
t h e s t a t u s o f t h e e q u i p m e n t ( a c t i v e ,
n o t a c t i v e , f a u l t y ) .
MONOCHROME DISPLAY A